Pfaff Tipmatic 1027 Support Question
Pfaff Tipmatic 1027 Support Question
Find answers below for this question about Pfaff Tipmatic 1027.Need a Pfaff Tipmatic 1027 manual? We have 1 online manual for this item!
Question posted by monaleecq on July 31st, 2020
How Do I Solve Loose Under Thread?
Hi I bought a Pfaff 1027 Tipmatic second. It sewed beautifully. I sewed quilted plate 'coasters'. When I finished basting stitches (Width 4), I turned to the back to a line of loose threads!No matter how many times I re-thread, I get the same result.
Current Answers
Answer #1: Posted by waelsaidani1 on July 31st, 2020 4:56 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,777
Member since:
May 12th, 2013 Points: 19,501,777
This issue is caused by your bobbin tension so make sure you have the correct bobbin. Try reinserting the bobbin into the bobbin case and then put your finger on the bobbin so it cannot move then when you pull the thread into the tension on the bobbin case the thread will be pulled firmly into the tension on the bobbin case. This should resolve that issue.
Answer #2: Posted by INIMITABLE on July 31st, 2020 5:00 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,087,520
Member since:
April 3rd, 2020 Points: 2,087,520
Your tension needs to be adjusted. Here is a video guide
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Pfaff Tipmatic 1027 Manual Pages
Owner's Manual - Page 2
...connection Foot control Placing spool of thread on pin Upper threading Threading the needle Disengaging the sewing mechanism Bobbin winding Removing bobbin case and bobbin Inserting the bobbin Inserting the bobbin case Drawing up the bobbin thread Presser bar lifter Thread cutter Thread tensions Regulating the stitch length Reverse sewing Finger-tip controls 1027 Finger-tip controls 1025 Selecting...
Owner's Manual - Page 4
... your sewing machine
Some safety rules
I 30 Carrying handle 31 Hinged top cover 32 Hand wheel 33 Stop motion knob 34 Master switch 35 Finger-tip controls 36 Stitch length control 37 Swing-out sewing arm with accessory compartment 38 Needle plate 39 Sewing foot holder with sewing foot 40 Needle holder with screw 41 Needle thread tension...
Owner's Manual - Page 5
... toward the rear. Then lift the cover off the carrying case cover, fold the handle to accom modate thread and accessories.
4
4
N
1
Open its lid (E) to the rear, as indicated byan arrow. On Model 1027 a stitch chart is found on the inside of this cover (A).
Opening the hinged top cover Also fold the handle...
Owner's Manual - Page 6
Accessory box and accessory compartment sTliofiltrtyitucpooutmht ep(Aaf)rr.tomTnhet enortfe(aBics)caeunsnsdaoedrrdynietbiaootnxha.4l 6acacneds
Ill. C
2
. I;-
C
a
0
0 C shows how the second spool holder
snap-on sewing feet, the and the seam ripper fit
into the box.
Owner's Manual - Page 7
... (A). Electrical connection Take the foot control out of the machine. When you put the machine away, the foot control is depressed, the faster the machine runs.
3 Press master switch 34.
Press down the pedal, and the machine starts sewing. Your machine is now readyfor sewing. Push plug B into the machine socket and plug C into the wall outlet.
Foot...
Owner's Manual - Page 8
... slot Band take-up lever 52. Placing spool of thread on it. B Large spools of thread:
Push unreeling discs D and Eon the spool holder in front of the spool of thread, as shown in front of the spool of thread. Upper threading Raise the sewing foot. Insert the spool holder in the accessory box and is...
Owner's Manual - Page 9
Threading the needle Thread the needle from you.
5
After bobbin winding, tighten the knob again by turning it away from front to back. Hold the hand wheel steady and turn the stop motion knob toward you start winding the bobbin, disen gage the sewing mechanism. V
Disengaging the sewing mechanism Before you .
Owner's Manual - Page 10
... take it around the bobbin a few turns of thread on spindle 47 so that pin Centers slot D. Pull the thread from the spool, lead it around bobbin tension stud 55. Leave the top cover open during bobbin winding. Winding the bobbin through the needle eye (B)
Raise the sewing foot and bring the needle to...
Owner's Manual - Page 11
... out the bobbin case, release the latch and take out the bobbin. Removing bobbin case and bobbin Open free arm cover 48. Then draw the thread into slot B and
under the spring into the bobbin case so that the...
Owner's Manual - Page 12
Turn hand wheel 32 toward the left and back under the sewing foot.
8 Inserting the bobbin case Pull out latch K and push the bobbin case onto stud B, ...making sure slot A is up. Release the latch and lightly press against the bobbin case to make sure it has snapped into
place. Pull the bobbin thread...
Owner's Manual - Page 13
Raise the sewing foot.
Pull the work , turn the hand wheel toward the back. Thread cutter The thread cutter is an oblique slot located at the back of the machine toward you to cut them.
9 Presser bar lifter Lever 42 has three positions: A = The sewing foot is raised. (Before you
remove the work out of the presser...
Owner's Manual - Page 14
...B = Regulating screw.
Turn it leftfora loosertension, or right for a tighter tension. The correct lower tension Let the bobbin case with a full bobbin hang down by the thread. E
I
10
It ...tensions are correct D = Upper tension too loose or lower tension too tight. The higher the number, the tighter the tension. E Lower tension too loose or upper tension too tight.
The normal ...
Owner's Manual - Page 15
Reverse sewing
Push button 44.
Regulating the stitch length Turn the control so that the number indi cating the stitch length chosen is opposite mark A. B shows how to set the stitch length control for sewing stretch stitches (red stitch symbols on push buttons). Stitch length range: Model 1025: 0-4 Model 1027: 0-6 Ill. As long as you keep this button depressed, the machine sews back...
Owner's Manual - Page 16
... 1027 10 Elastic triple straight stitch
Straight stitch 11 Pullover stitch
Blindstitch 1 2 Closed overlock stitch
Joining stitch 1 3 Overlock stitch
Shell-edge stitch 14 Feather stitch
Elastic decorative stitch 1 5 Honeycomb stitch
Elastic stitch
1 6 Elastic triple zigzag stitch, 5 mm 5-mm zigzag stitch
17 Elastic triple zigzag stitch, 3.5 mm 3.5-mm zigzag stitch
1 8 Elastic triple zigzag stitch...
Owner's Manual - Page 19
... position: push button 1 0 Right needle position (model 1 027): push buttons 11 and 1 2.
For example, if you want to sew an elastic blindstitch, push buttons 1 5 and 1 6, select a stitch length between 1 and 4. and stretch-stitch combinations, model 1027
The various stitch combinations are shown in the chart on the inside of the hinged top cover. L ri J
6
L This...
Owner's Manual - Page 20
... with the flat side of 1.4mm may be used for embroidering, darning, etc.) For sewing, push the drop-feed control toward A.
Changing the needle Raise the needle bar. Insert ...The feed dog is dropped (for zigzag and utility stitch sewing.
16 Then hold the needle, loosen screw A and pull the needle out downwards. Dropping the machine feed
Open free arm cover 48. Then tighten screw A.
Owner's Manual - Page 23
... lever is up. Turn the hand wheel toward you to raise the needle. 2 Push button 20 and keep it will go. 1 Sew first buttonhole seam. Then
release the button. 3 Push button 21 . Sew the second button
hole seam the same length as it depressed until the machine has sewn 4 to 6 bartacking stitches. Raise the needle...
Owner's Manual - Page 25
... C. Changing the light bulb
Push the light bulb up, turn it toward A and pull it out. Cleaning and oiling Tilt needle plate 38 up at the back (A) and take it is put a drop of the sewing hook with a sàft brush. Do not oil the machine because it out (B).
All you have to do...
Owner's Manual - Page 26
... For any of the above . Regulate thread tensions.
Let machine feed the work is pushed or pulled. Machine skips stitches Needle not inserted correctly. Needle too thin for thread used , or thread that has become too dry by excessive storage.
3. Thread tension too strong. Insert system 1 30/705 H needle.
Insert new needle and push it up as...
Owner's Manual - Page 27
... feed dog. Check upper and lower tensions. Use first-class thread only.
Machine runs with difficulty Thread ends in hand, but pass it through the bobbin tension stud.
During bobbin winding, do not hold thread in hook raceway. Remove needle plate and clean out lint. Machine feeds irregularly or not at left.)
Flick reverse-feed control...
Similar Questions
Issue With Settings On Pfaff Creative 3.0.
I just inherited this machine. Upon set up, I turned it on, threaded the machine, sewed a bit and th...
I just inherited this machine. Upon set up, I turned it on, threaded the machine, sewed a bit and th...
(Posted by jnuhn 2 years ago)
My Machine Is Not Feeding All Layers
my machine will not feed /sew properly all three layers of quilt ,it works well on sample made up of...
my machine will not feed /sew properly all three layers of quilt ,it works well on sample made up of...
(Posted by margaretandross 8 years ago)
Tipmatic 1027 Has Power, The Light Is On , But It Won't Run.
Plugged in. Light on. no movement when foot pedal depressed. fly wheel turns. needle rises and falls
Plugged in. Light on. no movement when foot pedal depressed. fly wheel turns. needle rises and falls
(Posted by joannekulesza 8 years ago)
Pfaff Tipmatic 1027 -emitting Smoke
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
My Pfaff 1027, while not being used, started to emitt smoke from various openings. I unplugged and l...
(Posted by Clingwood 9 years ago)
Pfaff Tipmatic 1027 Bobbin Winder
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
I cannot get the bobbin winder on Pfaff Tipmatic 1027 to run and wind the thread on. I have had to w...
(Posted by gdhulbert 9 years ago)