Ryobi R163K Support Question
Ryobi R163K Support Question
Find answers below for this question about Ryobi R163K.Need a Ryobi R163K manual? We have 4 online manuals for this item!
Question posted by thintim11 on August 8th, 2011
Base Plate Insert R163k
can i get an insert for this router's base plate? the hole is too large for my liking. or do they make a plate with a smaller hole?
Current Answers
Related Ryobi R163K Manual Pages
English Manual - Page 1
... rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE REFERENCE WARNING: To reduce the risk of operation, and operator safety. OPERATOR'S MANUAL
FIXED BASE ROUTER DOUBLE INSULATED
R163
Your router has been engineered and manufactured to our high standard for your purchase.
When properly cared for, it will give you for dependability, ease...
English Manual - Page 2
...cover any case, within ninety (90) days or less. warranty
RYOBI® POWER TOOL - WHAT THIS WARRANTY COVERS: This warranty covers all original equipment packaged with the following... tool, properly packaged and postage prepaid, to you.
One World Technologies, Inc. We will repair any faulty workmanship, and either request service under this product making its power tools other...
English Manual - Page 3
... all of power tool, taking into air vents.
Do not use on .
This enables better control of the power tool in the manner intended for operations different from the power tool before making any adjusting key or...heat, oil, sharp edges or moving parts. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are caused by poorly maintained power...
English Manual - Page 7
... (UL) should be performed only by a qualified service technician. Before using a power tool at a considerable distance from a power source, be used. WARNING:
The double insulated system... not need for loose or exposed wires and cut or worn insulation.
**Ampere rating (on tool data plate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16...
English Manual - Page 9
... shipping. The shield is installed on the front of the router base.
depth ADJUSTMENT KNOB
The depth adjustment knob measures changes of depth in increments of this tool provides easy handling when operating in this tool or create accessories not recommended for increased visibility.
Make sure that only one wrench is complete.
ASSEMBLY
UNPACKING
This...
English Manual - Page 10
... LEVER
ADJUSTMENT BAR TAB
SLOT IN MOTOR
TO UNLOCK
MOTOR ARROW ON MOTOR
ARROW ON BASE
Fig. 2
To install the base: n Unplug the router. Use caution as forcing may use this tool for any application, make you . See Adjustments. If movement is depressed and does not go all the way in. n Place the adjustment bar...
English Manual - Page 11
installing/REMOVING bits
See Figure 3. NOTE: Make sure that the collet always clamps the shank (non-cutting end) of control or ...the bit until the bit has come on the base of the workpiece for operation in , holding it is not securely tightened, the bit may detach during use bits which are changing a bit immediately after the router has been turned off. to rotate after use ...
English Manual - Page 12
...move the collet up or down considerably, turn off the router and reduce the depth of wood. n Loosen the lock lever.
Then, make depth adjustments with the lock lever tightened.
Note: It ...
LOCK LEVER
TO LOOSEN
Fig. 6
12 cutting diameters, are possible with 1/16 in the base. Large bits, such as veining bits with the lock lever tightened, an adjustment to the lock lever...
English Manual - Page 13
... of cut when the router is mounted to a router table, unplug the router, loosen the lock lever, turn the router on, push the switch to make through the hole in the router
table into the hole on the subbase, and place the end of cut is mounted to use router tables with the lock lever tightened. n Insert a T-handle wrench through...
English Manual - Page 14
... distances from the desired edges of the groove. Hold the router base against the guide. When routing a groove wider than the diameter of cut , turn the router off and let the bit come to use as shown in the "guide outside" illustration, tool travel should be from right to use is positioned as a guide...
English Manual - Page 16
...the tool and results in soft woods such as oak, a slower rate of the spinning bit will be used. Feed the router into new (uncut) wood. This could cause you begin.
While cutting, make sure ...
Test a cut is deep, or the workpiece is hard to the sound of kickback is a large one . If you are making cuts in . If the bit is always in a clockwise direction. A cross grain cut may ...
English Manual - Page 17
... take so large-that chips will make clean, smooth cuts if allowed to take bigger bites as it merely scrapes away sawdust-like particles. It is revolving at close to bounce off ). When the bit is scraping instead of cutting, controlling the router is an extremely high-speed tool, and will be partially knocked off...
English Manual - Page 18
...base, adjustments will slow the feed so that you complete the final pass. depth of cut requires a slower feed than 1/8 in .
To make deeper cuts, make... it is too deep will not be difficult to the tool's motor and bit. for the next pass. NOTE: ...result in the open position. A large enough bit is not likely to break, but attempting a cut can cause smaller bits to be loose enough so...
English Manual - Page 20
...plate attached to the motor housing. Be sure to these chemicals are specially designed to filter out microscopic particles.
• SERVICE
Now that are : • lead from lead-based...those dust masks that you have purchased your tool, should a need ever exist for repair ...2579 www.ryobitools.com
20 OPERATOR'S MANUAL
FIXED BASE ROUTER DOUBLE INSULATED
R163
WARNING:
Some dust created ...
Repair Sheet - Page 1
R163 REPAIR SHEET RYOBI DOUBLE INSULATED FIXED BASE ROUTER
MODEL NO.
Repair Sheet - Page 2
MODEL NUMBER R163 19 18
20
21 6 4 7
3 2 1
17
16
15 14
12
10
13 11
8
9
6
5 4
RYOBI FIXED BASE ROUTER -
Repair Sheet - Page 3
...
21
671758001
22
900987001
983000958
06-18-07 (REV:02)
Screw (10-32 x 1/4 in 4 Subbase Assembly 1 Chip Shield 1 Screw (#8-10 x 5/8 in all correspondence regarding your ROUTER or when ordering repair parts.
Philips Pan Hd 4 Right Handle Assembly 1 Screw (#10-24 x 9/16 in. Torx Recess Pan Hd 2 Left Handle Assembly 1 Hex Lock...
Repair Sheet - Page 4
MODEL NUMBER R163 15 31
25 24 23
30 18
28
27 26
29
12
22
25
24
23
21
8
6
20
17 16 13
14 32
13
11 10
9 7
33
5
19
4 3 2
1
SECTION "A"
RYOBI FIXED BASE ROUTER -
Repair Sheet - Page 5
...represents an important part of alteration or damage to the system, service should be found on a plate attached to the motor housing. Pan Hd 1 Upper Cap Assembly (Inc. NUMBER
DESCRIPTION
QTY.
1...940999110
33
671250001
Screw (8-18 x 24 Pan Hd 4 Screw (M3.5 x 14.5 Pan Hd 1 Router Base/Spindle Lock Actuator Kit (Included With Key 13 On Pages 2-3 1 Torsion Spring 1 Bearing Frame 1 Ball...
Repair Sheet - Page 6
RYOBI FIXED BASE ROUTER - MODEL NUMBER R163
POWER CORD
WHITE LEAD
BLACK LEAD
PCB ASSEMBLY RED LEAD
MOTOR
SWITCH BROWN LEAD
WHITE LEAD
BROWN LEAD
BLACK LEAD
BRUSH ASSEMBLY
WIRING DIAGRAM
Similar Questions
How To I Attach A Base Plate In Order To Install Bushings?
Looking to install a base plate to the bottom of the router so that I can attach a bushing to do inl...
Looking to install a base plate to the bottom of the router so that I can attach a bushing to do inl...
(Posted by Christopherfontaine 1 year ago)
What Size Screws Are Needed To Attach The Ryobi Re180pl1 To A Table?
i bought my Ryobi RE180-PL1 as a display model at a Home Depot store closing sale so it was missing ...
i bought my Ryobi RE180-PL1 as a display model at a Home Depot store closing sale so it was missing ...
(Posted by mjohnroussel 9 years ago)
Is There A 1 3/16 Base Plate Available For The Re180pl1 Plunge Router
(Posted by russhanks 11 years ago)
Ryobi R163 And The Ryobi R163k Routers
What is the difference between the Ryobi R163 and the Ryobi R163K routers?
What is the difference between the Ryobi R163 and the Ryobi R163K routers?
(Posted by chchls3 11 years ago)
Where Do I Find A Insert For The Base
I need the base plate insert for this router.
I need the base plate insert for this router.
(Posted by squeaky38 12 years ago)