Pfaff hobbylock 756 Support Question
Pfaff hobbylock 756 Support Question
Find answers below for this question about Pfaff hobbylock 756.Need a Pfaff hobbylock 756 manual? We have 1 online manual for this item!
Question posted by jesmond99 on June 18th, 2021
High Pitched Screech. Pfaff Hobbylocker 756
The overlocker works well but has developed a high pitched screech scraping sound when it starts up but which disappears when it runs at full speed. I have applied oil and cleaned out lint bit no luck.Janine
Current Answers
Answer #1: Posted by Troubleshooter101 on June 18th, 2021 5:18 AM
Troubleshooter101
Member since:
September 30th, 2015 Points: 2,927,030
Member since:
September 30th, 2015 Points: 2,927,030
Machine is making a high pitched sound while sewing
There are several things to check if the machine is making a noise.
1. Check the bobbin area for any dust, lint or pieces of thread caught in the race.
- Remove the any dust, lint or thread.
- Go to How to clean and install the bobbin area for more information.
3. Upper threading is incorrect.
- Check the steps for threading the machine and re-thread the machine.
- Go to How to thread the machine for more information.
4. Check for scratches on the race.
- Replace the race, or consult your authorized dealer.
Thanks
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Troublshooter101
Answer #2: Posted by SonuKumar on June 18th, 2021 8:35 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,627,790
Member since:
May 9th, 2021 Points: 16,627,790
https://www.pfaff.com/SiteMedia/PFAFF/Products/Machines/Support-manuals/Hobbylock_756-manual-EN.PDF
Machine is making a high pitched sound while sewing
There are several things to check if the machine is making a noise.
1. Check the bobbin area for any dust, lint or pieces of thread caught in the race.
- Remove the any dust, lint or thread.
- Go to How to clean and install the bobbin area for more information.
3. Upper threading is incorrect.
- Check the steps for threading the machine and re-thread the machine.
- Go to How to thread the machine for more information.
4. Check for scratches on the race.
- Replace the race, or consult your authorized dealer.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Pfaff hobbylock 756 Manual Pages
Owner's Manual - Page 2
... high-quality product that provides unique advantages. Your new hobbylock 756 can take a bit of immedia tely. If you in your PFAFF ... coding of service with three pins. So now let's get started! We wish you now take any help or advice. Spare ...PFAFF hobbylock features the very latest in the mains lead of this instruction manual is just as approved by ASTA according to -date sewing...
Owner's Manual - Page 3
... covers, lubricating, or when making any other liquid. Always use this sewing machine is used by pulling on page 2
KEEP THESE INSTRUCTIONS IN A SAFE PLACE.
4 Always unplug sewing machine from the accumulation of lint dust and loose cloth 5.
Do not place or store a sewing machine where it has
been dropped or damaged, or dropped into water or...
Owner's Manual - Page 4
... 100 C to 40° C Humidity 20 % to use the sewing machine if: - and even surface.
5. Do not use only original PFAFF parts. To remove any objects in openings on the specification plate.
6....machine.
7. Please Note! it is free of the sok ket by a Ptaff mechanic. If this appliance is defective, - Never use a dry, clean and soft cloth which the user can re pair. it is a high...
Owner's Manual - Page 5
...
20
a How to balance the 4 thread
overlock mock safety stitch
20
• Suggested tension setting for upper
looper thread wrapped rolled hem .27 . . . • How to reinforce a seam
35
• Braiding by chaining off and test sewing
18
13. Machine maintenance
40
• Cleaning the machine
40
• Oiling the machine
40
• How to replace the...
Owner's Manual - Page 6
... the
flat shank possibility
industrial needle of inserting the
needle backwards.
*
Do not attempt to use sewing machine needle of
a standard any size or
household type in this
overlock.
#2054
Overlock needle
*
ms(te2yaw0pce5ihns4ign-a0nere6.ewe)adoRvlveaeaerginel#ua2lbaal0freva5abi4pinrlioacssbisiinlzzeteesanfn11oe4d0er,dislsb1ee2faswu,llri(1nn#4igps2&ho0eik5ndn14t6i-tw.s4n.i2teh...
Owner's Manual - Page 8
To reduce the risk of electric shock, this sewing machine has to be used also for light switch) to turn "ON" Push "0" mark side
to turn "OFF"
* To run the machine and control the speed, press the controller.
* The harder you . ()
Caution: Be sure looper cover is intended to the
machine receptacle ().
* Plug power line © into...
Owner's Manual - Page 11
...
CYLINDER COVER
* Removing the cylinder cover exposes the lower looper for free arm sewing (tublar work)
* To remove, pull cloth plate to the left .
* To replace...when lifting or
•1
carrying the machine. 9 HOW TO REMOVE AND REPLACE
CLOTH PLATE
* Remove cloth plate for easy threading and cleaning of cloth plate upward.
* To replace, guide latch on the machine, it can be removed easily by...
Owner's Manual - Page 20
... the threads and apply a slight tension. * Turn the hand wheel toward you have rethreaded the machine
always chain off and sew a test sample ...run the machine with the presser foot down until the chain reaches 5 7.5 cm (2 3 inches) in length.
* Clip the thread chain. Note: Anytime you 2 or 3 complete
turns to the left under the front of the threads over the throat plate and slightly to start...
Owner's Manual - Page 21
... a one- BASIC STITCH TYPES
• 4 THREAD OVERLOCK MOCK SAFETY STITCH
* This machine is a four-thread overlock that uses two needles and two loopers to balance the tensions,
it is 1)
recommended that Adjustments be in
no
greater
than
half
a number at a time. 2) Sew a test sample after each adjustment.
.4
S
Current Setting is sewn. The right needle...
Owner's Manual - Page 25
...machine one at a time.
1'
*
If threads do thread guides
not pull easily, check for
should be set on
*
When when
pulling the knot
thread through the needle.
* Return tension dials to previous settings.
16. on the 3mm most sewing... TO DISENGAGE MOVABLE
UPPER KNIFE
9 TNOONPLWAOCREKMINOGVPAOBSLIETIKONNIFE IN
* Be sure the machine is in the up position * Turn the hand wheel toward you ...
Owner's Manual - Page 26
Caution: Always close looper cover before operating machine.
18. • TO PLACE MOVABLE KNIFE IN WORKING POSITION
* Open looper cover and push the movable knife
[
holder to the right as ... left needle is inserted, the thick line on the left of the looper cover is 16.0mm (5/8 inch).
* When sewing with the right needle, the thick line on the left of the looper cover is 14.0mm (35/64 inch). Note...
Owner's Manual - Page 27
...)dcbthoy) adjusting the stationary knife. Left need'e
Left need'e
* Be sure the machine is needle position
set to decrease in the accesso
ries. (1)
*
Move the stationary...position
(page 24).
*
Test sew pensate
and for
adjust tensions as the increase or
necessary to sew the three-thread stitch at a
width of 5.7mm (7/32 inch).
*
The machine is disconnected from the
power source...
Owner's Manual - Page 28
HOW TO SEW A ROLLED HEM
* Rolled hemming is done by rolling and overedging the fabric edge.
* Light ....
* Unscrew the throat plate 3crew.
1F
*
Install careful
the not
rolled hemming throat plate being to catch the threads between the plate
and the machine.
* Replace throat plate screw.
* Open looper cover (page 6).
* Disengage upper knife (page 23). * Remove the cylinder cover (page 9). ...
Owner's Manual - Page 29
... to "2-F" and a fine seam will be sewn.
* This machine can sew two types of rolled hems.
• SUGGESTED TENSION SETTINGS FOR STANDARD ROLLED HEM
* Always sew a test sample and adjust tension balance if neccessary.
* Adjust ... tension dial
-
(orange) to roll.
1 Always sew a test sample, and if neccessary, adjust tension balance as for a narrow three-thread overlock stitch (page 21).
Owner's Manual - Page 31
... adjusting the tension of the three-thread overlock stitch, sewing the seam and pulling the fabric apart to flatten the seam.
* The flatlock stitch can be used as a construction and decorative stitch or for ornamentation only.
(1) MachineSetUp * Remove the left or right needle. * Begin with the machine threaded and tension
balanced for the...
Owner's Manual - Page 33
... fabric before cutting out the garment
* Remove the left needle and adjust machine for a narrow three-thread overlock stitch. The overlock blind hem is almost invisible.
* Remove the left needle and adjust machine for a narrow three-thread overlock stitch. • HOW TO SEW AN OVER LOCK BLIND HEM
The excess fabric is trimmed and the hem...
Owner's Manual - Page 34
... the presser foot so that the knife is positioned in line with the cut edge. * Pull slack threads up, then start to release the thread caught on the finger of the machine just
enough to sew.
(2) Inside Corner * Cut fabric at seam edge.
32 * Fold the fabric with the wrong sides together and...
Owner's Manual - Page 42
...of the knives. 2) An overlock runs at a very high speed and needs to lubricate the internal working parts.
. CLEANING THE MACHINE
Danger: Before cleaning your machine, disconnect power line plug from the wall receptacle.
* Clean the lint from the looper and knife area often with a dry lint brush.
• OILING THE MACHINE
Danger: Before lubricating your machine, disconnect power line plug from...
Owner's Manual - Page 45
... sewing Check for light weight
fabrics
Check alignment of needle
- Increase presser foot pressure for heavy weight fabric Decrease presser foot pressure for tangled or caught thread - Increase presser foot pressure Use a high quality thread
- Insert needle correctly
-
Compress thick layers of fabric with overlock
Connect machine to power source
- Page
23 38
38...
Owner's Manual - Page 47
... gather stitching).
28. (5) Ultra Hem Foot
F-
* Special foot that makes sewing a blind hem easier. The machine will trim the excess fabric, finish off the edge and sew a hem in one operation.
(See page 31)
(6) Clean Pocket
* Fits under the base of threads Machine dimensions Weight hobbylock 756
Specification
1,300 spm maximum 1-5 mm (Standard: Rolled hemming F -2, ordinary overedge...
Similar Questions
Tips To Thread Needle Number 4 On The Pfaff Hobbylock 756
I am having a lot of trouble threading needle #4 on the Pfaff Hobbylock 756. Are there any tips you ...
I am having a lot of trouble threading needle #4 on the Pfaff Hobbylock 756. Are there any tips you ...
(Posted by CASHmere84 9 months ago)
Edge Guide - Pfaff Select 1540 Sewing Machine
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
How does the Edge Guide work for the Pfaff Select 1540 sewing machine?
(Posted by jesjames 2 years ago)
I To Replace My Roll Hem Foot For My Pfaff Hobbylock 756 Server. Can You Help.
everything is said above
everything is said above
(Posted by Desideles2998 7 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
What Is The Correct Tension On Pfaff Hobbylock 756 Serger
(Posted by sabrinarenfroe 10 years ago)