Stihl HT 131 Support Question
Stihl HT 131 Support Question
Find answers below for this question about Stihl HT 131.Need a Stihl HT 131 manual? We have 1 online manual for this item!
Question posted by richardnwalters on November 8th, 2015
How Do You Get The Oil Pump Out For A Ht131
The person who posted this question about this Stihl product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TommyKervz on November 9th, 2015 2:20 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,793
Member since:
January 10th, 2013 Points: 17,776,793
Go here http://www.arboristsite.com/community/threads/oil-pump-location-on-stihl-ht-131-pole-pruner.134672/ for a possible solution.
Related Stihl HT 131 Manual Pages
Product Instruction Manual - Page 3
...Cable
18
4-MIX Engine
18
Fuel
18
Fueling
19
Chain Lubricant
21
Filling Chain Oil Tank
21
Checking Chain Lubrication
22
Adjusting the Telescoping Shaft
23
Fitting the Harness...Replacing the Chain
Sprocket
35
Maintaining and Sharpening the
Saw Chain
36
{
HT 100, HT 101, HT 130, HT 131
Inspections and Maintenance by Dealer
Maintenance and Care
Main Parts
Specifications
Special ...
Product Instruction Manual - Page 4
...machine or its products.
Indicates an imminent risk of
2
HT 100, HT 101, HT 130, HT 131 Indicates a hazardous situation which, if not avoided, could... Fuel tank for gasoline and engine oil mixture
Tank for bar and chain oil
A description of a step or...of property damage, including damage to operate manual fuel pump
Manual fuel pump
Warning! As a result, engineering changes and improvements...
Product Instruction Manual - Page 9
... the ground, because when the engine starts at all other in your instruction manual. HT 100, HT 101, HT 130, HT 131
7 Keep the handles clean and dry at starting work. Proper starting throttle and allow... of you pull the starter grip, do not attempt to keep them free of moisture, pitch, oil, fuel mix, grease or resin in the chapter "Mounting the Bar and Chain" of injury from...
Product Instruction Manual - Page 16
...chain oil in several controllable pieces. Avoid direct contact with a pressure washer.
Prune heavy branches (large diameter) in approved and properly labeled safety-type canisters only.
Disposal
HT 100, HT ... used to the required length (HT 101, HT 131 only). The shaft should be extended to the most comfortable position.
14
HT 100, HT 101, HT 130, HT 131 Do not throw cuttings into the...
Product Instruction Manual - Page 20
... otherwise on a fuel mixture of piston seizure and damage to the end of highquality gasoline and two-stroke air cooled engine oil. Fuel with various ethanol contents.
18
HT 100, HT 101, HT 130, HT 131 Use mid-grade unleaded gasoline with a minimum octane rating of 89 (R+M/2) and no more than 10% ethanol content. Some fuel...
Product Instruction Manual - Page 21
..., HT 101, HT 130, HT 131
19 Gasoline
Oil (STIHL 50:1 or equivalent high-quality oils)
US gal. 1 2 1/2 5
US fl.oz. 2.6 6.4 12.8
Dispose of personal injury from your power tool and make proper adjustments and repairs.
Close the container and shake it is facing upwards.
To reduce the risk of empty mixing-oil containers only at the pump...
Product Instruction Manual - Page 23
...cause the oil pump to ensure that the filler cap is therefore essential to run dry. It is facing up.
Waste oil does ...Oil Tank
N Position cap. Rapidly biodegradable STIHL Bioplus is sufficient for chain lubrication.
The service life of the chain and guide bar depends on the quality of fuel. N Position the machine so that no dirt falls into the tank. HT 100, HT 101, HT 130, HT 131...
Product Instruction Manual - Page 24
...22
HT 100, HT 101, HT 130, HT 131
N Fold the grip down , the reason may be opened and closed without chain lubrication. If the oil level in position with the top of oil.
N To close the oil ...N To open the tank, swing the grip to 3 minutes. Always check chain lubrication and the oil level in the chain, check chain tension and adjust if necessary - N Turn the filler cap ...
Product Instruction Manual - Page 28
...rope all the way - N Crank the engine until you have a safe and secure footing. N Continue cranking.
N Press the fuel pump bulb (9) at least five times - N Place the unit on the stop symbol (h) to fire.
even if the bulb is already ...engine settles down to e. N Open the throttle slightly. N Warm up the engine for a short period.
26
HT 100, HT 101, HT 130, HT 131
Product Instruction Manual - Page 29
... after about 5 to 20 pulls may be run until completely dry
N After refueling, press the fuel pump bulb at high revs (full throttle off load) for some time.
N Dry the spark plug. N...is flooded. During Operation
Do not make the mixture leaner to clear the combustion chamber.
HT 100, HT 101, HT 130, HT 131
27 N Turn the choke knob to be pulled along the bar by pulling the starter...
Product Instruction Manual - Page 30
... temperature during cutting work . N Regularly clean the oil inlet hole (1), the oilway (2) and the bar groove (3). in a dry location. This protects engine-mounted components (ignition, carburetor) from thermal overload. The drive link tangs will not ride on the bar rails.
28
HT 100, HT 101, HT 130, HT 131
Always slacken off , it is not slackened...
Product Instruction Manual - Page 33
... .
N Clean the spark arresting screen.
Wrong fuel mix (too much engine oil in operation. N Unscrew the spark plug.
If the screen is down on power, check the spark arresting screen in the muffler.
N Take out the screw (4). HT 100, HT 101, HT 130, HT 131
31
N Wait for the muffler to cool down firmly. N Refit the...
Product Instruction Manual - Page 34
... (A) and readjust if necessary - see "Specifications". Too much oil in the boot may create arcing that could ignite combustible fumes and cause a fire.
2
3
N Screw the spark plug (3) into the cylinder and fit the boot (2) (press it down firmly).
32
HT 100, HT 101, HT 130, HT 131 Dirty air filter.
- Rectify problems which have caused fouling...
Product Instruction Manual - Page 35
... with non-resinous oil. N Tie a simple overhand knot in direction of arrow h - N Coat the rope rotor bearing bore with washer (4) and pawl (5). to engage the anchor loop of the grip and the rope bushing (6).
N Thread the rope through the top of the rewind spring.
249BA015 KN
HT 100, HT 101, HT 130, HT 131
33 turn...
Product Instruction Manual - Page 36
...off the rotor.
34
HT 100, HT 101, HT 130, HT 131 N Remove the spring ...housing and pieces of the spring housing and uncoils: Refit it must still be under tension and could break.
Replacing a broken rewind spring
N Remove the rope rotor as shown in the direction of injury, wear face protection and work gloves. then go of non-resinous oil...
Product Instruction Manual - Page 37
... attention to check the depth of fuel properly in accordance with corrosion inhibiting oil. English
Checking and Replacing the Chain Sprocket
N Remove the chain sprocket cover... dry, high or locked location, out of the reach of original STIHL chain sprockets.
000BA054 KN
HT 100, HT 101, HT 130, HT 131
35
Use a gauge (special accessory) to the cylinder fins and air filter. N Fit the ...
Product Instruction Manual - Page 45
... Chain 14 Guide Bar 15 Oil Tank 16 Oil Filler Cap 17 Telescopic Drive Tube (Shaft)
(HT 101, HT 131) 18 Clamp Screw (HT 101, HT 131) 19 Chain Sprocket Cover 20 Hook 21 Chain Guard (Scabbard) 22 Chain Sprocket 23 Chain Tensioner 24 Fuel Filler Cap 25 Carburetor Adjusting Screws 26 Fuel Pump 27 Starter Grip 28 Muffler...
Product Instruction Manual - Page 46
... Cap For closing the oil tank.
17 Telescopic Drive Tube (Shaft) (HT 101, HT 131) Adjustable drive tube enables user to optimize machine's reach.
18 Clamp Screw (HT 101, HT 131) For adjusting the length...saw chain.
15 Oil Tank Tank for chain lubricating oil.
16 Oil Filler Cap For closing the fuel tank.
25 Carburetor Adjusting Screws For tuning the carburetor.
26 Fuel Pump Provides additional fuel...
Product Instruction Manual - Page 47
... mm)
Ignition System
Electronic magneto ignition
English
HT 100, HT 101
Spark plug (resistor
type):
Bosch USR 7AC
Electrode gap:
0.02 in. (0.5 mm)
HT 130, HT 131
Spark plug (resistor
type):
NKG CMR 6H
Electrode gap:
0.02 in. (0.5 mm)
Chain lubrication
Fully automatic, speed-controlled oil pump with rotary piston Oil tank capacity: 7.4 fl.oz (0.22 L)
Fuel System...
Product Instruction Manual - Page 50
...in this recommendation regarding quality and mixing ratio of the recommended 2-stroke fuel-oil
mixture (see also instruction "Fuel"). Limitations
This Emission Control Systems Warranty shall ... may be performed at and after the first scheduled replacement point.
48
HT 100, HT 101, HT 130, HT 131
Magneto or Electronic Ignition
System (Ignition Module) - Deviations from this manual... Pump -
Similar Questions
I Am Not Getting Any Oil To The Chain? Do You Have A Schematic Of The 131
Looking for a schematic of the 131.pole saw. I am not getting oil to the chain
Looking for a schematic of the 131.pole saw. I am not getting oil to the chain
(Posted by nffsim 7 years ago)
Ht 131 Pole Saw
my guy took aprt my ht131 and now i cant seem to get it back together so it will work properly they ...
my guy took aprt my ht131 and now i cant seem to get it back together so it will work properly they ...
(Posted by Kurttreeboss 7 years ago)
No Gas Into Stihl 131 Carb
Pole saw will not start. New plug - that remains dry even after priming. Have removed carb cover, an...
Pole saw will not start. New plug - that remains dry even after priming. Have removed carb cover, an...
(Posted by pasqua 8 years ago)
Oil Pump For Ms 271 Stihl
why does the oil run down between my bar and motor and very little comes off the bar. there is no ga...
why does the oil run down between my bar and motor and very little comes off the bar. there is no ga...
(Posted by davidbaker68db 9 years ago)
Oil Pump Piston Replacement For Stihl Ms 461 Chainsaw
Hello, I would like to know the correct procedure to replace the pump piston shaft on my MS 461.I wo...
Hello, I would like to know the correct procedure to replace the pump piston shaft on my MS 461.I wo...
(Posted by stu31726 10 years ago)