Panasonic WJSX150A Support Question
Panasonic WJSX150A Support Question
Find answers below for this question about Panasonic WJSX150A - SWITCHER/MULTIPLEXER.Need a Panasonic WJSX150A manual? We have 1 online manual for this item!
Question posted by ptchevy on December 12th, 2012
Crossconnect Cable Pinout For Master To Slave Configuration.
I'm trying to connect two WJSX150's together in a Master, Slave configuration, but I keep getting "Slave Down" and I cant see the cameras connected to the slave unit. I believe that it's the cable connecting port 3 on the master to port 4 on the slave unit. Does anyone have a pinout for this cross connect cable?
Current Answers
Related Panasonic WJSX150A Manual Pages
WJSX150A User Guide - Page 10
... to control the equipment connected to this unit sends the control data and VD2 timing pulse to 4. The unit is equipped with the circuit to display each channel. When using the DATA 4 port, you can be configured and uploaded to the unit.
* Example: Camera selection, monitor selection, and dwell time (the time to multiplex or separate the...
WJSX150A User Guide - Page 14
...camera switching pulse is supplied from a tour sequence into the spot mode is a number. The change from Rn)
15
SLAVE DOWN (Displayed when communication is not established between the Master and Slave units... Mode
Camera images are displayed for example, power/cable disconnection) * "n" is a number. Before use, the parameters of 64 steps and up to 32 sequences are configurable.
Time...
WJSX150A User Guide - Page 24
... select either a composite color or B/W video signal from a camera. Daisy chain connection is also available. • When the unit is used as a standard accessory) into this socket and connect it to an AC outlet.
!9 Blank panel When the Multiplexer board installed in the master-slave
connection, terminal-mode system controllers can connect to the monitors at these connectors. When the...
WJSX150A User Guide - Page 35
... the camera's unit address as shown in the chain, as RG-59/U, BELDEN 9259 or equivalent.
One is required, use cameras and matrix switcher with RS-485 communication feature. Notes: • Before connecting RS-485 cameras to DATA1 to 3, data port setting through WJ-SX150A Administrator Console is always set improperly. • Do not use coaxial cable...
WJSX150A User Guide - Page 38
... terminals until the reset. Connect the unit's DATA HDR connector to the recorder's DATA port with a modular cable. (The control data and alarm signal will be output from the unit to the recorder.)
Monitor
Matrix Switcher
EXT IN
MONITOR OUT
ALARM
DATA HDR DATA 4 TERM OFF ON
SERIAL DATA 3 DATA 2 DATA 1
RS485(CAMERA) LINE
2 SELECT 4
EXT...
WJSX150A User Guide - Page 41
... the description of the recorder to 1. (Refer to the Master unit. Connect the unit's CAM OUT 1 to 8 connectors to the recorder's VIDEO IN 1 to 8 connectors with the system controller connected to the recorder's operating instructions.) 2. Connect the unit's DATA HDR connector to the recorder's DATA port with a modular cable.
(The control data and alarm signal will be output...
WJSX150A User Guide - Page 42
... different, the recorder will not be operable. • In these connections, you cannot use a PS·Data system controller. • If you cannot control the recorders with a coaxial cable. 4. Set the recorder's unit address to a number 5 or larger . (Refer to the Master unit. Connect the unit's EXT IN connector to the recorder's MULTI SCREEN OUT connector with...
WJSX150A User Guide - Page 45
To record the camera images through a time-lapse VCR, install an optional Multiplexer board in SETUP MENU. (Refer to automatically recover from alarm reset. Connect the matrix switcher's EXT OUT (REC OUT) to the time-lapse VCR's video output connector with the coaxial cable. Connect the matrix switcher's EXT IN (PLAY IN) to the time-lapse VCR's video...
WJSX150A User Guide - Page 50
... 4: Master, Slave 1 to 4 are connected in p. 24.) *n is a version difference, update the firmware of each unit to the newest using a CD-ROM. (Refer to pp.58 to 60 FIRMWARE UPDATE.)
● Preparation
Prepare the following items besides standard accessories. • Personal computer x 1 (Refer to p. 79 Platform for details on system requirements.) • 9-pin D-sub crossing cable...
WJSX150A User Guide - Page 51
...9679; Video Cable Connection
Connect the camera input connectors of Master and the monitor output connectors of Slave with Cable Kit WV-CA48/10K. • Set the termination selectors of the Master and terminal Slave unit to ON. • Set the termination selectors of other Slave units to OFF. • Connect system controllers to the Master unit. (Refer to p. 39.)
Example: Master, Slave 1 and...
WJSX150A User Guide - Page 52
... directly-connected cameras when the Master and Slave 1/2/3 are not for recording but for connection procedures. Example: Master, Slave 1 and 2 are connected in the system. • The Master unit's camera channels which loop thru Slave units cannot be connected to the recorder. (In the illustration, the Master unit's CAM OUT 1 to 8 and the recorder's VIDEO IN 1 to 8 cannot be configured in...
WJSX150A User Guide - Page 53
... more than one video input (WJ-HD500 or WJ-HD200 Series), conform the LCN (logical camera number) settings of the unit to the camera number setting of each unit to the Master unit. 7. ton on the "OK" button.
Set the connected Slave units to the Master unit, do the setup procedure with SETUP MENU or WJ-SX150A Administrator Console.
• With...
WJSX150A User Guide - Page 58
...WJSX150A Administrator Console can configure timer event, camera cleaning, and daylight saving time.
• Timer event: A sequence or spot mode can configure the communication speed (baud rate) of every month, week or day. WJ-SX150A Administrator Console (PC)
SETUP PROCEDURES
■ Setup Procedures
This unit has two setting procedures. Master-slave connection settings • Master-slave...
WJSX150A User Guide - Page 59
... ports DATA 1 to 3 connect to the system controller's operating instructions.
● System Settings
SETUP MENU can also activate/deactivate dynamic recording, dummy black, and "CAMSW LOSS Rn" indication. (Rn is a recorder number.) MUX
• Mux camera (Multiplexer) title: Camera titles which are displayed with the data port configurations through WJSX150A Administrator Console.
● WJ...
WJSX150A User Guide - Page 66
... the cursor and press the CAM (SET) button to configure the parameters.
* In normal connection, only MASTER is N.
OFF: An alarm input is selected. SWITCHER: Select a unit (SLAVE1 to 4 and MASTER*) to go into the menu. Logical camera number and sensitivity
C01 LOW
+
Mark
The following is connected to ON or REC ONLY, and press the CAM (SET...
WJSX150A User Guide - Page 70
... CAMERA NUMBER
This menu links to the former position. SWITCHER: Select a unit (SLAVE1 to 4 and MASTER*) to 99 is selected.)
Is the MASTER-SLAVE changed .
SETUP MENU will be closed, but the setting will be changed ? After the configuration, press the MON (ESC) button. The factory default settings are shown in the diagrams.
When only Master is connected CAM...
WJSX150A User Guide - Page 71
...
2 of 2
SWITCHER=SLAVE1(1 of the Master unit which connect Slave units are displayed as a space. When you select logical camera numbers, the setting will be changed to a space.
• COMPENSATION/VD2/DATA
This menu links to ▲ at the bottom of the Master unit which connect Slave units are displayed as a space. When Master, Slave 1 to 3 are connected
CAM 1 2 3 4 5 6 7 8 9 10...
WJSX150A User Guide - Page 72
.../K2/ K3/K4 CAMERA
TERMINAL-K1/K2/ K3/K4 CAMERA
TERMINAL-K1/K2/ K3/K4 CAMERA
Slave 1 to this parameter. MASTER-SLAVE: The port used for the master-slave connection is fixed to configure the parameters.
* In normal connection, only MASTER is set to the default speed when CONTROL is same as the illustration. SPEED: This stands for Master-Slave connection
SWITCHER: Select a unit (SLAVE1 to...
WJSX150A User Guide - Page 79
....
(Cancel Exit) button Cancels the configuration and closes the Master-Slave window. Notes: • If logical camera numbers are not selected, the cameras' LCNs are connected in the system, you click on the (Logical Camera Number) button in each unit. If you configure the master-slave composition, settings concerning LCN (logical camera number) and Multiplexer Title (refer to p. 100) will...
WJSX150A User Guide - Page 94
... the baud rate for master-slave connection. The factory default setting is fixed to VCR. Refer to p. 58 for 600 RECORDER in SETUP
MENU (refer to p. 71), the Protocol of SERIAL is 1.
● Parameters (Slave 1 to 4)
■ Recorder
This window configures the recorder setting parameters: whether the multiplexer board is installed in the unit, what is the...
Similar Questions
I Have Former Nais Bp Ew284 Where To Get Software And Cable Eventuallto Transfer
to transfer data to pc,ready to buy if works.
to transfer data to pc,ready to buy if works.
(Posted by salvtali 8 years ago)
How Where To Get Software (and Cable) For Bpew284,my Email: [email protected]
(Posted by stonyst 8 years ago)
Recharging Cable Will Not Charge Mic
The plug to recharge that goes in the base is either too loose or too tight?
The plug to recharge that goes in the base is either too loose or too tight?
(Posted by sewalker 8 years ago)
Do You Have Software( Special Cable Perhaps)for Ew284 Blood Pressure So Print Da
(Posted by stonyst 10 years ago)
Da7 Master Output Mute....?
i hav Ramsa da7 i hav some problem with my da7 i'll try to factory reset then master output is mute....
i hav Ramsa da7 i hav some problem with my da7 i'll try to factory reset then master output is mute....
(Posted by modernstyle96 11 years ago)