Maytag MVWC400XW Support Question
Maytag MVWC400XW Support Question
Find answers below for this question about Maytag MVWC400XW.Need a Maytag MVWC400XW manual? We have 3 online manuals for this item!
Question posted by kiowaTer on August 28th, 2013
Maytag Centennial Washer How To Unlock Lid
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MVWC400XW Manual Pages
Installation Instructions - Page 2
...
Level
Wood block
Ruler or measuring tape
Pliers that open to toll-free phone numbers on back page of your washer in the top of your Use and Care Guide. INSTALLATION REQUIREMENTS
Tools and Parts Gather required tools and parts before...location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686 mm)
42" (1067 mm)
2...
Installation Instructions - Page 3
... 285863) that may be inside standpipe or below 32° F (0° C). install no higher than 96" (2.44 m), you need.
Top of laundry tub must support washer's total weight (with spacing of washer. To order, please see toll-free phone numbers in your Use and Care Guide for a standpipe drain: 2" (51 mm). n A grounded electrical...
Installation Instructions - Page 4
... moving it is recommended that a qualified electrician determine that a separate circuit breaker serving only this time.
4 n This washer is taped shut.
2. n If codes permit and a separate ground wire is used, it and make sure lid is equipped with a qualified electrician if you start: remove shipping materials It is required.
Remove shipping base...
Installation Instructions - Page 5
... 6. Free power cord
If clamp is not already in place on bottom of drain hose should be used.
5 For a laundry tub or standpipe drain, go to drain port
Remove tape from washer lid, open lid and remove cardboard packing tray from rear panel. Drain hose form must be inside standpipe;
Be sure to move...
Installation Instructions - Page 6
... a few seconds through hoses into a laundry tub, drainpipe, or bucket to hot water faucet. IMPORTANT: Do not overtighten or use tape or sealants on washer. In most standard configurations, hoses will ...to a cold water faucet, you are found.
11. If you must be connected to faucets or washer. Damage can result. HELPFUL TIP: Make note of hose failure, replace the hoses every 5 years.
...
Installation Instructions - Page 7
... on feet until they are about 4" (102 mm) with floor. Tighten leveling feet
Jam nut
With washer in its final location, place a level on leveling feet tightly against washer cabinet. Check levelness of front using lid, as a guide to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with wooden block.
When...
Installation Instructions - Page 8
.... q Check that you have all packaging materials. q Check that yellow shipping materials were completely
removed from console and any cycle.
q To test and clean your washer, measure 1/2 of normal
recommended amount of your Washer User Instructions. Plug into a grounded 3 prong outlet. Close lid. q Check that water faucets are now installed.
16.
Owners Manual - Page 3
... cycle, the lid will lock, and the washer will find a step-by-step description in the basket.
This is the low-water washplate wash system.
It may take several minutes before water is needed.
Choosing the Right Detergent
Use only High Efficiency detergents. Low-water washing creates excessive sudsing with dirty laundry, fill...
Owners Manual - Page 4
...water flowing through the dispenser, adding detergent to select a cycle for your laundry load.
Rather than what your previous washer provided.
• E ven in a cool water wash, some warm ...pause the cycle and unlock the lid. SENSING
When the START/Pause/Unlock button is spinning, it may change at different stages in an agitator-style washer, this washer delivers the detergent directly...
Owners Manual - Page 5
.... Fabric softener will be opened. SPIN
The washer spins the load at high speed. The sensing process will unlock once the washer movement has stopped. Some cycles will come on the selected cycle and spin speed.
Press START/ Pause/Unlock again to open the lid, press START/Pause/Unlock. DONE
Once the cycle is complete, this...
Owners Manual - Page 7
... suds for tips and more information on using an Oxi or color-safe bleach laundry boost product, add to the bottom of detergent to items during washing. HE detergents are made to determine the amount of the washer basket before adding clothes.
7
See "Cycle Guide" for the best performance. Synthetics, knits, and...
Owners Manual - Page 8
... on your wash cycle.
8 Close the lid and press the START/Pause/ Unlock button again to choose your load size. Turn cycle knob to start the washer. Then select Fabric Softener Added-Yes option....not overfill, dilute, or use color-safe bleach or Oxi products in the rinse cycle. Load laundry into washer. Do not use more than 1 cup (250 mL). Do not use of the fabric ...
Owners Manual - Page 9
...speed. If lid is added to assist in soil removal and to ON.
9 This will unlock once the washer movement has stopped.
Select cycle options, if desired
Press the START/Pause/Unlock button to ...has finished, the DONE indicator will hear the hum of metal hooks, zippers, and snaps. Unlocking the lid to add garments If you select a cycle, select the desire wash temperature by turning the ...
Owners Manual - Page 10
... are found. WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer where it will continue. If cycle must be interrupted, Press and Hold START/Pause/Unlock for a moment and pause, lid will lock, unlock, then cycle will not freeze.
Select CLEAN WASHER cycle.
5. Use a soft, damp cloth or sponge to reduce the risk...
Owners Manual - Page 11
... the following
recommended procedure:
To use , vacation, winter storage, or moving .
3. Use only HE High Efficiency detergent. Keep lid taped until washer is placed in washer or reconnect power.
3.
TRANSPORTING YOUR WASHER
1. Unplug power cord.
5. If you do not have packing tray, place heavy blankets or towels into a pan or bucket.
Disconnect and drain...
Owners Manual - Page 12
...minutes before washing. The washer senses load sizes and adds correct amount of water for leaks (laundry tubs, drain pipe, water pipes, and faucets.)
Washer not loaded as coins could... for proper installation:
Washer not level. Water can cause basket to be unbalanced.
In Canada www.maytag.ca
If you have started the washer.
http://www.maytag.com/help
Clicking or...
Owners Manual - Page 13
... lid and press Start/Pause/Unlock.
TROUBLESHOOTING
First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions) to possibly avoid the cost of cycle.
To remove suds, cancel cycle. In Canada www.maytag.ca
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Washer won't run .
Washer...
Owners Manual - Page 14
... higher than your load. Incorrect or wrong wash Check for proper installation.
http://www.maytag.com/help - Check drain hose for proper water supply. Use only HE detergent. In Canada www.maytag.ca
If you experience
Possible causes
Solution
Washer not performing as recommended. Check plumbing for small items.
Using a cycle with dry...
Owners Manual - Page 15
...Load with the best cycle.
Incorrect dispenser operation
Clogged dispenser. http://www.maytag.com/help - In Canada www.maytag.ca
If you experience
Possible Causes
Solution
Washer not performing as recommended. Select a cycle with the best cycle. Reduce ... chlorine bleach in water.
Added water lifts the laundry off the washplate, resulting in less effective cleaning.
Owners Manual - Page 16
...Lid locked light is flashing
The lid is tightly packed.
The lid will damage fabrics. This may have been damaged before washing. http://www.maytag.com/help - Fabric damage can occur if washer...A cycle was stopped or paused using the Start/Pause/Unlock button.
In Canada www.maytag.ca
If you experience
Possible Causes
Washer not performing as cycle is started. Solution
Empty pockets...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Washer will not fill or start - Top-load HE washer with Dispensers in Corners
... must be connected to be closed during the cycle? Straighten the hoses. Is the indicator on some models only) Your washer will cause the load to pause the washer and unlock the lid. The lid must be as visible as it , if necessary. If the problem continues to completely open both the... -
Washer will not fill or start - Top-load HE washer with Dispenser Drawer - video
... there power at the plug? The washer will unlock briefly before water is not opened and closed during load sensing and to 3 minutes before locking again. Re-select your desired cycle and press Start. Washer will not fill or start a new cycle. If the lid is added to the load. ... -
How do I open the lid?- Top-Load HE with Dispenser Drawer
... minutes if the load is flashing - This will unlock once washer movement has has stopped. Press the Power button to resume the cycle. How do I open the lid?- Top-Load HE with Dispensers in the power cord. To unlock lid: Plug in Corners Lid lock light is spinning at high speed. Front-load...
Similar Questions
Maytag Centennial Washer Mvwc400xw How Long Does Self Cleaning Cycle Take
(Posted by nanro 9 years ago)
Maytag Centennial Washer Mvwc400xw Problems Won't Drain
(Posted by samsDean69 10 years ago)
Repair Service Manual For Maytag Centennial Washer Mvwc400xw How To Fix Lid
lock
lock
(Posted by Trairoli 10 years ago)
