Thermador PCG486GD Support Question
Thermador PCG486GD Support Question
Find answers below for this question about Thermador PCG486GD.Need a Thermador PCG486GD manual? We have 4 online manuals for this item!
Question posted by beatrizmc on December 16th, 2015
Ice Maker Installation Kit 1/4' Od Copper Line
I purchased a Thermador fridge which asks for an "Ice maker installation kit ¼" OD copper line". What is this? Do I have to purchase it separately? I rally would appreciate any help because I had it shipped out to outside of the US and do not have professional help available. Thanks!
Current Answers
Answer #1: Posted by kcmjr on December 17th, 2015 12:14 AM
kcmjr
Member since:
May 5th, 2011 Points: 4,254,245
Member since:
May 5th, 2011 Points: 4,254,245
Typically if the fridge does not have the ice maker installed out of the box you will need to buy the kit. It will require a water line tied from your sink faucet that runs to the fridge. Those are typically 1/4 inch pipes available at any hardware store. You can use copper or plastic but if it calls for copper I would stick with that. The plastic is far easier to work with.
Check out these links. They demonstrate what to do:
http://www.diynetwork.com/how-to/skills-and-know-how/plumbing/how-to-install-an-icemaker
https://www.youtube.com/watch?v=QrqwfoLHkVk
Search Google for the part number listed in the owners manual. You should be able to order the kit online. This posting shows the model number of a stove/range so I can't point you to a part.
Typically this is what you would look for (this might even be the one you need): http://www.appliancepartspros.com/thermador-refrigerator-ice-maker-kit.html
Good luck...
Licenses & Certifications: Microsoft, Cisco, VMware, Novell, FCC RF & Amateur Radio licensed.
Related Thermador PCG486GD Manual Pages
Design Guide - Professional Rangetops - Page 4
...installation site matches the type of shutting off valve must be installed external to assure it must be installed with Thermador Professional Rangetops. Where space permits, a hood larger in this design guide.
For high output gas cooktops....
A dedicated circuit breaker is recommended.
mODEL
PCG304G PCG364GD PCG366G PCG486GD
REQuIRED CIRCuIT BREakER
120V AC, 60Hz 15 Amp 15 Amp 15...
Design Guide - Professional Rangetops - Page 5
...Kit Quick Clean Base™ designed for any size pan - Exclusive, patented Star® Burner - Professional style, continuous cast iron grates - Star® design delivers superior heat spread for easy surface cleaning - Island trim shipped standard with rangetop
ACCESSORIES Important Note: A 12" Low Backguard or Island Trim is required for installation... Gas Cooktop Burners Center...
Design Guide - Professional Rangetops - Page 6
...www.Thermador.com for complete details before installing. to 34.9 mb) Manifold Pressure: 10" water column (24.9 mb)
1.800.735.4328 | THERMADOR.COM
65
naTuRaL GaS OR LP
Thermador Professional Rangetops are shipped by... information. aBOVE a WaRmInG DRaWER
Thermador Professional Rangetops may be ordered separately and installed at the installation site matches the type of the rangetop.
Design Guide - Professional Rangetops - Page 7
... LP Conversion Kit Widest range of Cooktop Burners Product Width Product Height
Product Depth Cutout Width Cutout Height Cutout Depth Minimum Distance from 375 BTU to 3,000 BTU - Star® design delivers superior heat spread for even heating
DESIGN - Titanium surface non-stick, rust-proof cast-aluminum grill - Island trim shipped standard with...
Design Guide - Professional Rangetops - Page 8
... REQuIREmEnTS:
Inlet Connection: 1/2" NPT (min. 3/4" dia. flex line) Supply Pressure: 11" min. water column (14.9 mb to support...may be considered when planning the installation. naTuRaL GaS OR LP
Thermador Professional Rangetops are shipped by the factory to create ... Thermador Professional Wall or Island Hood or Custom Insert be ordered separately and installed at the installation site...
Design Guide - Professional Rangetops - Page 9
... Kit Star® design delivers superior heat spread for easy surface cleaning - Every burner 18,000 BTU (NG) - Bold Professional design - most even heating,
unsurpassed flame coverage - Professional style, continuous cast iron grates - Island trim shipped standard with rangetop
AccESSORIES Important Note: A 12" Low Backguard or Island Trim is required for installation...
Design Guide - Professional Rangetops - Page 10
...separately and installed at the installation site matches the type of the warming drawer. It may be located in inches
ELECTRICaL anD GaS LOCaTIOnS
The gas and electrical supply must be converted for complete details before installing. Consult with the installation...dia. flex line) Supply Pressure: 6" min. naTuRaL GaS OR LP
Thermador Professional Rangetops are shipped by a quali&#...
Design Guide - Professional Rangetops - Page 11
... Breaker Power Cord Shipping Weight (lbs.)
6 47 15/16" 8 1/16" 25 13/16" 46 1/4" 7 11/16" 22 13/16" 12" Porcelain 6 @ 18,000 BTU 6 pass, 1,630 W
108,000 BTU
Order Kit PALPKITHC 90,000 BTU 120V AC, 60 Hz 15 Amp 96", 3-Wire 188
PcG486GD
PERFORMANcE - Grill accessory is required for installation
PA48GLBc 12...
Design Guide - Professional Rangetops - Page 12
... ordered separately and installed at the installation site matches the type of gas used at the rear of the rangetop. Do not install a microwave-hood combination above a Thermador Warming Drawer... are shipped by a qualified cabinet worker. to 34.9 mb) Manifold Pressure: 5" water column (12.5 mb)
PROPANE GAS REQuIREMENTS:
inlet Connection: 1/2" nPT (min. 3/4" dia. flex line) Supply...
Installation Instructions PART 1 - Page 1
The (10) inch minimum side wall clearance shown in the Installation Instructions is five (5) inches, on either side of this appliance. Material no. 9000572915 NOTICE ---
CORRECTION for 5 inch minimum clearance to combustible side walls is NOT correct. This appliance is rated for CLEARANCES to COMBUSTIBLE SIDE WALLS
The correct minimum clearance to combustible side walls. ---
Installation Instructions PART3 - Page 2
... Preparation 5 Step 3: Unpacking, Moving, Placing and Anchoring the Cooktop 10 Step 4: Gas Requirements and Hookup 11 Step 5: Electrical Requirements, Connection and Grounding 12 Step 6: Backguard Installation 13 Step 7: Burner Test and Adjustment 13
Installer Checklist 14
To Clean and Protect Exterior Surfaces 15
This Thermador Appliance is made by BSH Home Appliances Corporation 5551...
Installation Instructions PART3 - Page 3
...be longer than 36 inches. WARNING:
If the information in this manual is being installed.
2. For Massachusetts Installations:
1. Do not store or use any phone in the vicinity of this appliance...touch any other flammable vapors and
liquids in your gas supplier from a neighbor's phone. Installation and service must be performed by the state, province or region where this or any electrical...
Installation Instructions PART3 - Page 4
...installation in manufactured (mobile) homes or for the type of the cooktop. Before turning power ON, be utilized when there is NOT designed for installation in Recreational Park Trailers. The Thermador...Gas - 6" min. INSTALLER: Please leave these Instructions for future reference.
Before installation, the model and serial numbers should be ordered separately and installed at 18,000 BTU...
Installation Instructions PART3 - Page 5
....1 current issue and National Gas Code ANSI/NFPA 70 - Remove all Thermador cooktops. Destroy the packaging after unpacking the appliance.
NOTICE:
Most hoods contain combustible components which must comply with packaging material. CAUTION
To eliminate risk of the owner and the installer to determine if additional requirements and/or standards apply to the...
Installation Instructions PART3 - Page 6
... with single-wall ducting.
Before starting installation, consult local building codes and agencies to the estimated blower capacity. Consider Make-Up Air:
• Due to the high volume of ventilation air, a source of outside replacement air is recommended to use with Thermador Professional Cooktops.
• Refer to www.Thermador.com for a complete selection of Professional...
Installation Instructions PART3 - Page 7
...are required. Completing the installation as per Figure 8 will provide clearance for the following installations:
• Wall installation, see Figure 3. • Island installation, see Detail A, ...copper. All above the cooking surface, a Thermador Low Backguard must be located in Figure 1. The gas and electrical supply must be solid combustible or non-combustible material. The cooktop ...
Installation Instructions PART3 - Page 9
Counter Sunk Screws
B See Detail A
D
B 23-5/16"
Figure 2: Installing Side Supports (both sides)
Figure 3: Wall Installation with Countertop Backsplash
Vent Hood Width Requirements Island - 42" or 48" Wide Hood for 36" Cooktop Island - 54" or 60" Wide Hood for 48" Cooktop
See Detail A
D
3/4" Min.
22-13/16"
Figure 4: Island Installation (No Countertop Backsplash) English 7
Installation Instructions PART3 - Page 13
... of the system at least 6.0" W.C. Step 4: Gas Requirements and Hookup
Cooktops are shipped by the factory to operate on natural gas.They must be converted for ...purchased or contact Thermador. Make sure the gas supply is responsible for the gas valves.
to 14" max.
Obey all leaks immediately after finding them.
Verify the type of gas being used at the installation...
User Manual - Page 3
.... Cooktops are shipped by qualified service personnel only. Z223.1 / NFPA 54 current issue and the National Electrical Code ANSI/NFPA No. 70 current issue or the Can - Refer to the Installation Instructions accompanying this appliance for this unit should be installed in addition to another, contact the dealer where the unit was purchased or contact Thermador...
User Manual - Page 17
...Installation Manual for griddle components to clean. However, a very small amount may be washed with warm soapy water then rinsed with the grill plate accessory for leveling the product. CAUTION:
The griddle element is not gouged when utensils are purchased separately... responsible for more details. Section 4: USING THE COOKTOP
About the Griddle
DESCRIPTION
(Available on some models)...
Similar Questions
Grate Part Thanks
Do you have a MIDDLE grate for this model sgs365fs/01?Mine is brokenThanks
Do you have a MIDDLE grate for this model sgs365fs/01?Mine is brokenThanks
(Posted by leonorchristensen 4 years ago)
Xlo Sparking
Just installed pcg486gd in counter. when plugged in, left upper burner continuously sparks with the ...
Just installed pcg486gd in counter. when plugged in, left upper burner continuously sparks with the ...
(Posted by steve72mav 10 years ago)
Broke Glasstop For The Thermador Ces366fs Electric Cooktop During Installation.
Once I get a new one, do I move all the components from the broken one into the new one.
Once I get a new one, do I move all the components from the broken one into the new one.
(Posted by wayneslee 12 years ago)