RCA ANT702F Support Question
RCA ANT702F Support Question
Find answers below for this question about RCA ANT702F.Need a RCA ANT702F manual? We have 1 online manual for this item!
Question posted by edlepera on July 16th, 2016
Grounding The Rca. Ant702f That Is Outside
The ANT702F is mounted outside on a electrical conduit 2 inch PVC pipe. The manual doesn't mention a thing about grounding The PVC pipe so attached with plastic mountings to a wood board Where should I run the grounding cable off of? The antenna metal u bolt ?
Current Answers
Answer #1: Posted by TommyKervz on July 19th, 2016 8:40 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Hello: If the manual is not able to help during installation' please contact RCA support for installation assistance [email protected] USA' click here if you are not in USA.
Related RCA ANT702F Manual Pages
User Guide - Page 1
... Antenna
• Amplifier Insert
• Power Adapter
• Mounting Base
• Mounting Arm
• Hardware bag:
(2) U-Bolts
(2) Clamps
(4) Plastic Anchors
(4) Wood screws
(4) Washer Nuts
(1) Coaxial cable
... authority to Part 15 of the FCC Rules. ENGLISH
ANT702F Digital Amplified Indoor/Outdoor Antenna
User's Guide
FCC Statement This device complies with part ...
User Guide - Page 2
Mounting the Antenna
The antenna mounting base and arm give you mount the antenna, consider the following factors in reception performance: • The antenna performs best when mounted vertically • The antenna should be mounted on any metal surface, including aluminum siding. The antenna can be mounted in an attic or indoors.
2 never attach foreign objects to see the locations of ...
User Guide - Page 3
... against the concrete surface and secure it using the four wood screws provided. continues on next page...
3
You'll need to concrete, brick, or drywall... ENGLISH
Mounting to the surface. Do not overtighten these screws, attach the base to mount the antenna.
• Set the base aside and drill a 0.1575" pilot hole at each hole...
User Guide - Page 4
...the arm. Find one of the bolts included in the base's mounting well. Tighten the bolt to attach the arm to the antenna.
4 Then position the arm over the other side of the ...the bolt in this package. Tighten the bolt to attach the arm to the base.
3. Then position the arm over the other bolt included in the antenna's mounting well. First, set the bolt in this package. ...
User Guide - Page 5
... U-bolts. Cover the connector with this package.
Mounting to the desired position. 3. Move the arm or antenna to a Mast
1.
IMPORTANT: If you 're using the coaxial cable that the antenna and arm stay firmly in this antenna, skip step 1. To adjust the antenna's position: 1. Find the coaxial cable and one of the U-bolts included in
position...
User Guide - Page 6
... base to the mast.
3. Instead, leave it outside the U-bolt and tape it under the U-bolt. Position the antenna base as high as shown here. Note: If you used the provided coaxial cable, make sure to the base. 2. If you want. Attach the clamp assemblies to mount the base so that came with this package...
User Guide - Page 7
... antenna's mounting well. First, set the bolt in this antenna.This cable was designed to the mast. 5. First, set the bolt in this package. continues on next page... 7 Tighten the bolt to attach the arm to the arm. Find one of the well. Tighten the bolt to attach the arm to the base. Instead, leave it outside...
User Guide - Page 8
... the attached weather boot. If you 're using a different cable, DO NOT pass it to affix it under the U-bolt. To adjust the antenna's position: 1. Try different positions for best performance.
90°
Important: These diagrams show the cable that the antenna and arm stay firmly in
position.
6. Instead, leave it outside of the mounting...
User Guide - Page 9
... should set . Scan for multiple TVs) and LOW if the antenna is outside (or if you're using it into a standard AC outlet. Note: If you want to HI ...cable on the amplifier insert to the antenna input jack on the amplifier to Your TV
TO TV
HI LOW TO ANT
+12 VDC
Coaxial Cable
Ampli er Insert
TV
1.
Run the coaxial cable from the antenna, connect the short coaxial cable...
User Guide - Page 10
... or silicone caulking (not included). An "F" connector wall plate can typically find an "F" connector wall plate at any local electronics or hardware store.
10 Run the coaxial cable approximately six inches below the wall entry point and then turn it upwards towards this spot. You should seal the point where the...
User Guide - Page 11
...province. This Warranty is not transferable and does not cover product purchased, serviced or used outside the United States or Canada. Do not return this product to costs incurred for parts ... L5T 3A5
©2013 VOXX Accessories Corporation 3502 Woodview Trace, Suite 220, Indianapolis, IN 46268
ANT702F NA IB 01
11
This Warranty does not apply to the Retailer.
Some states/provinces do not...
RCA Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Installing Terk FDTV1A Amplified Flat Indoor Television Antenna
... should be plugged in the manual that is turned off . How do not, try connecting without the amplifier. Plug the amplifier's power cord into an electrical outlet. For most situations, so try as much as a cable box or satellite receiver). Run your local broadcasts are three options for standing the antenna upright. Connecting the FDTV1A... -
Installing Terk FDTVO Digital Flat Outdoor Amplified Antenna
.... Attach the antenna to complete installation. Then position the arm over the other connections are two screws. You can be plugged in mounting the antenna. Insert each U-bolt as shown. Skip to the Connecting the FDTVO to a TV section to the arm. Connect the RG6 coaxial cable the ANT jack on a metal surface will be mounted on the antenna... -
Installing the RCA ANT800 Outdoor Antenna
... it into the base as shown bellow. Mounting on the end of each U-bolt into a standard AC outlet. Then position the arm over the other side of the well. Find the other screw, washer and nut. Mounting the Antenna. Run the coaxial cable approximately six inches below . The ANT800 can rotate the antenna on the arm. First set .
Similar Questions
My Rca 702f Antenna Stopped Working
my antenna was working fine and it stopped working today. What could be the problem
my antenna was working fine and it stopped working today. What could be the problem
(Posted by JamesBradburnjb 8 years ago)
In Line Amplifier To Boost Weal Signals On A Rca Ant702f Antenna
Where to install the in line amplifier on a Rca Ant702 f antenna, before the spliter or after
Where to install the in line amplifier on a Rca Ant702 f antenna, before the spliter or after
(Posted by johnstineman49 9 years ago)
Rca Ant702f Can Using Outdoor Can Not Find Local Sd Stations?
Only two stations for HD testing are available KVSDHD and KVSD. NO real TV program such as news. WHY...
Only two stations for HD testing are available KVSDHD and KVSD. NO real TV program such as news. WHY...
(Posted by SHEENALIU 9 years ago)
Hi: I Have A Flat Dtv Indoor Antenna, Do I Need To Have It Grounded In The Roof?
(Posted by wallymorales 10 years ago)
Where Does The Ground-wire Mount On This Antenna?
Where does the ground-wire mount on this antenna? Model: RCA ANT3036XR
Where does the ground-wire mount on this antenna? Model: RCA ANT3036XR
(Posted by RVMacys 11 years ago)