Pfaff Tipmatic 1027 Support Question
Pfaff Tipmatic 1027 Support Question
Find answers below for this question about Pfaff Tipmatic 1027.Need a Pfaff Tipmatic 1027 manual? We have 1 online manual for this item!
Question posted by myrnamjs on May 10th, 2021
Stitch Selection - Zigzag Etc.
good day, please tell me how the stitch selection works on the tipmatic 1027 sewing machine
Current Answers
Answer #1: Posted by Odin on May 10th, 2021 6:04 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
This topic is covered in the two pages starting with https://www.manualslib.com/manual/504977/Pfaff-1025.html?page=18#manual.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/pfaff/customer-service.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/pfaff/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Pfaff Tipmatic 1027 Manual Pages
Owner's Manual - Page 2
...tensions Regulating the stitch length Reverse sewing Finger-tip controls 1027 Finger-tip controls 1025 Selecting utility stitches Selecting stretch stitches Utility- and stretch-stitch combinations 1027 Selecting the needle position for straight stitching
Droppingthemachinefeed Changing the needle
Changingthesewingfoot Special sewing feet Buttonhole settings Sewing buttonholes
Sewing feet Changing...
Owner's Manual - Page 4
... bulb in the sewing lamp.
c) Be sure to interrupt sewing and leave the machine for entering phone number of your sewing machine
Some safety rules
I 30 Carrying handle 31 Hinged top cover 32 Hand wheel 33 Stop motion knob 34 Master switch 35 Finger-tip controls 36 Stitch length control 37 Swing-out sewing arm with accessory...
Owner's Manual - Page 5
Opening the hinged top cover Also fold the handle toward the left (C) and lift it out toward the rear. On Model 1027 a stitch chart is found on the inside of this cover (A).
Removing and opening the swing-out arm Reach under the swing-out arm with your left ...
Owner's Manual - Page 6
C shows how the second spool holder
snap-on sewing feet, the and the seam ripper fit
into the box. C
a
0
0 I;- C
2
.
Accessory box and accessory compartment sTliofiltrtyitucpooutmht ep(Aaf)rr.tomTnhet enortfe(aBics)caeunsnsdaoedrrdynietbiaootnxha.4l 6acacneds
Ill.
Owner's Manual - Page 7
... out of the machine. Push plug B into the machine socket and plug C into the wall outlet.
Foot control
Place the foot control under the table. The more the pedal is placed in the machine again as shown in the illustration (A).
Press down the pedal, and the machine starts sewing. Your machine is now readyfor sewing. Press master...
Owner's Manual - Page 8
...the spool and draw it into the left.
4 Upper threading Raise the sewing foot. One of the threads is used for bobbin winding and twinneedle sewing. Placing spool of thread on it. C Second spool holder:
This is... contained in front of the spool of thread.
For two-needle sewing, draw one thread into slot Ato the left of thread, as shown in front of the ...
Owner's Manual - Page 9
V
Disengaging the sewing mechanism Before you .
Hold the hand wheel steady and turn the stop motion knob toward you start winding the bobbin, disen gage the sewing mechanism. After bobbin winding, tighten the knob again by turning it away from front to back.
Threading the needle Thread the needle from you.
5
Owner's Manual - Page 10
... tension stud 55, wind it around bobbin tension stud 55. Disengage the sewing mechanism. Draw the needle thread under the sewing foot, up and into slot 54, and from above around the bobbin ...point. Winding the bobbin through the needle eye (B)
Raise the sewing foot and bring the needle to start the winder.
Re-engage the sewing mechanism.
6 Insert the spool holder and place a spool of...
Owner's Manual - Page 12
Turn hand wheel 32 toward the left and back under the sewing foot.
8 Pull the bobbin thread out of the needle hole and lay both threads toward you until the needle
movesdownand upagainandthetake-up lever is up . ...
Owner's Manual - Page 13
... raised further for sewing. C The sewing foot is lowered for inserting extra-thick materials.
Thread cutter The thread cutter is an oblique slot located at the back of the machine toward you to cut them.
9 Presser bar lifter Lever 42 has three positions: A = The sewing foot is raised. (Before you
remove the work out of...
Owner's Manual - Page 15
... keep this button depressed, the machine sews back wards.
11 Reverse sewing
Push button 44. Regulating the stitch length Turn the control so that the number indi cating the stitch length chosen is opposite mark A. Stitch length range: Model 1025: 0-4 Model 1027: 0-6 Ill. B shows how to set the stitch length control for sewing stretch stitches (red stitch symbols on push buttons).
Owner's Manual - Page 16
... 1027 10 Elastic triple straight stitch
Straight stitch 11 Pullover stitch
Blindstitch 1 2 Closed overlock stitch
Joining stitch 1 3 Overlock stitch
Shell-edge stitch 14 Feather stitch
Elastic decorative stitch 1 5 Honeycomb stitch
Elastic stitch
1 6 Elastic triple zigzag stitch, 5 mm 5-mm zigzag stitch
17 Elastic triple zigzag stitch, 3.5 mm 3.5-mm zigzag stitch
1 8 Elastic triple zigzag stitch...
Owner's Manual - Page 17
... of model 1025 10 Elastic triple straight stitch
Straight stitch
1 3 Overlock stitch Shell-edge stitch
14 Feather stitch
Elastic decorative stitch 1 5 Honeycomb stitch
Elastic stitch
I
13 I 1 6 Elastic triple zigzag stitch, 5 mm 5-mm zigzag stitch 1 7 Elastic triple zigzag stitch, 3.5 mm 3.5-mm zigzag stitch
1 8 Elastic triple zigzag stitch, 2 mm 2-mm zigzag stitch
19, 20, 21: Buttons for...
Owner's Manual - Page 18
Selecting stretch stitches
(red symbols) Push the desired button and turn the stitch length control to the number indicating the desired stitch length (1 -6 on model 1027, or 1-4 on model 1025). Selecting utility stitches (white symbols) Push the desired button and turn the stitch length control as far as it will go (red symbol).
Owner's Manual - Page 19
For example, if you want to sew an elastic blindstitch, push buttons 1 5 and 1 6, select a stitch length between 1 and 4. This stitch can also be sewn with model 1025.
Utility- Selecting the needle position for straight stitching
Left needle position: push button 20 Central needle position: push button 1 0 Right needle position (model 1 027): push buttons 11 and 1 2.
L ri J
6
L and...
Owner's Manual - Page 20
... feed dog is dropped (for zigzag and utility stitch sewing.
16 Changing the needle Raise the needle bar. Twin needles with the flat side of 1.4mm may be used for embroidering, darning, etc.) For sewing, push the drop-feed control toward B. Push the drop-feed control toward A.
Dropping the machine feed
Open free arm cover...
Owner's Manual - Page 22
... E moves along the right or left zipper chain. C Darning foot Remove the sewing foot holder and secure the darning foot in the buttonhole range of the foot, pull it taut and clamp it in front lug D. Regulate the stitch density in position with screw H.
This serves to determine the buttonhole length. The...
Owner's Manual - Page 23
... button 21 . Raise the needle.
4 Push button 20 and keep it depressed until the machine has sewn 4 to 6 bartacking stitches. Raise the needle. Then release the button.
5 Sew a few tying stitches. Turn hand
wheel torward you until the machine has sewn 4 to 6 bartacking stitches. Sew the second button
hole seam the same length as it will go...
Owner's Manual - Page 25
...-free. Cleaning and oiling Tilt needle plate 38 up at the back (A) and take it is put a drop of the sewing hook with a sàft brush. Do not oil the machine because it out (B). Push it up and turn it toward B. Insert the new bulb so that its pins slide in the...
Owner's Manual - Page 26
...good-quality thread. Let machine feed the work is pushed or pulled. Thread tension too strong. Needle bent. Remedy:
Push needle up as far as it snaps into place.
22
Needle too thin for thread used . Needle too thin or too thick. Insert system 1 30/705 H needle.
Select... Only guide the material lightly. Machine skips stitches Needle not inserted correctly. Check...
Similar Questions
Stitch Length Won't Change, Reverse Won't Engage.
I can't change stitch length (on any stitch type) or backstitch (reverse). Any suggestions?Power com...
I can't change stitch length (on any stitch type) or backstitch (reverse). Any suggestions?Power com...
(Posted by bostonwolfepack 4 years ago)
Tipmatic 1027 Has Power, The Light Is On , But It Won't Run.
Plugged in. Light on. no movement when foot pedal depressed. fly wheel turns. needle rises and falls
Plugged in. Light on. no movement when foot pedal depressed. fly wheel turns. needle rises and falls
(Posted by joannekulesza 8 years ago)
Pfaff Tipmatic 1027 -emitting Smoke
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
(Posted by Clingwood 9 years ago)
Chain Stitch Not Working On 5 Thread Overlock.
Chain stitch not working on 5 thread safety stitch. What am I doing wrong.
Chain stitch not working on 5 thread safety stitch. What am I doing wrong.
(Posted by Renettekumm 9 years ago)
Pfaff Tipmatic 1027 Bobbin Winder
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
(Posted by gdhulbert 9 years ago)