RedMax BCZ2460TS Support Question
RedMax BCZ2460TS Support Question
Find answers below for this question about RedMax BCZ2460TS.Need a RedMax BCZ2460TS manual? We have 1 online manual for this item!
Question posted by isad1 on November 10th, 2017
Oil In Spark Plug
my trimmer wont start i took out spark plug and it had oil all over i clean it and this time it tried to run for a few seconds and shot off remove spark plug again and it was full of oil what do i need to do to get it running again
Current Answers
Related RedMax BCZ2460TS Manual Pages
Owners Manual - Page 1
This spark ignition system complies with the Canadian standard ICES-002. BCZ2460S/TS 115 35 57-10 (006)
U S
OWNER'S/OPERATOR'S MANUAL BRUSHCUTTERS
BCZ2460S BCZ2460TS
WARNING
The engine exhaust from this manual carefully to cause cancer, birth defects or other reproductive harm.
US-1
WARNING
Before using our products, please read ...
Owners Manual - Page 3
...-1(rpm) Idle speed 3000 ± 200/min-1(rpm) Fuel Mixture (Gasoline 50 : Oil 1)
(when using RedMax genuine oil) Carburetor Walbro Diaphragm type Spark plug NGK CMR7H Fuel tank capacity 21.3 fl.oz (0.63 ) Transmission Centrifugal clutch, Rigid driveshaft Reduction ratio BCZ2460S 1.462 BCZ2460TS 2.1 Cutting head rotating direction Counter-clockwise(Operator view) Durability period 300 hrs...
Owners Manual - Page 4
... CONTROL An emission control label is located on the engine. EMISSION CONTROL INFORMATION
THIS ENGINE MEETS U.S. MANUFACTURED: USE JASO FD OR ISO L-EGD GRADE 50:1 OIL
*1: The year will be changed every year of manufacturing. *3: SP : Sealed tank made of thrown objects. (5) Warning/Attention (6) Keep all children, bystanders and helpers 15...
Owners Manual - Page 5
...time over which no circumstances may interfere with
the inhalation of the working manner (See p5), Repetitive Stress Injury(RSI) could occur. Also try...-5 For safe operation
WARNING
• A brushcutter or trimmer can result in serious personal injury or the death of... time, or working area.
To reduce the risk of anti-slip
protection to ensure safety.
6. Never start or run ...
Owners Manual - Page 6
... When starting the engine, check to touch the muffler, spark plug, other Warn adults to perform cutting work .
■ Starting the engine 1. Each time before starting the ...spark plug or plug cord
while the engine is moved fully back to avoid any obstacle before installing or removing attachments. If any obstacle when the engine starts. If the cutting head is started...
Owners Manual - Page 7
...oil or fuel mixture. 7. Do not smoke while handling fuel or while operating the product. 4. Keep the handles dry, clean and free of sparks...spark plug before
transporting or storing the product. 2. Use special care around the fuel line, the
US-7 When hand-carrying the product, cover
over the cutting part, lift up all times...; Storage 1. Do not refuel a running engine. 6. Wipe up the product...
Owners Manual - Page 8
... have been certified by RedMax for use any accessory or attachment other part, or
any lubricant, always be sure to allow your machine, fuel or oil for the machine, be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for the unit. 7. Do not use with the RedMax...
Owners Manual - Page 9
Push the driveshaft housing toward the
clutch housing and rotate it bottoms, and align the positioning holes on the gear box, loosen
and remove the hexagon nut(left- Remove the air cleaner cover. 2.
Fit the line head assembly to
the joint on the top of the carburetor. (SE2)
■ CONNECTING SWITCH WIRES •...
Owners Manual - Page 10
... starting ...sparks near fuel.
RedMax Air-Cooled "Max Life", Synthetic blend Premium two stroke engine oil and ISO-L-EGD (ISO/CD1378) AND JASO-FD oils...parameters and components (eq., carburation, ignition timing
and port timing) without addition of alternative fuels will be...gasolines or oils may contain maximum of
Minimum
89
Octane
[
R+M 2
]
(Mid
grade
or
Premium)
clean gasoline. ...
Owners Manual - Page 11
...60 days.
■ FOR YOUR ENGINE LIFE, AVOID 1. FUEL WITH NO OIL (RAW GASOLINE) - It can cause spark plug
fouling, exhaust port blocking, or piston ring seizure. 4. It can cause ...Start the engine and run the carburetor dry residual fuel. 6. In the case of the container to limit the entry of time,
RECOMMENDED MIXING RATIO GASOLINE 50 : OIL 1 (when using RedMax Air-Cooled "Max Life")
clean...
Owners Manual - Page 12
...or remove the spark plug and dry it by releasing the knob. Allow the engine to start rotating upon the engine starts....starting of the engine.
2.
Shift the stop switch (2) RUN (3) STOP
(a) lockout lever (b) throttle trigger
OP6
5. OP3
(3) (2)
4. Operation
OP1
■ STARTING ENGINE
WARNING
The cutting head will start due to the "STOP"
position. Release the throttle lever and run...
Owners Manual - Page 13
...inch(25.4 mm). For better effect, tap the head on the ground while running the engine at full throttle. • Each time the head is operated. Operation
OP7
■ CUTTING WORK (LINE HEAD USAGE)...thrown into the cutting area. The rate of cutting motion will light growth.
4. Try to trim at all times when the unit is bumped, the line advance about 20 degrees toward the sweep direction...
Owners Manual - Page 14
... cool before use
wipe out
✔
inspect/clean
✔
see ■ADJUSTING IDLING SPEED (p.12)
✔
clean and readjust plug gap
clean
clean
check operation
✔
replace if something's wrong...fuel tank, air filter, fuel filter idle adjusting screw
spark plug cylinder fins, intake air cooling vent muffler, spark arrester, cylinder exhaust port throttle trigger, stop switch ...
Owners Manual - Page 15
...
(1)
MA4
.026 in 0.65 mm
■ SPARK PLUG • Starting failure and mis-firing are lubricated by
multipurpose, lithium-based grease in a personal injury. For a replacement plug, use or more with moving cutting head or hot muffler may result
in the engine catching on the job condition. • Remove the side bolt in the correct...
Owners Manual - Page 16
...is necessary to remove the engine cover shown in (MA7) in between the cylinder fins, it away using oil-free, lead-free gasoline.
• Aged fuel is clean and free of engine starting failure. US-...BE PERFORMED AFTER EVERY 100 HOURS OF USE
1. Before storing the unit, empty the fuel tank and run the engine until it uses all screws, bolts, and fittings. 3. Note that this in turn ...
Owners Manual - Page 17
... strap. (OPT1 - OPT5
(1) (2)
(3) (4)
(5) (6)
(7)
OPT2 OPT3 OPT4
(A)
(1) Shoulder strap
(2) Guard
(B)
(3) J-handle
(4) Bracket ASSY
(C)
(5) Cover
(6) Holder (B)
(D)
IMPORTANT
Change to prevent injury. Put on this • When sharpening, removing, or reattaching the blade, be sure to use
and equipment to the debris guard which
have been certified by RedMax.
Owners Manual - Page 18
...b) Guide the blade from your right to left end to stop before checking the blade, and removing any error to the blade, discard it cannot cut grass. Adjust the strap length so that ... unit and the blade can help eliminate the element of the body.
2. Optional blade usage
■ STARTING THE ENGINE Please refer 5.For safe operation (P.6), 8.Operation (P.12). Cut fibrous weeds and grass only. ...
Owners Manual - Page 20
US-20 Engine starts but does not keep running/Hard re-starting. BCZ2460S/TS
13.
Starting failure CHECK
fuel tank fuel filter carburetor adjustment screw sparking (no spark)
spark plug
PROBABLE CAUSES ➞ incorrect fuel ➞ fuel filter is clogged ➞ out of normal range
➞
muffler,cylinder (exhaust port) ➞ carbon is incorrect ➞ ...
Owners Manual - Page 21
... to you have any warranted part under the warranty must be completed in a reasonable amount of time, not to the owner at [email protected].
If you including
diagnosis, parts and labor. ...type of use , that you warranty coverage if your equipment is warranted for the period of time prior to ensure the performance of two years. Also, included may deny you retain all applicable ...
Similar Questions
Bar And Chain Oil Leak.
All of the bar and chain oil leaks from my G5300 when not in use. It seems to be coming from the pum...
All of the bar and chain oil leaks from my G5300 when not in use. It seems to be coming from the pum...
(Posted by ferndog5700 6 years ago)
Getting The Hb281 To Stay Running?2012 Model.
I have already tried rrebuilding the carberater. Now. It does start, but only for a few seconds. The...
I have already tried rrebuilding the carberater. Now. It does start, but only for a few seconds. The...
(Posted by 64bobbydriscoll 8 years ago)
Head Gasket Replacement And Oil Leak Problem.
Do I have to remove the entire head to replace the gasket? Also what may cause oil leak from air int...
Do I have to remove the entire head to replace the gasket? Also what may cause oil leak from air int...
(Posted by slipknot627 8 years ago)
How To Troubleshoot Redmax Recoil Assembly?
I replaced the recoil assembly on two redmax bc2600 trimmers. One starts great. The other one, the r...
I replaced the recoil assembly on two redmax bc2600 trimmers. One starts great. The other one, the r...
(Posted by Anonymous-145219 9 years ago)