Ryobi P782 Support Question
Ryobi P782 Support Question
Find answers below for this question about Ryobi P782.Need a Ryobi P782 manual? We have 1 online manual for this item!
Question posted by Jolynndel87 on September 10th, 2021
Broken?
it's was outside and got wet from the rain. Not a lot of rain. Let it dry out and it won't work. Any suggestions
Current Answers
Answer #1: Posted by Technoprince123 on September 11th, 2021 4:19 AM
Technoprince123
Member since:
February 8th, 2021 Points: 1,205,190
Member since:
February 8th, 2021 Points: 1,205,190
https://www.ryobitools.com/products/details/33287179206
https://www.homedepot.ca/product/ryobi-18v-one-hybrid-tripod-stand-light/1001598911
Please response if this answer is acceptable and solw your problem thanks
Answer #2: Posted by SonuKumar on September 11th, 2021 2:22 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
Not issue, ideally leave in sun for about 2-3 days or with hot bowler blow for about 20-30 min.
good luck !!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #3: Posted by hzplj9 on September 11th, 2021 10:51 AM
hzplj9
Member since:
June 25th, 2012 Points: 4,874,710
Member since:
June 25th, 2012 Points: 4,874,710
Check if there is a fuse in the plug. If there is it is likely to have blown when you plugged it in after the drying period when there may have been some water left around. Check the wiring to the unit for a corroded connection as water damage will go bad when subjected to an influx of water. It may look OK but check the wiring.
Good luck.
Related Ryobi P782 Manual Pages
Operation Manual - Page 2
... temperature is severely damaged or completely worn out. Do not store in outside sheds or in vehicles.
Do not permit children to use light, lens, and surrounding housing.
Keep light dry, clean, and free from wet conditions.
When transporting the light in a vehicle, securely tie it can fall or be followed, including the...
Operation Manual - Page 3
... not crush, drop or damage battery pack. SAVE THESE INSTRUCTIONS
3 - SAFETY RULES FOR LIGHT
Always remove battery pack before storing the device.
To reduce the risk of injury, do not charge the battery pack or appliance outside of the specified range may damage the battery and increase the risk of...
Operation Manual - Page 4
... debris and chemicals.
When using an extension cord outdoors, the extension cord should be kept dry and off ("O") position, then remove plug from heat, oil, sharp edges, and rotating ...avoid serious personal injury, never allow the work light to avoid possible pinching.
Battery tools do not use one heavy enough to water or rain. n To disconnect, turn all controls to...
Operation Manual - Page 5
... use alternating current, connect the product to your nearest authorized service center for outside use an extension cord that is designed for repair. English ELECTRICAL
DOUBLE INSULATION
Double... - All exposed metal parts are working area. Double insulated products do so can result in the product's internal wiring.
For service, we suggest you are isolated from a break in...
Operation Manual - Page 6
Read Operator's Manual
Wet Conditions Alert
Wet Conditions Alert
Electric Shock
To reduce the risk of injury, user must read and ...do not use in damp locations. NOTICE:
(Without Safety Alert Symbol) Indicates information considered important, but not related to rain or damp locations. Some of the following signal words and meanings are intended to explain the levels of risk associated ...
Operation Manual - Page 7
... and completely assembled or with tools to inflict serious injury. Staring into the light beam may use any parts are damaged or missing, please call 1-800-525...light beam at persons or animals and do not stare into the product as described in serious personal injury. FEATURES FEATURES
PRODUCT SPECIFICATIONS
Maximum Height 5 ft.
OPERATION
WARNING:
To reduce the risk of most work...
Operation Manual - Page 9
... when positioning work light to replace ...light is installed, this indicates a low charge condition. Failure to damage from combustible materials. GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are always in serious personal injury.
NOTE: ILLUSTRATIONS BEGIN ON PAGE 10 FOLLOWING FRENCH AND SPANISH LANGUAGE SECTIONS.
9 -
If wrapped or in a dry...
Similar Questions
Brad Nailer Stopped Working After It Got Wet
what could be wrong with my ryobi Brad nailer after it got wet I put battery on it smoked and now wo...
what could be wrong with my ryobi Brad nailer after it got wet I put battery on it smoked and now wo...
(Posted by Dacat1188 1 year ago)
Power On/off
unit will not turn on (both light and air pressure pump) even though it is connected to the proper w...
unit will not turn on (both light and air pressure pump) even though it is connected to the proper w...
(Posted by jimbocinsky 3 years ago)
The Light Will Flash And The Product Will Not Charge After It Has Been Plugged
in for 30 hours. The behavior does follow the rules as stated on page 9 and the product has previous...
in for 30 hours. The behavior does follow the rules as stated on page 9 and the product has previous...
(Posted by bjp4005 8 years ago)
What Does A Flashing Red Light Mean When The Inflator Is In Off Position.
This product will not charge even when plugged in to an electrical outlet.
This product will not charge even when plugged in to an electrical outlet.
(Posted by bjp4005 8 years ago)