Ryobi TS1342L Support Question
Ryobi TS1342L Support Question
Find answers below for this question about Ryobi TS1342L.Need a Ryobi TS1342L manual? We have 4 online manuals for this item!
Question posted by Leggenberg on June 24th, 2011
How To Remove The Blade
The person who posted this question about this Ryobi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Ryobi TS1342L Manual Pages
English Manual - Page 1
..., ease of injury, the user must read and understand the operator's manual before using
this product. SAVE THIS MANUAL FOR FUTURE REFERENCE Compound Miter Saw
TS1342L -
English Manual - Page 3
.... Everyday eyeglasses have only impactresistant lenses, they are removed from power source.
AVOID ACCIDENTAL STARTING. Before further use of the tool, a guard or other part that keys and adjusting wrenches are not safety glasses.
SECURE WORK. Sharp blades minimize stalling and kickback.
Blade coasts after being turned off when plugging in...
English Manual - Page 4
...to secure the workpiece when possible.
BE SURE THE BLADE CLEARS THE WORKPIECE. Do not rush.
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have ...defective switches replaced by securely tightening the miter lock levers. Instructions for safe use of accessories are included with your hands and fingers for and remove...
English Manual - Page 5
... not allow familiarity (gained from the power supply and securely retighten the blade bolt.
If any part of this tool, loan them frequently and use to avoid serious personal injury.
SAVE THESE INSTRUCTIONS. f) Turn off the power switch, remove the miter saw plug from the power source and have any part...
English Manual - Page 6
...Symbol Hot Surface
Precautions that involve your hands away from the blade will result in damp locations. Failure to operate the tool better and safer.
To reduce the risk of injury or ... reduce the risk of injury, user must read and understand operator's manual before using this tool.
SYMBOLS
Some of the following symbols may be used on this product. SYMBOL
NAME
DESIGNATION/...
English Manual - Page 9
... thinner pieces. A metal piece, slightly thinner than at either end of turns completed by cutter blades when the workpiece is being dropped into the tool first. Snipe (planers) Depression made with the blade. Compound Cut A cross cut removing a wedge from the face of the work-piece to the fence.
These aids help control the...
English Manual - Page 11
... screws have been provided on the tool and in the recessed area to move the miter saw has a powerful 14 amp motor with all cuts. A blade wrench is included with the saw arm...base are for carrying the saw . Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws. Located on the compound miter saw has been provided to handle ...
English Manual - Page 12
...table.
SWITCH TRIGGER
See Figure 4. diameter may be used. TOOLS NEEDED
The following tools (not included) are needed for making adjustments or installing the blade:
Combination Wrench (2) 10 mm ,12 mm
hex key ... through the hole in .
Depress and hold the lock button while installing, changing, or removing blade. A lock with a long shackle up to 9/32 in the switch trigger. The 22...
English Manual - Page 13
..., and pull out on the lock pin.
Lift the saw has been shipped with the tool: Miter Lock Handle Dust Bag Work Clamp
DUST BAG
Blade Wrench Operator's Manual
MITER LOCK HANDLE
BLADE WRENCH
WORK CLAMP
Fig. 6
WARNING:
The use of the tie wrap.
Inspect the...
English Manual - Page 14
... after mounting to make sure the compound miter saw without checking for interference between the blade and the miter fence. Damage could result in serious personal injury. WARNING:
This saw...to accommodate the saw should be mounted to heed this tool until assembly is complete. Failure to comply could result to the blade if it strikes the miter fence during use.
Mounting ...
English Manual - Page 15
...work clamp to secure the workpiece prior to making the cut. To remove the dust bag for use a C-clamp instead of the blade guard assembly. The work clamp in the saw table base. .... ASSEMBLY
MITER LOCK HANDLE
See Figure 8. It also prevents the workpiece from creeping toward the saw blade.
Release the clips. To install the miter lock handle, place the threaded stud on the end...
English Manual - Page 16
... as shown in . Spindle Lock Button
WARNING:
If inner blade washer has been removed, replace it before reconnecting saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of oil onto inner blade washer and laser guide where they contact the blade.
WARNING:
A 10 in figure 12.
Replace laser...
English Manual - Page 17
...with using the laser guide, you have finished cutting. NEVER attempt to remove the mark.
NOTE: As the saw blade in alignment, do not move the workpiece while making a cut . ...line with light source. hd)
LASER GUIDE
Blade
SCREW
Blade
Blade BOLT cover
Inner Blade Washer
Lower blade guard
To LOOSEN
To Tighten
blade BOLT (hex. To Remove Your Mark: Position the laser ...
English Manual - Page 21
... freehand (without holding workpiece against the fence). WARNING:
NEVER move the workpiece or make you careless. Any slip can result in movement of the blade to heed this tool. A crosscut is made with the miter table set at some angle other than zero. Pull out the lock pin and lift saw...
English Manual - Page 22
... plate will seat itself in positive stop rotating before removing the workpiece from 0° to secure the workpiece when possible. Before turning on the blade at the end of a board is made . ....
Release the miter lock plate. If the concave edge of the workpiece with the blade angled to stop notches, located in the miter table frame. Tighten the miter lock ...
English Manual - Page 23
...or with a work clamp or a C-clamp to reach maximum speed.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the saw arm has...the stock firmly with one of the positive stop rotating before removing the workpiece from miter table. Once the two correct settings for the blade to secure the workpiece when possible. to obtain the desired...
English Manual - Page 24
... to secure the workpiece when possible.
Before turning on the saw blade to stop rotating before removing the workpiece from turning before raising the blade out of the cutting operation just to reach maximum speed.
Slowly lower the blade into and through the workpiece.
Release the switch trigger and allow the...
English Manual - Page 32
...attached to filter out microscopic particles.
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest...ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
• MODEL NUMBER
TS1342L
• SERIAL NUMBER
Ryobi® is a registered trademark of Ryobi Limited used under license.
...
Repair Sheet - Page 3
... 1 Torsion Spring 1 Blade Bolt 1 Laser Guide 1 Blade 1 Inner Blade Washer 1 * Screw (M4 x 9 mm, Pan Hd 1 * Screw (M5 x 10 mm, Pan Hd 4 Data Label 1 Upper Blade Guard Assembly (Inc.... 1 Spindle Lock Pin 1 E-Ring 1 Compression Spring 1 Output Spindle Assembly (Inc. MODEL NUMBER TS1342L
The model number will be found on a plate attached to the motor housing.
NUMBER
1 089100212007 ...
Repair Sheet - Page 5
... 1
31 A07003060257
* Spring Washer (M10 3
32 518104200
Pivot Support Assembly (Inc. MODEL NUMBER TS1342L
The model number will be found on a plate attached to the motor housing. Key Nos. 11... and 36-40 1
Table Spindle 1
* Cap Screw (M10 x 25 mm 2
* Blade Wrench (M35 x 115 mm 1
Operator's Manual
* Standard Hardware Item - May Be Purchased Locally COMPOUND MITER ...
Similar Questions
Dado Blade Insert For A Ryobi Rts10 Table Saw
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
(Posted by bstilton 9 years ago)
How Do I Replace The Spring On My Ts1342l 10 Lower Blade Guard
(Posted by golfesxu 10 years ago)
Lower Blade Guard Ts1342l Miter Saw
How do I replace the spring on my TS1342L 10" lower blade guard?
How do I replace the spring on my TS1342L 10" lower blade guard?
(Posted by MRELVIS 12 years ago)