Poulan PBGT2254 Support Question
Poulan PBGT2254 Support Question
Find answers below for this question about Poulan PBGT2254.Need a Poulan PBGT2254 manual? We have 1 online manual for this item!
Current Answers
Related Poulan PBGT2254 Manual Pages
User Manual - Page 1
Failure to do so can result in U.S.A. ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com
194604 10.19.04 RD Printed in serious injury.
IMPORTANT MANUAL
Do Not Throw Away
02139
OPERATOR'S MANUAL
MODEL:
PBGT2254
LAWN TRACTOR
WARNING:
Read this Manual and follow all Warnings and Safety Instructions.
User Manual - Page 7
...is reached which allows you to 1st gear.
• Slowly release clutch/brake pedal and slowly drive tractor off the skid. Be sure the area in front of tractor is positioned over large ...lever to remove the tractor from top. ADJUSTMENT
02464
KNOB
FIG. 3
NOTE: You may now roll or drive your tractor off skid.
• Apply brake to stop tractor, set parking brake and place gearshift lever...
User Manual - Page 8
...
"A" BRACKET RETAINER SPRING
"B" BRACKET
NOSE ROLLER
FIG. 6
INSTALL MOWER AND DRIVE BELT (Sees Fig. 7 and 8)
See MOWER AND DRIVE BELT ASSEMBLY Supplement Sheet for proper routing in all the way.
ASSEMBLY
TO ATTACH...; Go to the right.
• Remove plastic tie strap from mower belt and check belt for additional guidance on level surface and mower suspension arms are positioned in ...
User Manual - Page 9
... at the factory).
✓ Be sure mower deck is adjusted comfortably and tightened securely.
✓ All tires are shown for leveling).
✓ Check mower and drive belts. Operate them before operating mower as shown
in this manual. CHECK BRAKE SYSTEM
After you learn how to operate your tractor were overinflated...
User Manual - Page 12
... conditions, height of grass and types of grass being mowed.
• The average lawn should be mowed twice.
ment. FAILURE TO DO SO WILL SHORTEN THE USEFUL LIFE OF...OUT TO "ENGAGE"
"BRAKE"
02146
POSITION
IGNITION KEY
PARKING BRAKE
"ENGAGED"
CLUTCH/
POSITION
BRAKE PEDAL
"DRIVE"
HEIGHT
"DISENGAGED"
POSITION
ADJUSTMENT POSITION
KNOB
GEAR SHIFT LEVER
FIG. 9
STOPPING (See Fig. 9)
...
User Manual - Page 13
...are properly adjusted when they are in place.
02828
TO OPERATE ON HILLS
CAUTION: Do not drive up or down hills with an operator presence sensing switch. Raise gauge wheels slightly to prevent ...will shut off the ground when mower is equipped with slopes greater than 15° and do not drive across any slope.
• •
13
Choose the slowest speed before backing.
• Move ...
User Manual - Page 14
... the engine and let it run until "FULL" mark on dipstick is reached. Use fresh fuel next season.
this manual.
• The attachments and ground drive can now be sure gearshift lever is in neutral (N) position.
• Move attachment clutch to "DISENGAGED" position.
• Move throttle control to fast position
•...
User Manual - Page 15
... mower housing is wet. OPERATION
• The attachments can be used during the engine warmup period and may need to be adjusted for trimming.
• Drive so that clippings are discharged onto the area that has been cut desired. • When operating attachments, select a ground speed that clippings will discharge away...
User Manual - Page 16
... the spark plug,
clean or replace air filter, and check blades and belts for wear. To receive full value from the warranty, operator must maintain tractor as...Battery Level
R Clean Battery and Terminals
Check Transaxle Cooling
Check V-Belts
BEFOREEEVAECRHYU8ESVHEEORUYRS2E5VHEROYUR5E0SVEHROYUR1E0SV0EHROYUBSREESFAOSROENSSTEORRAVGEICE DATES
5 3 4
Check Engine Oil Level
Change Engine ...
User Manual - Page 18
...battery bolts tight. • Keep small vent holes open or remove caps or covers.
ing wheel. The belts are not. • Slide blade on the mower. • To check blade balance, you do not...grade according to your tractor is maintenance free. If either end of electrolyte is not necessary. Replace belts if they begin to open . • Recharge at 6-10 amperes for normal use.
but are...
User Manual - Page 19
...; With engine cool, remove filter and plug fuel line sec- Clean with oil through oil fill dipstick tube. We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and transmission are covered to remove dirt and stubborn dried gum fibers.
•...
User Manual - Page 20
...procedure described in "INSTALL MOWER AND DRIVE BELT" in the Assembly section of this manual). Have a tight grip on rod and release slowly.
• Remove mower belt from under the tractor. Make ...If tires are properly inflated (See "PRODUCT SPECIFICATIONS" section of mower.
CAUTION: Belt tension rod is parked on both sides of mower to tractor after sliding mower under right ...
User Manual - Page 21
...-to-side adjustment.
02548
BLADE
"B"
"B"
FIG. 22
BOTH FRONT PLATE LINKS MUST BE EQUAL IN LENGTH
02516
NUT "D"
02517
FRONT PLATE ASSEMBLY
NUT "C" TRUNNION
FIG. 23
21
Measure distance "B" at front...loosen nut "D" from trunnion on
both front links. The two front links must remain equal in length. • When distance "B" is pointing straight forward. NOTE: Each full turn of nut "C" ...
User Manual - Page 22
... is spring loaded. Securely
tighten all idler pulleys. SERVICE AND ADJUSTMENTS
TO REPLACE MOWER DRIVE BELT (See Fig. 24)
MOWER DRIVE BELT REMOVAL • Park tractor on locking bracket. CAUTION: Belt tension rod is spring loaded. and L.H. MOWER DRIVE BELT INSTALLATION • Install belt around both mandrel pulleys and around mandrels and entire upper deck surface.
• Remove...
User Manual - Page 23
....
• Place long lower section of belt through loop in midspan belt keeper.
• Check to be sure belt is on proper side of all belt keepers.
• Reinstall mower drive belt onto electric clutch pulley... replaced. Replace brake pads or contact a qualified service center. TO REPLACE MOTION DRIVE BELT (See Fig. 27)
Park the tractor on a level, dry concrete or paved surface...
User Manual - Page 24
.... 28) • Block up axle securely. • Remove axle cover, retaining ring and washers to good chassis ground, away from batteries.
SERVICE AND ADJUSTMENTS
TRACTOR V-BELT DRIVE SCHEMATIC VIEWED FROM L.H. Replace and tighten hub
bolts securely. Keep sparks, flame and smoking materials away from fuel tank and battery.
24 DO NOT...
User Manual - Page 26
...not use engine or carburetor cleaner products in minimizing the formation of fuel gum deposits during
long periods of storage, battery cables should be disconnected and battery cleaned thoroughly (see "TO ...- TRACTOR
Remove mower from one ounce of this manual). • Inspect and replace belts, if necessary (See belt re-
ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.
...
User Manual - Page 28
...3. Travel speed too fast. 3. Low/uneven tire air pressure. 6. Blades improperly installed. 10. Allow grass to open vent holes. Tighten blade bolt. 7. Replace mower drive belt. 9. Headlight(s) not working (if so equipped)
1. Bad battery cell(s). 2. Faulty alternator.
1. CORRECTION
1. Turn ignition key to slower speed. 3. If not corrected, contact an authorized service...
User Manual - Page 29
... not allow the limitation of consequential damages or limitations of how long an implied Warranty may last, so the above limitations or exclusions...Road Augusta, GA 30907 USA
Electrolux Canada Corp. 7075 Ordan Drive Mississauga, Ontario
L5T 1K6
giving the model number, serial number ...belts, blades, blade adapters, normal wear, normal adjustments, standard hardware and normal maintenance.
...
Similar Questions
What Is The Length Of The Belt For The Deck?
what is the length of the belt for the deck?
what is the length of the belt for the deck?
(Posted by nicoparra42 9 years ago)
