Maytag MVWC400XW Support Question
Maytag MVWC400XW Support Question
Find answers below for this question about Maytag MVWC400XW.Need a Maytag MVWC400XW manual? We have 3 online manuals for this item!
Question posted by brdjohn3 on October 7th, 2013
Maytag Centennial Mvwc400xw2 Warranty
I have had this washer for only a year and a half. Two days ago, it started smoking and now does not spin. Is this covered by the warranty?
Current Answers
Related Maytag MVWC400XW Manual Pages
Installation Instructions - Page 2
...and Parts Gather required tools and parts before starting installation.
Install your washer to improve performance and minimize noise and possible "washer walk". To order, please refer to 1"... Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (...
Installation Instructions - Page 3
... 20-100 psi (138-690 kPa). Floor standpipe drain system
IMPORTANT: Do not install, store, or operate washer where it will be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Water remaining in washer after use may cause damage in .2 (155 cm2)
1" (25 mm)
1" (25 mm)
3" (76 mm)
Dimensions show recommended...
Installation Instructions - Page 4
... plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with a qualified electrician if you start: remove shipping materials It is necessary to the instructions included with a power supply cord having a 3 prong grounding plug. If your washer includes a sound shield, please refer to remove all shipping materials for proper operation. n If codes...
Installation Instructions - Page 5
...
Drain hose form
Firmly grasp power cord plug and pull to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from rear panel. do not force excess ... shown in picture) or over console to allow free access to move washer later.
4. Drain hose form must be inside standpipe; For a laundry tub or standpipe drain, go to remove all parts from tub
Connect ...
Installation Instructions - Page 6
...amount of hose failure, replace the hoses every 5 years.
Connect inlet hoses to water faucets
Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to tighten couplings an ... ring. Do not use tape or sealants on valve when attaching to washer correctly. Connect inlet hoses to washer
Attach hose to water faucets with new inlet hoses with separate directions....
Installation Instructions - Page 7
... top edges of front using lid, as needed. Level Washer
IMPORTANT: Level washer properly to raise the washer. Check levelness of washer. If washer is level, use a 9/16" or 14 mm open -end or adjustable wrench to prop washer with beaded tie strap. Rock washer back and forth to laundry tub leg, drain standpipe, or inlet hoses for...
Installation Instructions - Page 8
...
recommended amount of /recycle all packaging materials.
q Check that all of washer. q To test and clean your Washer User Instructions. Select any tape
remaining on washer.
Start washer and allow to see what was skipped. Plug into washer basket or detergent dispenser (on . q Check that washer is an extra part, go back through steps to complete full...
Owners Manual - Page 2
WASHER SAFETY
2
Owners Manual - Page 3
...Expect
At different stages of the wash cycle, you start the cycle, the lid will lock, and the washer will not see a washer basket full of water as with low-water washplate ...the "Cycle Status Lights" section.
When loading the washer with a regular non-HE detergent. Low-water washing creates excessive sudsing with dirty laundry, fill it evenly around the basket wall. You will...
Owners Manual - Page 4
...If the sensing light is on your laundry load. This process may be added ...spinning, it may notice sounds or pauses that are different from traditional washers. Unlike traditional washers, the load is pressed, the washer will add additional agitation and soak time to "Yes" if using fabric softener. Press and hold 3 sec to the load. SENSING
When the START/Pause/Unlock button is not covered...
Owners Manual - Page 5
...
To allow for proper water removal, based on . The sensing process will start over when the washer is locked and cannot be added if the Fabric Softener Added-Yes option was spinning at increasing speeds for proper load sensing and spinning, the lid will lock and the Lid Locked light will be opened. If...
Owners Manual - Page 7
...longer cycle times and reduced rinsing performance. Add a measured amount of detergent to your laundry
2. IMPORTANT: Use only High Efficiency detergents. Loose change, buttons, or any small object....
• Mend rips and tears to avoid further damage to the bottom of the washer basket before adding clothes.
7 Sort and prepare your garments.
Using regular detergent will be...
Owners Manual - Page 8
... around the washplate; Do not use more than 1 cup (250 mL). Load laundry into the basket or on using the Downy Ball® call 1-800-688-7638 or visit www.downy.com. Tightly packing can lead to start the washer.
load them in the same cycle with liquid chlorine bleach. For questions on...
Owners Manual - Page 12
...operation for leaks (laundry tubs, drain pipe, water pipes, and faucets.)
Washer not loaded as...washers are removed during the spin/drain cycles. See "Using Your Washer" for optimal cleaning. In Canada www.maytag.ca
If you have started the washer. Feet may splash off tub. See "Level the Washer...expected
Not enough water in washer
Load not completely covered in loose heaps evenly around ...
Owners Manual - Page 13
... is added.
Close lid and press Start/Pause/Unlock.
Do not add more than 1 or 2 additional items after cycle has started to reduce suds. Check that may hear...SPIN. Remove several items, rearrange load evenly in inlet hoses, which can slow or stop the washer. Suds from regular detergents can restrict water flow. http://www.maytag.com/help -
This is power to the washer...
Owners Manual - Page 14
...and follow detergent directions based on . Inlet valve screens on load after washer has started.
14
Cycles with lower spin speeds remove less water than 96" (2.4 m) above the floor. This... hot and warm washes. http://www.maytag.com/help -
Washer not loaded as expected (cont.)
Washer not draining/ spinning, loads are still wet, or spin light remains on (indicating that inlet ...
Owners Manual - Page 15
...load after washer has started. Load ...maytag.ca
If you experience
Possible Causes
Solution
Washer not performing as recommended. Washer not loaded as expected (cont.)
Sand, pet hair, lint, etc. Washer is tangling
Washer...laundry off the washplate, resulting in water. Add detergent, oxi products and color-safe bleach to match your load with dry items only. Not using a higher speed spin...
Owners Manual - Page 16
... items only. Close the lid. The washer will damage fabrics.
http://www.maytag.com/help - Liquid chlorine bleach may not have been damaged before starting wash load.
Always read and follow the... lid will not unlock until the basket has stopped spinning. This may still be spinning. Fabric damage can occur if washer is started.
Do not pour liquid chlorine bleach directly onto load...
Owners Manual - Page 17
... purchase.
6. You will pay for future reference. MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Maytag brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Maytag") will need to be repaired in your...
Energy Guide - Page 1
Clothes Washer Capacity: Standard
Maytag Model: MVWC400X* Cat.
V0Ws7DFA(3B)
Estimated Yearly Operating Cost
(when used with an electric water heater)
$14
▼
$10
$71
Cost Range of Similar Models
128 kWh
Estimated Yearly Electricity Use
$9
Estimated Yearly Operating Cost
(when used with a natural gas water heater)
Your cost will depend on your utility rates and...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Top-load HE washer with Dispenser Drawers - video
... than your water heater can make sure that the rubber gaskets are in Corners Washer will not fill or start -up the available hot water faster than I expect - Is the water heater a...distance from the washer? Are you have hot water, and then begin a load of laundry. Washing many loads in Bravos High Efficiency washer is not working correctly - Top-load washer Warm or hot ... -
Wash light remains on - Top-load HE washer with Dispenser Drawer
...one incoming source of the drainpipe covered in High Efficiency Top-load and Front-load washers - Using the U-shape drain hose...Installation Instructions), will not fill or start to the washer and turned on. Top-load HE washer with tape. Straighten the hoses....) less than 4.5" (113 mm) into the drainpipe or laundry tub. Top Load HE with Dispenser Drawer - The drain hose... -
How do I remove odors from my Top-loading HE washer? Top-load HE with Dispensing Drawer
... dispenser. the lid will lock, and the cycle will dispense in your washer. Your washer has a Clean Washer cycle, which should be cancelled by pressing the Power button once. If the Clean Washer cycle is rinsed from the washer. Press Start. - The cycle will begin and water will continue. Always do the...
Similar Questions
My Washer Washes But Would Not Go Through The Spin Cycle. What Could The Problem
My washer washes but would not go through the spin cycle. What could the problem
My washer washes but would not go through the spin cycle. What could the problem
(Posted by shekeil2001 6 years ago)
Maytag Washer Model Mvwc400xw Making A Buzzing Noise Wont Start
(Posted by pehCarm 10 years ago)
My Maytag Centennial Ecoconserve Top-loading Washer, Model Mvwc400xw, Will Not
spin.
spin.
(Posted by Lisco 10 years ago)