Pioneer GM-X332 Support Question
Pioneer GM-X332 Support Question
Find answers below for this question about Pioneer GM-X332.Need a Pioneer GM-X332 manual? We have 1 online manual for this item!
Question posted by Anonymous-173416 on January 12th, 2023
Wattage
How many watts does this amp push?
Current Answers
Answer #1: Posted by Gunarathna on January 13th, 2023 1:05 AM
Gunarathna
Member since:
January 7th, 2023 Points: 1,290
Member since:
January 7th, 2023 Points: 1,290
The Pioneer GM-X542 2 channel amplifier is rated to produce up to 4x80 watts RMS at 4 ohms, 2x160 watts RMS at 2 ohms, and 2x320 watts Max at 1 ohm. It is important to keep in mind that these are the manufacturer's specifications and actual power output may vary depending on the specific conditions in which the amplifier is being used. It is also important to ensure that the amplifier is used within its power handling capabilities to prevent damage and ensure safe operation.
Answer #2: Posted by Gunarathna on January 13th, 2023 1:02 AM
Gunarathna
Member since:
January 7th, 2023 Points: 1,290
Member since:
January 7th, 2023 Points: 1,290
It is not recommended to run the Pioneer GM-X942 2 channel amplifier at a 1 ohm load, as it is not designed to operate safely at such a low impedance. Additionally, even if the amp was able to handle a 1 ohm load, the wattage output would likely be significantly reduced. It is always important to consult the manufacturer's specifications and guidelines to ensure safe and proper operation of any audio equipment.
Answer #3: Posted by SonuKumar on January 13th, 2023 7:36 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
Continuous Power (20Hz-20kHz, 0.08% THD)
2 ch: (4 Ohm) 35Wx2
2 ch: (2 Ohm) 50Wx2
1 ch: (4 Ohm) 80Wx1
Maximum Power (EIAJ)
2 ch: (4 Ohm) 70Wx2
1 ch: (4 Ohm) 160Wx1
Frequency Response: 10Hz - 50kHz (0,-1dB)
Total Harmonic Distortion: 0.004% (1kHz, 4ohm )
Signal-to-Noise Ratio: 103dB (IHF-A Weighted, at 1kHz)
Dimensions: 8-1/8" x 2" x 6-7/8"
https://www.pioneerelectronics.com/PUSA/Car/Amplifiers/GM-X332
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Pioneer GM-X332 Manual Pages
Owners Manual - Page 1
...
In case the necessary information is wrongly performed. CUSTOMER SERVICE DEPARTMENT P.O. Del Valle, Mexico D.F.
follow the instructions carefully. I
BRIDGEABLE POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE PONTABLE
Owner's Manual 6
GM-X332 GM 232
Mode d'emp oi
"con
t- Haven 1087 Keetberglaan 1, 9120 Melsele, Belgium TEL: (0) 3/570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. Imprime...
Owners Manual - Page 2
... RCA equipped car
stereo (standard output of the power amplifier clockwise. When using with an RCA equipped Pioneer car stereo with this power amplifier is turned up , turn the gain control counter-clockwise. • When using the speaker input terminals, turn gain control on .
4 .0
r
LPF (Low-Pass Filter)/HPF (High-Pass Filter) Select Switch (GM-X332)
Set the...
Owners Manual - Page 3
... battery to work when it may become damaged, resulting in the future. The current capacity of the amplifier is included for a lifetime. Turn the car stereo off . After all, we want you can be connected to the amplifier should .
• Never feed power to the power terminal through loud and clear without annoying blaring...
Owners Manual - Page 4
...
-
RCA input jack
System remote control wire (sold separately) Connect the male terminal of the car stereo (SYSTEM REMOTE CONTROL).
Connecting the Power Terminal
• Always use the special red battery and ... body.
2. After making all other connections to the amplifier, connect the battery wire terminal of the amplifier to the auto-antenna relay control terminal. Pass the battery...
Owners Manual - Page 5
...-channel mode (mono)
(Right) Speaker input (Left)
Speaker (Mono)
Three-channel mode (stereo + mono)
The power amplifier is very important to the speaker wires, secure or solder them so they cannot be pulled...Unit
Connecting the Speaker wires
The speaker output mode can be two-channel (stereo), one -channel bridgeable amplifier, but three channels can be used on the following pages. • ...
Owners Manual - Page 6
... point marked, and install the amplifier, either on the chassis
1.
Insert the supplied tapping screws (4 x 18 mm) into the screw holes. Tapping-screws (4 x 18 mm)
Floor mat or chassis Drill a 2.5 mm diameter hole
Specifications
Power source Grounding system Current consumption Average current drawn*
Fuse Dimensions
Weight (GM-X332) Weight (GM-232) Maximum power output...
Owners Manual - Page 7
...THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. TO OBTAIN SERVICE CAR STEREO PRODUCTS (EXCEPT CAR SPEAKERS SOLD IN THE U.S.A. To receive warranty service you cannot exchange the...Company. For additional information on this purpose. Serial No. PRODUCT
WARRANTY PERIOD
PARTS
LABOR
Car Stereo Products
ONE YEAR ONE YEAR
This warranty covers the product during the rental period or...
Similar Questions
Amp Impedence
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
(Posted by truckss415 2 years ago)
Help No Sound
ok amp turns on blue light but no sound when radio is on
ok amp turns on blue light but no sound when radio is on
(Posted by wishfuldreamz32 3 years ago)
Pioneer Gm- X924
how many watt is the pionner gm-x924? i want to buy two speacers for him
how many watt is the pionner gm-x924? i want to buy two speacers for him
(Posted by johnnymd98 10 years ago)
Watts
What is the max wattage for this amp is it 500, Or 1000, please let me know
What is the max wattage for this amp is it 500, Or 1000, please let me know
(Posted by Patrickeden316 12 years ago)