Home » Pfaff » Sewing Machines » Pfaff hobbylock 774

Pfaff hobbylock 774 Support Question

Find answers below for this question about Pfaff hobbylock 774.
Need a Pfaff hobbylock 774 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by rebeccazamora012 on April 22nd, 2013

I Need A Tiny Screw To Hold The Needle In My Pfaff Hobbylock 774 Serger

this tiny screw has a leg to it. i have found screws that have no leg and does not keep the needle secure. any idea where i can find one?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Pfaff hobbylock 774 Manual Pages

Owner's Manual - Page 2

...sewing 9 b. Adjusting the stitch length 15 c. How to adjust 11 g. Threading procedure 6 C. Relation chart for the sewing... 4 a. Adjusting the seam width 15 b. Preparation for fabrics and thread stitch length 10 e. Thread tension adjustment (Normal hemming) 9 c. Replacing the upper knife 17 e. Sewing...Points to obseave during sewing 13 i. 3-thread ...

Owner's Manual - Page 4

No.90 4 Manual 278(W) x 264(D) >< 310(H) 7Kg Brush for dusting Roll hemming presser foot Upper knife Thread stripping discs (4 pcs.) Oiler • Looper mechanism Needle • Controller Dust cover 3 • Accessories Accessories case Screw driver Screw driver (For needle) Tweezers • Specifications Maximum speed Overlock seam width Stitch length Presser foot Presser foot lift ...

Owner's Manual - Page 5

... the foot controller Place the tip of the body. Turning on / off the lamp Sewing light is turned off the machine, sewing light is switched on the pedal. B Preparation for the sewing a. d. b. Fitting the foot controller First, insert the controller connector into the connector socket on a flat and horizontal surface or purpose-built sewing machine table.

Owner's Manual - Page 6

e. When oiling always be sure to the areas indicated. 5 Apply just one or two drops of oil to use a good quality sewing machine oil. Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month.

Owner's Manual - Page 7

...1. To open the side cover, push it to the right until it down towards the machine until it clicks and it to the direc tion of the arrow. Tweezers from the accessories... bag will close side cover, push it will assist you . 3. To close securely. Threading procedure 1. To close the looper cover, push the looper cover upwards lightly towards you to...

Owner's Manual - Page 9

... are satisfied that different coloured threads are used . 3. Lastly thread the left needle surplus thread about 5 cm (about 2") beyond needle eyes. Then proceed to be helpful in the initial stage, (before commencing to sew) that the correct results are to sew with respective needle and looper. Next thread the right neecile 4. It would be used .

Owner's Manual - Page 10

Test sewing After threading, be adjusted accordingly. Hold the 4 threads by your right hand. Checking the threads being ...the machine a. Thread tension adjustment (Normal hemming) The correct thread tension varies depending on the fabric and type and thickness of the upper cutter and start sewing slowly. Dial chart for thread tension adjustment Thread Fabrics Thread L.needle ...

Owner's Manual - Page 11

Correct thread tension Top side 10 Left needle thread Right needle thread Relation chart for fadrica and thread stitch length Normal h.nimlng Roll mg Fabrics Light Organdy, light-knit fabric, Taffeta, silk,lining materials Mdlum Cotton, ...

Owner's Manual - Page 12

f. The sketch shows the right looper thread tension is too loose. 11 The sketch shows the left needle thread tension is too loose. 3. The sketch shows the right needle thread tension is too loose. 2. The sketch shows the left looper thread tension is too loose. 4. Incorrect thread tension and how to adjust 1.

Owner's Manual - Page 13

... and the new foot will then be achieved. 1 . By following this instruction, very good sewing results can then be taken off. 2. Raice the presser foot and then push up the small lever. The foot ...for normal sewing can be engaged. • Correct thread tension of roll hemming Top side Narrow hemming 12 Top side...

Owner's Manual - Page 14

... knife screw again if you have been sewing on heavy fabrics. 13 For knit fabric, a crochet needle can result in needle breakage and cause further damage to needle plate, and looper mechanism. • For finishing a seam, sew approximately 5 cm beyond the seam. Then, flip fabric over and sew over the seam ap proximately 2 cm. • This machine will...

Owner's Manual - Page 15

... is possible by using either right or left hand needles. Use the left hand needle thread and right & left looper thread. 3. Use the right hand needle thread and right & left looper thread. 3. For wide seam sewing. 1. El Iii Ii 14 Wide seam Use left hand needle. 2. Seam width can be changed from 5 mm to 5 mm...

Owner's Manual - Page 17

... needle clamp screw securely. Depending on the weight of fabric you are : 130 / 705H, and the normal recommended size is important to No. 90 may be used. It is No.90. Then using Needle sizes from No. 75 to prop erly insert the screws when refitting needles. cramp Needle clamp screw 16 Light weight materials needing a finer needle, with a thicker needle...

Owner's Manual - Page 18

... it to adjust, loosen the upper knife screw (A) and raise or lower as abnve), and, using a screw driver. Replacing the upper knife DURING THIS OPERATION... tip of needle plate 17 Push into the right, and turn down anti-clockwise towards you ). Only very tiny movements shouki ...normal operation. 3. Then loosen the retaining screw and take off the knife, taking care not to you , lower...

Owner's Manual - Page 19

...release knob turning it anti-clockwise to release the upper knife (as described on page 1 7) Loosen the lower knife screw and remove the lower knife, taking care not to touch the blade. 2. First push into the groove of the ... OUTLET 1. Replace the upper knife in its working position by means of the needle plate and then re-tighten the fixing screw securely. To remove the lower knife. e.

Owner's Manual - Page 20

Replace cover. Insert the new bulb by pushing upward, turning it in direction (1) and remove it. Caution: Use a maximum 1 5 watt bulb only. 19 Replacing the light bulb FIRST DISCONNECT THE MAINS PLUG FROM THE POWER SOURCE • Loosen the screw of the rear of the machine body and remove the lamp cover. • Turn the bulb in the direction (2). f.

Owner's Manual - Page 21

...Incorrectly threaded Thread has caught Thread tension too tight Needle not correctly inserted Incorrect needle used Needle bent or damaged Needle not correctly inserted Incorrect needle used Incorrectly threaded Thread correctly. Insert needle correctly. position 20 E. Sewing problems and solutions Used correctly, your machine should operate efficiently and without difficulty.