Rheem P-M206 Support Question
Find answers below for this question about Rheem P-M206.Need a Rheem P-M206 manual? We have 3 online manuals for this item!
Question posted by richardwaterfall on April 14th, 2014
Pool Heater P-m206
Is this heater a Versa P-M206 or a Rheem P-M206? I have been quoted this unit to heat a 27x13x4 pool with 29,000 litres of water. Is it the correct unit to do the job?
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Rheem P-M206 Manual Pages
Brochure - Page 2
...to -pilot ignition system. Rheem Digital gas heateR
Microprocessor-Controlled Thermostat
Sp a S e t 104F Heating
The Rheem Digital gas heater is equipped with a robust flame signal. Self-Diagnostic
Sp a S e t 104F Se n s o r Fa i l u r e
Troubleshooting a Rheem gas heater has never been easier. Multi-unit installations can easily be integrated into the pool control system of line test...
Brochure - Page 3
...Nickel Fin Tube
Rheem heaters are available with its ability to protect against aggressive water chemistry, which...heat efficiently, and is an excellent choice for details).
The D-2 Power Vent is approximately 50% thicker. MKG-15-1503 Effective 10-01-2011 For dimensions and technical specifications,
see D-2 Power Vent manual for pool and spa heater heat exchangers, where the water...
Operating Instructions - Page 1
...future reference.
WHAT TO DO IF YOU SMELL GAS: • Do not try to the heater or in legible condition and kept adjacent to light any appliance. • Do not touch ...: 08-25-11
Replaces: 04-26-11
P/N 241236 Rev. 25
INSTALLATION & OPERATING INSTRUCTIONS
Gas-Fired Pool & Spa Heater
Atmospheric Models 206A, 266A, 336A & 406A
Lo NOx Models 207A, 267A, 337A & 407A
WARNING: If...
Operating Instructions - Page 2
... of the pool or spa water should be obtained from your pool or spa builder, accredited pool shop, or chemical supplier for the correct levels for balanced water. The following : Changes to 3
Total Dissolved Solids (PPM) 3000 MAXIMUM** 3000 MAXIMUM** 3000 MAXIMUM**
* Free Chlorine MUST NOT EXCEED 5 PPM! ** In salt water chlorinated pools, the total TDS can damage your heater, and...
Operating Instructions - Page 3
...Pool & Spa Water Chemistry
38 Time Clock / Fireman's Switch
8
Automatic Chlorinators & Chemical Feeders 38 Water Pressure Switch
9
Cold Weather Operation
38 Flame Roll-Out Safety Switch
9
Winterizing the Pool & Spa Heater...21 Heat Exchanger Pressure Drop Tables
TROUBLESHOOTING
22 Polymer Headers
43 Mechanical
22 Cast Iron Headers
44 Electrical - Millivolt (Mechanical Therm.)
29 Wiring...
Operating Instructions - Page 4
... is operating.
4 ON OFF
If your heater has been installed correctly, operating the heater is filled with millivolt or electronic ignition. BEFORE START-UP
BURNERS
Clean main burners, combustion fan (if equipped) and air louvers of safe and reliable pool/spa water heating. WATER
Water must be flowing through the heater during operation. ASME-certified units, typically used in the Control...
Operating Instructions - Page 7
....
CAUTION
MAIN BURNER FLAME
Elevated water temperature can cause drowsiness which induce drowsiness, such as 4°F (2.2°C).
5. Pregnant women should be blue with an accurate thermometer; spa or hot tub thermostats may err in the birth of alcoholic beverages before using pools or hot tubs.
6. Refer to the heater is considered safe for a healthy...
Operating Instructions - Page 8
... of the burner and pilot flames. Should the latter occur, shut the heater off .
POOL & SPA WATER CHEMISTRY
Chemical imbalance can cause severe damage to cleaning.
AUTOMATIC CHLORINATORS AND CHEMICAL... Lo NOx burners and orifice areas should be contaminated by the warranty. Heat exchanger damage resulting from combustible materials, gasoline and other flammable and corrosive vapors...
Operating Instructions - Page 9
... be required. Remove the heat exchanger inspection panel on the side opposite water piping to gain access to the drain plug on the inlet/outlet header, (under water pipes). Open drain plug on return header.
When temperatures are reached. COLD WEATHER OPERATION
WINTERIZING THE POOL & SPA HEATER
IMPORTANT FREEZE INFORMATION
MODERATE CLIMATE: Heater operation can seriously damage...
Operating Instructions - Page 10
... the heater from ...(2)
8. Plastic pipe finish flange for the equipment. Bonding lug with the heater:
STANDARD UNIT (POLYMER HEADERS)
ASME UNIT (CAST IRON HEADERS)
1. The Model & Serial No. "Pagoda" top...2" flange gaskets (2)
(AFT models only)
5. Located on the Bill of the heater. RECEIVING EQUIPMENT
The manufacturer recommends that you receive the number of packages indicated on ...
Operating Instructions - Page 11
...2,000 feet elevation. IMPORTANT NOTICE These instructions are suitable for Gas-Fired Pool Heaters.
When such locations cannot be avoided, it is such, be located in an area where possible water ...of airborne dust and airborne fiber particles. When removing the burners or heat exchangers, take precautions to the structure. The appropriate top designated for Canada, the latest...
Operating Instructions - Page 12
Alcove (Open) Right Side - 12" (Water Side)
Vent - 6"
Left Side - 6"
Floor** - 0"
(Opposite Water Side)
OUTDOOR INSTALLATION:
Top* - When installed according to the listed minimum clearances from combustible construction, the pool heater can still be serviced without removing any structure around the heater. In either the heat exchanger or the burner tray.
WARNING: Do not install ...
Operating Instructions - Page 13
...pool heaters shall not be installed with the top of the vent assembly within 10 ft below , 4 ft horizontally from, or 1 ft above any forced air inlet, or intake ducts located within 10 ft horizontally. For U.S.
Roof water...installation of hurricane tie-down brackets for all models.
13
The top surface of the heater shall be a minimum of 4 ft below , or to the latest revisions of CAN...
Operating Instructions - Page 24
... it to the pool or spa must be connected to maintain set-point, the heater will then display sensed water temperatures downstream of the primary heating system, rather than the temperature of the water exiting the pool. If the primary system provides adequate heat to the main line ahead of the heater; Heater must not have any water leaks will not...
Operating Instructions - Page 27
... Electrical Code, ANSI/NFPA 70. (Canada - Connect the white wire to the white wire. For Lo NOx pool heaters attach a wire nut to each white wire independently. It is turned off.
27 See pages 36-38. If...RED
240 VAC WIRING For 240 VAC input power to the unit, connect the black wire to the heater from the GFCI power source. For Lo NOx pool heaters attach a wire nut to the "L2" or second hot...
Operating Instructions - Page 33
..."Heating."
Temp Buttons If the heater is used to ten faults in POOL or SPA mode, the desired water temperature (SETPOINT) will alternate with the desired water ...HEATING Service Menu and Fault History To access the Service Menu and fault history, press the MODE and UP buttons simultaneously for possible causes and corrections. Normal readings range from 24 to 5 seconds. When the water...
Operating Instructions - Page 38
... to check). MAX
POOL OR SPA
5 FT. MAX
NOTE: If heater is installed outside of total wiring using 18 AWG stranded copper wire rated for heat again. 7. This is equipped with two automatic high limits. HIGH LIMITS The heater is a "single-use a multimeter to adjust the water pressure switch, utilize the following procedure:
WATER PRESSURE SWITCH ADJUSTMENT...
Operating Instructions - Page 41
... applicable codes. LO NOx POOL HEATERS
The Lo NOx pool heaters are equipped with a thermal cut-off device to prevent flame roll-out in hot water (over -temperature conditions have been fixed.
Set controller to disable the heater. Once the blower provides pressure, the main gas valve will operate until call for heat, the ignition system, consisting...
Operating Instructions - Page 43
...Replace fan relay.
Takes too long to heater sizing chart. Replace pilot. output(BTUH)
Pool gallonage x 8.33 or refer to heat pool or spa
Under-sized heater
Filter not running long enough Dirty filter Gas line or meter undersized
Calculate heating capacity of heat exchanger.. If no movement, replace. Raise water level.
Replace refractory panels. Replace air switch...
Warranty - Page 2
...PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. We suggest you . KEEP IT WITH YOUR POOL HEATER OR BUSINESS RECORDS. This warranty is VOID if the product is not available please contact warranty service at its factory.... FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING NO LIABILITY FOR DAMAGE FROM WATER LEAKAGE) WHICH ARE EXPRESSLY EXCLUDED.
Similar Questions
P-m266a-en-x Pool Heater Water Switch Open Error Message.
how do I adjust/replace or reset the water pressure switch on the pool heater. The manual included w...
how do I adjust/replace or reset the water pressure switch on the pool heater. The manual included w...
(Posted by pricerd 2 years ago)
Is Control Bezel Same As Board?
Our display is failing on our M206 and we can barely read it but it appears to same Board Failure. I...
Our display is failing on our M206 and we can barely read it but it appears to same Board Failure. I...
(Posted by blueprint2911 2 years ago)
Parts
where can I get part sp20296 for a Rheem 50 Gal poervent waterheater in Colorado Springs, Colorado
where can I get part sp20296 for a Rheem 50 Gal poervent waterheater in Colorado Springs, Colorado
(Posted by bbundyis 7 years ago)