Samsung HD503HI Support Question
Find answers below for this question about Samsung HD503HI.Question posted by uvdesai on December 27th, 2012
How To Convert The Drive To Slave Drive
The person who posted this question about this Samsung product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by bengirlxD on December 28th, 2012 9:52 AM
On the back of the hard drive.. Near the datacable. You'll see a little back/white little plastic jumper. You'll need needle-nose pliers to get it out. Carefully pull out the jumper from it's current spot and put it into the slave position It may show that to make the drive a slave drive.. Not to use any jumpers at all.. in which all you do is simply remove the jumper.
There should be a diagram on the hard drive itself to let you know where the jumper should go for the slave spot.. However. Doing this. You must make sure that you have a Master along the same datacable. Like a CD-ROM drive, or a 2nd hard drive designated as Master.. Otherwise, your computer might not function properly.
There should be a diagram on the hard drive itself to let you know where the jumper should go for the slave spot.. However. Doing this. You must make sure that you have a Master along the same datacable. Like a CD-ROM drive, or a 2nd hard drive designated as Master.. Otherwise, your computer might not function properly.
Feel free to resubmit the question if you didn't find it useful.
Samsung Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
General Support
... listed below . The form factor refers primarily to select the drive speed as in the image below . Related Article: How Can I Set The Master, Slave, Or Cable Select Jumper On My Samsung Hard Disk Drive? Most Serial ATA drives do not have jumpers setting for Master, Slave, or Cable Select. How Do I Find the Model and... -
General Support
... letter (KY5X100108) and press Register button. You can see the Convert Format menu. If you have more than one hard drive you can register the serial number later and also register again. ... the serial number when you first installed the software you want to convert to the correct hard disk drive and folder and highlight the file that you cannot use the Yepp ... -
How To Set The Jumper Setting On Your (PATA) Hard Disk Drive SAMSUNG
... Set as Master, and the other to the black connector on the middle of the drive you are installing an additional hard disk drive to a single UDMA cable with a hard disk drive Set as Slave, jumper one hard disk drive to 32 GB Clip Setting: Use this setting if you are listed below. Please verify the jumper setting...
Similar Questions
Is My Pcb The Problem With Samsung Hd503hi?
Last week I removed a piece of Ram while computer was running.Computer shut down and will not start....
Last week I removed a piece of Ram while computer was running.Computer shut down and will not start....
(Posted by pjmacdermott 7 years ago)
How To Make Samsung Sata (hd080hj/p) Hard Drive As Slave Drive
(Posted by KnaStarsl 9 years ago)
Pc Won't Boot When Samsung Hd503hi Drive Connected
trying to connect samsung hd503hi sata drive to 3 diff pc's but they all won't boot until drive remo...
trying to connect samsung hd503hi sata drive to 3 diff pc's but they all won't boot until drive remo...
(Posted by songcaludz 11 years ago)
Hd080h J/p Hard Drive Set Slave
How do you set the HDD to slave?
How do you set the HDD to slave?
(Posted by klaatujohnson 12 years ago)
Setting As Slave Drive
Hi Folks, I had a PC where the Samsung HD080HJ/P was the C: drive but after Malware cleanup it woul...
Hi Folks, I had a PC where the Samsung HD080HJ/P was the C: drive but after Malware cleanup it woul...
(Posted by chucklewis 12 years ago)