Singer 7258 Stylist Support Question
Singer 7258 Stylist Support Question
Find answers below for this question about Singer 7258 Stylist.Need a Singer 7258 Stylist manual? We have 1 online manual for this item!
Question posted by scottandjaynie on December 13th, 2012
Singer Futura Quartet Seq6000- How Do I Adjust The Presser Foot Bar?
How do I adjust the presser foot bar? I know there is a screw located on the side that will allow me to adjust the bar up or down. I have found what I thought to be the correct screw and tried a small hex tool with no luck. My problam is when I try to raise the presser foot I have to tab the presser foot bar to the left to realigh it before the foot will lift. If you look at the bar from the inside of the nmachine, you can see that is rests in a small hole and when I lower the presser foot it comes completely out of the hole and causes it to misaligh and sit directly on the machines feed.
Current Answers
Related Singer 7258 Stylist Manual Pages
Instruction Manual - Page 3
...
3. KNOWING YOUR SEWING MACHINE Machine identification 6 - 7 Accessories 8 - 9 Setting up your machine 10 - 11 Spool pins, Presser foot lifter 12 - 13 Darning plate 12 - 13 Converting to free-arm sewing 14 ...- 27 Adjusting top thread tension 28 - 29 Changing presser foot 28 - 29 Functions of control panel 30 - 33 Operation buttons 34 - 37
2. OTHER INFORMATION Satin stitch foot, Twin ...
Instruction Manual - Page 6
... bar
28. Needle clamp screw
31. Large extension table
36. Thread tension control
2
4. Pattern number reference guide
11. Buttonhole lever 20. Foot release lever
15
30. Bobbin cover release button
35. Thread guide
13
21. Operation buttons
12. 1. KNOWING YOUR SEWING MACHINE
MACHINE IDENTIFICATION
1. Bobbin winding tension disk
1
2. Thread cutter
3
6. Presser foot...
Instruction Manual - Page 8
.../Seam Ripper and Brush 9. Darning & embroidery foot 17.
Bobbins (4 total - 1 in machine) 3. Spool pin cap (small) 7. The Satin Foot (12) is called the General Purpose Foot and will be used for needle plate 10. When purchasing additional bobbins, be used for the majority of your Sewing machine is another very useful foot and should be sure they are...
Instruction Manual - Page 12
...presser foot to change presser foot.
3. Raise the lifter to the middle position to insert or remove fabric, and to sew.
2. The diameter of the spool pin cap should be larger than that of the spool itself. Place a spool of spool being used. Lift it . Select the correct...pin Porte-bobine Pasador carrete
PRESSER FOOT LIFTER
There are three positions for button sewing, free motion work and free...
Instruction Manual - Page 18
... by rotating the hand
1
wheel toward you to
2
allow you (counter-clockwise).
2. Bobbin cover will pop up sufficiently...a very important step as the bobbin can become unthreaded and cause sewing problems if it rotates clockwise.
4. Replace the bobbin cover plate onto... bobbin thread does not slip out of the machine under
the presser foot. Insert the bobbin making sure the bobbin rotates...
Instruction Manual - Page 20
... check:
1.) With the presser foot raised and the needle unthreaded, pull the thread. Turn the hand wheel toward you do this means you have not threaded the machine correctly and
3
need to rethread it into the pre-tension guide (2).
* Pull the thread into the tension discs (which are located
inside the machine) by first passing the...
Instruction Manual - Page 24
...up bobbin thread,
3
which will perform one of the features of the machine under the presser foot, leaving about 6"
4
(15 cm) clear.
24 PICKING UP BOBBIN ...THREAD
1. Always stopping with the needle "fully up" is one down-up cycle and stop with the needle up the bobbin thread is, with your computer sewing machine...
Instruction Manual - Page 26
...screw with the flat
side toward you (counter-clockwise).
3.
The following table is a practical guide to change the needle and will use a SINGER branded needle. Raise the needle bar ...sewing results, always use the same size and type of any fiber: cotton, linen, silk, wool, synthetic, rayon, blends. Helpful Hint: Placing a scrap of fabric under the presser foot and lowering the presser foot...
Instruction Manual - Page 28
... for straight stitch sewing.
Lower the presser foot lifter so that the stitching is largely determined by the balanced tension of both top and bottom) is usually only desirable for straight stitch sewing. Push presser foot release lever to a higher number or a lower number may improve sewing appearance. STRAIGHT STITCHING
The correct appearance of the machine) set at "AUTO...
Instruction Manual - Page 30
...ADJUSTMENT BUTTONS
Your sewing machine will produce your preference pushing manual adjustment buttons. NOTE: Some patterns offer more options for manual adjustments than others.
30
Stitch length Longueur du point Largo de puntada LCD display Écrans ECL Pantalla LCD Manual adjustment... CONTROL PANEL
PATTERN NUMBER SELECTION BUTTONS
When the machine is turned on, straight stitch is selected and...
Instruction Manual - Page 34
... you stop button Bouton de marche/arrêt Botón inicio/parada
START/STOP BUTTON ( )
When sewing without having the foot controller connected, the machine starts slowly when the start and end of the tacking stitches will sew. Push it is connected, start/stop button cannot be lit red and needle will continue to...
Instruction Manual - Page 42
... used for all types of face cover
as an aid for guiding your hands. Start/stop the sewing machine. Start the machine.
Programmable needle up/down button D. Presser foot lifter F. SETTINGS
C
Presser foot - Guide the fabric gently with the thread cutter located on the needle plate. When reaching the edge of the tension may be desired.
Thread tension...
Instruction Manual - Page 44
... FUNCTION
1. INSERTING ZIPPERS AND PIPING
Use zipper foot to sew to right of the foot. Press the foot control and the machine will sew 4 stitches in reverse and then 4 stitches in forward until the foot control is released.
2.
To sew down the right side, attach left side of zipper foot to presser foot holder so that needle passes through the opening...
Instruction Manual - Page 46
ZIGZAG STITCHING
SETTINGS :Presser foot - Under side Côté de dessous Reverso
Top side Côté de dessus Cara
ADJUSTING STITCH WIDTH AND LENGTH
Dark grey box indicates the Auto/default value set manualy. Slightly loosen the top thread tension and manually adjust the stitch length between 0.5 and 2.0 for appliqué, bar-tacking, etc.
If bobbin...
Instruction Manual - Page 48
... edge of the
fabric.
NOTE: In addition to the adjustment on curtains, trousers, skirts, etc. BLINDHEM STITCH
The blindhem stitch is almost invisible on the Blindhem
Foot (A) so that the needle just pierces the fabric fold and
the guide just rests against the fold. NOTE: It takes practice to the left.
Settings : Presser foot -
Instruction Manual - Page 50
... control. AUTO
This is required, place a darning needle on top of the button and sew over the folded edge, pulling the fabric in illustration requires manual adjustment of button.
General Purpose Foot :Thread tension control -
AUTO
Turn under the presser foot. Place the fabric right side up so that the zigzag part of the stitch...
Instruction Manual - Page 70
... (2).
3
4. CARING FOR YOUR MACHINE
CLEANING HOOK AREA AND FEED DOGS
1
Always disconnect the machine from the wall-outlet. Raise the needle to keep the essential parts clean at all purpose" oil as
indicated by removing the plug from power CAUTION supply by the arrows. (A, B)
NOTE: SINGER Brand Sewing Machine Oil is not suited for sewing machine lubrication.
5.
Instruction Manual - Page 72
... the three threads together under the presser foot to pass under it easily. NOTE: Needle threader cannot be broken. This is grooved to permit dense stitching to the back of the machine, leaving about 6" (15 cm) of a SINGER Brand 3mm (Style 2025) Twin Needle is most useful for sewing satin stitches and as for single...
Instruction Manual - Page 80
... page
26 - 27). * Machine is not threaded correctly (see page 20 - 21). * Top thread tension is too loose (see page 26 - 27). * Needle size is damaged.- Clean hook (see
page 16 - 17). Adjust thread tension (see page
26 - 27). * Needle is not raised when sewing stitch patterns.
- Fabric does not move. * Presser foot is too long...
Instruction Manual - Page 84
... outlet.
"Do not allow to break." 12. FOOT CONTROL (USA & Canada only)
Use Yamamoto Electric, Model YC-485 EC with a damaged needle plate as threading needle, changing needle, threading bobbin, or changing presser foot, etc." 15.
POLARIZED PLUGS CAUTION (USA & Canada only)
This appliance has a polarized plug (one way.
"Switch the sewing machine off ("0") position, then...
Similar Questions
Is There Repair Manual To Singer Futura Quartet Seqs 6700,
It's not recognize the hoop, too it has to much thread and knot under fabric and do not make Stitch ...
It's not recognize the hoop, too it has to much thread and knot under fabric and do not make Stitch ...
(Posted by ellierosariod 1 year ago)
Singer Futura Quartet Seqs 6700 Sewing Machine
how to set my singer futura quartet seqs 6700 sewing machine to sew. A distance more than one inch a...
how to set my singer futura quartet seqs 6700 sewing machine to sew. A distance more than one inch a...
(Posted by johour2194 3 years ago)
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Is A Special Foot Required To Free Form Stitch On Singer Sewing Machine Model 55
(Posted by kopitkin 9 years ago)