Ryobi RY802800 Support Question
Ryobi RY802800 Support Question
Find answers below for this question about Ryobi RY802800.Need a Ryobi RY802800 manual? We have 4 online manuals for this item!
Question posted by faraldofernando on October 25th, 2020
Flywheel For Ryobi Ry802800
need the flywheel for a ryobi pressure washer ry802800
Current Answers
Answer #1: Posted by freginold on October 25th, 2020 3:12 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,895
Member since:
December 20th, 2011 Points: 23,253,895
The RY802800 generally uses a Honda GCV160 engine (check your serial # to be sure). The flywheel for that engine is part # 31110-ZL8-004, sold on eReplacementParts.com for $71.24.
Related Ryobi RY802800 Manual Pages
User Manual - Page 7
...away from the extension cord. The symbol may result in the cord connecting the pressure washer to the product. English This device provides additional protection from the risk of the...DOUBLE INSULATED." Failure to disconnect. WARNING:
When using this manual.
This product is needed, use . Do not direct discharge stream at all instructions listed below the level of the ...
User Manual - Page 8
... use of injury.
Check damaged parts. The smaller the gauge number, the heavier the cord. SPECIFIC SAFETY RULES
Use caution when positioning the pressure washer for use the cord to carry the product or to disconnect the plug from an outlet. Never use . Don't use product if switch does not...
User Manual - Page 9
... bolts and nuts for looseness before using the product.
Connect pressure washer only to relieve stored pressure in the high pressure hose. English These products can cause physical injuries to the operator and ...irreversible damage to the machine.
WARNING: High pressure jets can damage the surface.
After stopping the motor, always pull...
User Manual - Page 12
...receptacle end of the working outdoors with a Ground Fault Circuit Interrupter (GFCI), which eliminates the need to be performed only by Underwriter's Laboratories (UL) should be sure to use the product...it for repair. The GFCI plug can also be operated before each time you connect the pressure washer to do not protect against the hazards of power, and/or circuit breaker or GFCI ...
User Manual - Page 13
... it . The lock-out provides protection against short circuits, overloads, or shocks. n Inspect the product carefully to your cleaning project. Before use . CARRYING HANDLE
The pressure washer has a carrying handle for easy transport.
TRIGGER HANDLE
The trigger handle has a gripping surface that all operating features and safety rules.
ASSEMBLY
UNPACKING
This product...
User Manual - Page 14
... or prevent water flow to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE PRESSURE WASHER
See Figure 7. Tighten securely.
CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP
See Figure 6. n Completely uncoil and straighten the high pressure hose
to
the pump. n Turn the collar clockwise to tighten the hose securely to...
User Manual - Page 15
... for assistance. Failure to do not need to check or add lubricant to the pump before connecting garden hose. Turn on page 3. NOTICE:
Before each use . Completely unwind the hose from various exterior vertical surfaces such
as screws, nuts, bolts, caps, etc. NOTE: Make sure the pressure washer's water intake screen is turned...
User Manual - Page 16
... Nozzle Selection Guide for more information about which nozzle to operate the pressure washer. NOZZLE SELECTION GUIDE
HIGH PRESSURE
(NO SOAP WHEN USING THESE NOZZLES)
LOW PRESSURE
(FOR SOAP OR GENTLE RINSE)
Concrete, Brick, Masonry Siding, Gutters, House Fencing, Deck, Patio Lawn Equipment, Boat, RV
Turbo Nozzle
15º
Blue or Black Soap Nozzle...
User Manual - Page 17
... tank.
NOTE: The machine setting of 1 gallon pressure washer detergent without further dilution.
See the chart on the previous page for more information. n Fully unwrap and straighten hose before proceeding. Many detergents may require mixing prior to be crushed or wrapped around
objects. Use a funnel, if needed, to be kinked.
n Remove the soap...
User Manual - Page 18
...garden hose and high pressure hose.
n Remove bottle cap and attach threaded end of the unit. Point nozzle in contact with ANSI Z87.1. Lift the unit into pump. Move machine to release water pressure.
Excessive pump pressure... the threaded top.
NOTE: The rubber seal should be sure to pressure washer pump water intake.
Use of the pump protector used. Chemicals can ...
User Manual - Page 19
... paper clip or fine needle. n Turn the spray wand counterclockwise to order. Pull trigger to the
power supply. n Unplug the pressure washer. n Reinstall the garden hose and connect the unit to release water pressure. Store in a dry, covered area where the weather can't damage it from the water inlet. n Tilt the unit as shown...
User Manual - Page 20
... black soap nozzle. Replace o-ring. TROUBLESHOOTING
Problem
Pressure washer does not start when trigger is depressed
Pump doesn't produce pressure
Machine doesn't reach high pressure No detergent Wand leaks
Possible Cause
Solution
Power cord not connected to power source The on/off switch in the ON position (I).
garden hose. Add additional detergent to remove air...
User Manual - Page 21
...performance or durability or that has been operated in any obligation to all RYOBI™ brand pressure washer distributed by a RYOBI™ Authorized Service Center. The warranty does not extend to repairs ... after repair or replacement will be paid by the use of any RYOBI™ brand pressure washer without charge for warranty work must be repaired or replaced without assuming...
User Manual 2 - Page 1
... the garden hose to the pump (see page 11).
WARNING!
SWITCH OFF
Concrete, Brick, Masonry
Siding, Gutters, House
Fencing, Deck, Patio
Lawn Equipment,...finished, press switch OFF to stop the motor (see page 10).
1 Connect the pressure washer to the power supply.
PUMP PROTECTOR
Make the most of the tool plug getting wet...
Similar Questions
High Altitude Adjustment Needed For Ryi2300 Bt Inverter Generator?
Is an adjustment needed for RYI2300 BT inverter generator?
Is an adjustment needed for RYI2300 BT inverter generator?
(Posted by dani6757 4 years ago)
I Need To No What Type Of Carb Adjustment Tool I Need For A Ryobi Cs 26 Trimer
I need the carb tool for a Ryobi cs 26 what type of tool is it
I need the carb tool for a Ryobi cs 26 what type of tool is it
(Posted by poolshooter007 8 years ago)
Ryobi Ry39500
How Large Is The Gap Between Flywheel And Coil Module
(Posted by maxpac 11 years ago)
I Need Detailed Steps On How To Replace The Starte Rope On My Ryobi Model Ry1305
I need deailed steps on how to eplace the starter ropeon my Ryobi Model RY13050 edger
I need deailed steps on how to eplace the starter ropeon my Ryobi Model RY13050 edger
(Posted by alexmacc 12 years ago)