TP-Link TD-W8901G Support Question
TP-Link TD-W8901G Support Question
Find answers below for this question about TP-Link TD-W8901G - Wireless Router.Need a TP-Link TD-W8901G manual? We have 3 online manuals for this item!
Question posted by shvalinia on April 20th, 2011
No Internet Access
i configured my Modem , internet &dsl LED is turn on, but i have only 1 minute internet with lan cable .after that i cant open any pages.and i cant access to internet with wireless device .!!!!!!!!!!!
Current Answers
Related TP-Link TD-W8901G Manual Pages
Quick Installation Guide - Page 2
Note To configure the device, you run the Web based Quick Setup Wizard (method two). Power on the back of the Router display normally as the diagram below describes.
TP-LINK strongly recommends that your device. With the phone line well connected, if the ADSL LED turns off after flashing, please contact your ISP to your internet connection...
User Guide - Page 9
... the TD-W8901G 54M Wireless ADSL2+ Modem Router.
1.1 Product Overview
The device is designed to provide a simple and cost-effective ADSL Internet connection for the configuration. The advanced security enhancements, IP/MAC Filter, Application Filter and URL Filter can help messages are provided for a private Ethernet or 802.11g/802.11b wireless network.
The Router provides wireless LAN 64...
User Guide - Page 10
...TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide Internet...(CO). ¾ Provides integrated access of internet and route function which face to SOHO user. ¾ Real-time Configuration and device monitoring. ¾ Supports Multiple ...security and wireless LAN ACL (Access Control List).
1.3 Conventions
The Router or device mentioned in the pictures are just references for TD-W8901G without any...
User Guide - Page 11
...TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Chapter 2 Hardware Installation
2.1 The Front Panel
Figure 2-1 The LEDs locate on . ADSL On
The LINE port is disabled.
There is no successful PPP connection or the Router works on Bridge mode.
On
The wireless function is enabled but no data is abnormal.
4 There is a successful connection on the corresponding 1-4 (LAN...
User Guide - Page 13
... to the power connector on the rear panel of TD-W8901G. Step 4: Attach the power adapter. Connect the power adapter to the LAN port on the computers and LAN devices. Step 2: Connect the Ethernet cable. External splitter can divide the data and voice, and then you can access the Internet and make sure your broadband service provided by...
User Guide - Page 16
Figure 3-3 9 TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Figure 3-2 Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties
button.
User Guide - Page 18
... address must be lit. 2) Is the TCP/IP configuration for your PC correct? Figure 3-7 11 Figure 3-6 You can follow the steps below: 1) Is the connection between your PC and the Router correct?
The LEDs of the Router in the URL field: 192.168.1.1. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide If the result displayed is similar to...
User Guide - Page 20
... Next. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide and Connection Type. Figure 3-12
) Note:
If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to finish the Quick Start.
13 Figure 3-11 Step 5: Configure the...
User Guide - Page 22
... view the device information, including LAN, WAN and ADSL. Figure 4-1 Click any settings you have altered on the page, please click the SAVE button.
4.1 Status
Choose "Status", you click one of the Web-based Utility, there are main menus on the Interface Setup screen.
15 TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Chapter 4 Software Configuration
This User...
User Guide - Page 26
TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Statistics Table:
Transmit total PDUs Transmit
Statistics Transmit total..." 3.2: Login".
4.3 Interface Setup
Choose "Interface Setup", you will see the next submenus: Internet and LAN. The total errors occurred over the WLAN when wireless data is being received. The frames received over the ADSL port when data is being transmitted....
User Guide - Page 27
...), VCI (Virtual Channel Identifier) settings to take effect. In this Device, you can use ATM QoS to setup each PVC traffic line's ... to connect to configure the corresponding function.
4.3.1 Internet
Choose "Interface Setup→Internet" menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-6). TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide Click ...
User Guide - Page 28
TD-W8901G 54M Wireless ADSL2+ Modem Router... the NAT (Network Address Translation) function
for Cable services. The valid range is from 0 to...configure them according to your ISP provides you can leave it . • VPI: Identifies the virtual path between endpoints in an ATM network.
The valid range is
from
32 to 65535 (1 to internet...for this device. 21 These QoS types are four connection...
User Guide - Page 29
...Routing Information protocol) version
for disabling the RIP
function. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide ¾ TCP MTU Option: Enter the TCP MTU as 192.168...Broadcast format. • Direction: Select this option to establish membership in a multicast group. IGMP (Internet Group Multicast Protocol) is four IP octets separated by a dot (x.x.x.x), such as your desire. ...
User Guide - Page 31
TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide automatically. The IP address can be configured to act as the default gateway to internet from this ADSL Router. It makes your ISP. Figure 4-10
) Note:
After you finish the Internet configuration, please click SAVE to make the settings take effect.
4.3.2 LAN
Choose "Interface Setup→LAN" menu, and you will be either dynamically...
User Guide - Page 32
TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Figure 4-11 ¾ Router Local IP: These are both IGMP version 1 (IGMP v1) and IGMP v2. The LAN IP address is private to your internal ... for LAN interface, including RIP1, RIP2-B and RIP2-M. IGMP (Internet Group Multicast Protocol) is for the device. The ADSL ATU-R supports both sent in Figure 4-12).
25 IN only means the ADLS router will ...
User Guide - Page 36
...devices in the space provided. • Broadcast SSID: When wireless clients survey the local area for listening to configure security features of the characters on the keyboard). TD-W8901G 54M Wireless ADSL2+ Modem Router... for wireless networks to the Router. ¾ Wireless MAC Address Filter: Wireless access can...32 characters (use the default Wireless LAN Performance settings. "802.11...
User Guide - Page 49
.... The filtering includes Outgoing and Incoming, the detailed descriptions are permitted to access to the Router
remotely. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
Figure 4-33 ¾ ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. ¾ ACL Rule Index: Select the ACL rule index for the entry...
User Guide - Page 53
...make the rule to access the Internet, you can configure as the Rule type (shown in Figure 4-35), and then you can not match, and you select Next, the router will
skip the rule ... rule can configure the filter rules based on MAC address. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2). TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide ...
User Guide - Page 54
...or modify the entry. Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address
00-0A-EB-00-07-5F to access the Internet.
) Note:
After you want to make the rule take... 4-36), and then you can enter the IP / MAC Filter Set Index to save the entry. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide Select the "MAC" as the Rule Type on application.
47 Step 2: Select the IP/...
User Guide - Page 58
...password assigned to your ADSL Router by your DDNS account. ¾ Wildcard support: Select the option to turn on DYNDNS Wildcard or not. The router offers a Dynamic Domain Name... and "Password" for your Dynamic DNS provider. TD-W8901G 54M Wireless ADSL2+ Modem Router User Guide
4.5.5 DDNS
Choose "Access Management→DDNS", you can configure the DDNS function in the screen (shown in ...
Similar Questions
Cant Open Router Setting Td-w8901g
(Posted by tana8tra 10 years ago)
How To Find The Router Password Of My Router Tp-link W8901g
(Posted by jimrabe 10 years ago)
How To Get Router Username Td-w8901g
(Posted by letmtool 10 years ago)
I Want To Make Username And Password For Internet Access
(Posted by abdlgm2611 12 years ago)
No Internet Access!
i configured my Modem and i can connect to internet via cable but when i want to use wireless intern...
i configured my Modem and i can connect to internet via cable but when i want to use wireless intern...
(Posted by kkkhar 13 years ago)