Pfaff hobbylock 794 Support Question
Pfaff hobbylock 794 Support Question
Find answers below for this question about Pfaff hobbylock 794.Need a Pfaff hobbylock 794 manual? We have 1 online manual for this item!
Question posted by lablanchetour on March 21st, 2021
Je Cherche Une Pédale Avec Cordon D'alimentation
J'aimerais acheter une pédale avec cordon d'alimentation pour la surjeteuse hobbylook 794
Current Answers
Answer #1: Posted by Troubleshooter101 on March 22nd, 2021 5:09 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,060
Member since:
September 30th, 2015 Points: 2,927,060
You can buy it from the link below:-
https://www.amazon.com/Control-Pedal-90-223010-23-Sewing-Machines/dp/B07584D43V
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Related Pfaff hobbylock 794 Manual Pages
Owner's Manual - Page 2
.... Notes on safety
A) Due to avoid injury and observe the sewing area continuously while sewing. C) The maximum approved wattage of the needle, the user must be adjusted by anyone but an authorized Pfaff agent.
B) When leaving the machine, changing parts or accessories, the machine must take sufficient care to the up and down movement...
Owner's Manual - Page 3
... sewing machine Accessory box Electrical connection Foot control Preparing for threading Threading, 4-thread double-overedge seam Threading right looper Threading left looper Threading the needles Inserting the lint box Sewing test Points to observe during sewing Securing the seam Checking and adjusting thread tension 3-thread overedge seam Thread chart Adjusting the stitch length on 794...
Owner's Manual - Page 5
Controls of the sewing machine
1 Foot pressure regulating dial 2 Thread guide 3 Carrying handle 4 Left needle thread tension dial 5 Right needle thread tension dial 6...Hand wheel and feed regulator 13 Looper cover 14 Looper cover lever 15 Work support 16 Stitch length setting key on 794
Differential feed setting on 796 17 Needle plate 18 Presser foot 19 Needle bar 20 Thread reel stand 21 Thread reel...
Owner's Manual - Page 6
... the left and pull out the accessory box. Electrical connection Use this machine only on a flat surface or on page 32. Accessory box Swing the work support to a power source. The accessories are illustrated on a special sewing table. Caution: When the machine is not in use, disconnect plug from power source. Do not...
Owner's Manual - Page 7
... run at low Speed. Switching off simultaneously with the master Switch
S Witching on: Press switch. when Pressing harder it will run faster. Machine and sewing light are switched on the foot control
Pos,ho,,
= Half Speed
Posillon 4 = Full speed Foot Control The speed of the HObbyIo is adjusted in two ...
Owner's Manual - Page 9
... support Push looper cover lever to the right, swing cover in the following sequence: 1. Threading procedure Threading must be done correctly to the machine (A). Left looper (orange) 3. Thread the machine in the direction of the arrow and lower it. Left needle (blue) Diagram B shows threading of the thread tension. Opening and closing...
Owner's Manual - Page 12
The diagram shows the correctly threaded machine. insert the thread behind hook A of the thread guide plates fitted on both sides.
Threading the left needle: Thread the left needle in sequence 1 to 7 ...
Owner's Manual - Page 14
... must be sewn. Raise presser foot lever, as shown in illustration. Insert test fabric and lower presser foot.
Make sure that threads have interlocked correctly. Sewing a test sample After threading, a test sample should be guided to the rear, under the presser foot. Hold thread ends with your left hand while turning...
Owner's Manual - Page 15
... the fabric. Use your hand for guiding only. Finishing seam Sew approximately 5 cm beyond the end of the seam and use the thread cutter (1) behind the presser foot to sew. (Also after the machine has been re threaded).
Points to observe during sewing Place the fabric completely under the presser foot when starting to...
Owner's Manual - Page 16
....
Securing the seam:
Knot the thread chain. Note:
When sewing thin fabrics, loosen the upper knife screw after sewing on heavy fabrics. (See illustration). For knit fabrics, a crochet needle can be used to very heavy fabrics. To prevent ravelling of fabric:
This machine will sew through very thin to pull the thread chain into...
Owner's Manual - Page 17
Left looper thread
- See illustration below.
Sew a test sample to be adjusted according to "N" (standard setting). I
- Top side
Right looper thread
Setting thread tensions:
The thread tension should be sure that the ...
Owner's Manual - Page 19
... in needle
clamp guides
0
0
Standard seam width
maxim urn seam width
6.5 mm
4.5 mm 3-thread overedge seam
_____
How to convert from four-thread to threethread sewing: Three-thread sewing is riot used (see page 10).
Owner's Manual - Page 20
... number. A = setting mark. Thin fabrics: Reduce the sewing foot pressure by setting to 2.5 mm
Sewing foot pressure: Position N" of the foot pressure dial is ... Organdy, light-knit fabric, Taffeta, silk, lining materials.
Stitch Ienght setting on 794
The stitch length is the standard sewing foot pressure. The numbers indicate the stitch length in mm which normally is normally ...
Owner's Manual - Page 22
.... It is possible to process (see table on page 21). Owing to 2, also during sewing. U
/cF
WLfl
Adjusting the differential feed
The differential feed prevents interpIy shift. The feed ...amount of either feed dog can be set infinitely from 0.5 to that very good sewing results are possible:
Setting 0.5 = Short stroke of front teed dog, long stroke of rear
feed ...
Owner's Manual - Page 23
... fabrics,
a
popelin
Light cotton. d
nicki fabrics, light knittings
Heavy knitwear,
2
very elastic fabrics
Ill. 1
III 2
0'
g
III. 3
Ill. 4
Gathering can also be set during sewing. In order to make a sewing test has to process
differential feed. Jeans
-
2
c
(normal fabrics)
1.5
3
Jersey, silk, medium cotton.
sure
about
the
setting
r1e differential feed can be made...
Owner's Manual - Page 24
... upper knife to the far right. Note: After adjusting the seam width, it clicks.
Note: Before adjusting the stitch width, always disengage the upper knife. Sew a test sample. To disengage upper knife, open looper cover. Adjusting seam width: Standard setting is "N". Normal stitch width is 3.5 mm. Turn knurled knob (2) clockwise until...
Owner's Manual - Page 25
Changing the sewing feet Push lever A up until the foot snaps on.
23 Place the foot under the presser foot holder so that crosspiece B of the rolled hem foot engages in groove C of the holder (Fig. 2). Push the presser foot lever down and with the other hand gently push lever A up slightly (Fig. 1), and the presser foot will snap out.
Owner's Manual - Page 27
... with Mez Alcazar Or use regular sewing thread,
Mez Alcazar woolly nylon
rayon thread or any other
for this type of the fabric. 9.
the If
fabric is also perfect for a rolled hem with a any other good quality thread.
5. 6.
A for a hem with good quality thread.
5.
The Pfaff Hobbylock 794 is suitable it rolls, the...
Owner's Manual - Page 28
...skipped stitches. Changing knives Knives are blunt. Loosen the needle clamp screw with this machine. Although the correct needle size depends on the fabric and thread used with the ... be replaced when they are available as it clicks. Changing needles Removing needle: Unplug the machine. Raise the needle bar. An incorrectly inserted needle will go and tighten the needle clamp screw...
Owner's Manual - Page 30
... the hand wheel counterclockwise until it into threaded hole (2) of the knife. Changing upper knife: The upper knife is in the lowest position. Unplug the machine.
Tighten slightly and set the upper knife in this position than the surface of the upper knife should be replaced only when the cutting edge...
Similar Questions
Manuel En Francais - Machine Pfaff Tiptonic 1067
Bonjour je recherche le manuel FRANCAIS pour ma machine Pfaff Tiptonic 1067 qui pourra m'aider ?
Bonjour je recherche le manuel FRANCAIS pour ma machine Pfaff Tiptonic 1067 qui pourra m'aider ?
(Posted by marymarie51 10 years ago)