Maytag MVWC200XW Support Question
Maytag MVWC200XW Support Question
Find answers below for this question about Maytag MVWC200XW.Need a Maytag MVWC200XW manual? We have 3 online manuals for this item!
Question posted by Anonymous-95701 on January 25th, 2013
Driver Belt Part Number?
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MVWC200XW Manual Pages
Installation Instructions - Page 2
To order, please refer to toll-free phone numbers on back page of your Use and Care Guide.
Install your washer to 19⁄16" (39.5 mm)
Optional tools:
Flashlight
Bucket
Parts supplied:
NOTE: All parts supplied for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648...
Installation Instructions - Page 3
...level floor with water and load) of laundry tub must install higher than 96" (2.44 m) from bottom of washer. Consider allowing more than 96" (2.44 m) from bottom of washer. install no higher than 4.5" (113...spacing of drain hose should be purchased separately. To order, please see toll-free phone numbers in temperatures below the top of 20-100 psi (138-690 kPa). IMPORTANT: To ...
Installation Instructions - Page 4
.... A time-delay fuse or circuit breaker is required.
NOTE: To avoid floor damage, set washer onto cardboard before moving it at this appliance be plugged into a mating, 3 prong, grounding-...type outlet, grounded in the neutral or ground circuit.
48" (1.2 m)
Move washer to a gas pipe.
Set washer upright.
Move washer
n A 120 volt, 60 Hz., AC only, 15- n Do not have ...
Installation Instructions - Page 5
... standpipe; NOTE: Keep tray in standpipe
Drain hose form
Firmly grasp power cord plug and pull to back of washer.
4.5" (113 mm)
Place hose into standpipe or lay on elbow end of laundry tub. Squeeze clamp with clamp. Gently place power cord over end as shown in Step 7. Free power cord
If...
Installation Instructions - Page 6
... to faucets or washer. Connect inlet hoses to water faucets
Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to inlet valves. Connect inlet hoses to washer
Attach hose to tighten...to hot water to help in attaching hoses to hot water inlet valve marked with flat washers (not provided). Damage can result. Water should run until it is seated on valve...
Installation Instructions - Page 7
... turn jam nuts clockwise on feet until they are about 4" (102 mm) with beaded tie strap.
Secure drain hose
Laundry Tub
Standpipe
Wall
14. Rock washer back and forth to check levelness of washer.
HELPFUL TIP: You may want to turn jam nuts counterclockwise on top edges of sides. Tighten leveling feet
Jam...
Installation Instructions - Page 8
...
Complete Installation CHECKLIST
q Check electrical requirements. If there is plugged into a grounded 3 prong outlet. Plug into washer basket or detergent dispenser (on washer. q Dispose of/recycle all of washer. q Remove protective film from back of your Washer User Instructions. q Check that you have all packaging materials. Close lid. Select any tape
remaining on some...
Owners Manual - Page 2
WASHER SAFETY
2
Owners Manual - Page 3
... the Fabric Softener-Yes option was selected. press again to select available cycles on your previous washer provided.
• E ven in the cycle.
At each stage of cycles.
4 FABRIC ...on all features and options are different from traditional washers.
RINSE
You will hear the agitator moving the load. Press and hold for your laundry load. You may notice sounds or pauses that...
Owners Manual - Page 4
... only.
NOTE: Be sure to select Fabric Softener-Yes, if adding fabric softener to drain washer after cancelling a cycle or completing a cycle after power interruption.
Use this cycle for heavily ...High Use this cycle to complete a load after a power failure. SPIN
LID LOCKED
The washer spins the load at high speed.
This light indicates that best fits the load being washed....
Owners Manual - Page 5
..., and corduroy fabrics will pick up lint from towels, rugs, and chenille fabrics. If using an Oxi or color-safe bleach laundry boost product, add to avoid pilling.
USING YOUR WASHER
1. Add detergent
• Empty pockets. Helpful Tips:
• When washing water-proof or water-resistant items, load evenly.
• Use mesh...
Owners Manual - Page 6
Load laundry into washer. Items need to move freely for correct amount of liquid fabric softener. always follow manufacturer's....
3. For best results, do not pack the load tightly. IMPORTANT: Do not tightly pack or force items into washer
5. Then select Fabric Softener-Yes option. Adding Liquid Fabric Softener Manually to ensure proper distribution of the fabric softener during...
Owners Manual - Page 7
...delayed for smaller loads and Super Plus will pump out automatically. You will unlock once the washer movement has stopped. Select OPTION (on your load. This will light.
This may be ...option.
10. Delay in soil removal and to check for more than what your previous washer provided. Items need to save energy.
Wash Temp
Suggested Fabrics
Hot
Some cold water is ...
Owners Manual - Page 8
... storing or moving , or not using liquid chlorine bleach, add 1 cup (250 mL) to ensure bleach has been rinsed from washer. To winterize washer: 1.
Press START/Pause/Unlock. Water will pour into washer for a period of bleach to avoid damaging product over time.
3. If cycle must be interrupted, press START/Pause/Unlock twice...
Owners Manual - Page 9
... a medium-size load.
9
Reconnect water inlet hoses. Use half the manufacturer's recommended amount of washer.
4. Unplug power cord.
5. REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use washer again:
1. Drape power cord over lid and down front of washer. If you do not have packing tray, place heavy blankets or towels into a pan or...
Owners Manual - Page 10
... is normal. Wash smaller loads to basket could be out of alignment and cause water to drainpipe or laundry tub.
Check that inlet valve screens have water flowing to the washer.
Adding wet items to washer or adding more water to reduce imbalance. Empty pockets before water is on . This is uneven, a 3/4" (19...
Owners Manual - Page 11
...96" (2.4 m) above the floor.
Check drain hose for balanced spinning. Remove any blown fuses. Washer will pause during certain phases of the load in basket, and add detergent.
Cycles with lower spin... wetter than cycles with a low spin speed. To remove extra suds, select Rinse & Spin. Washer may be tightly packed. Do not interrupt cycle. Small items may hear the hum of a service...
Owners Manual - Page 12
... be on load after washing
Using too low a load size/water level selection. This washer uses cooler wash and rinse water temperatures than those using a higher speed spin.
Always ...valve screens on load after cycle
High speed spins extract more moisture than traditional top-load washers.
Load garments in loose heaps evenly around the basket wall.
This includes cooler hot and...
Owners Manual - Page 13
...as expected (cont.)
Not cleaning or removing stains (cont.)
Using too much detergent. Unload washer as soon as cycle is tightly packed. Lid locked light is flashing
The lid is started... or fill with the best cycle.
See "Cleaning your load with the lid open. The washer will damage fabrics. Always measure detergent and follow manufacturer's directions based on top of a service...
Owners Manual - Page 14
... or to parts or systems resulting from warranty coverage.
4. Dealer name Address Phone number Model number Serial number Purchase date
14 ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. ...required to Maytag within 30 days from the date of purchase.
6. MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major ...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
How to remove odors from a front-load washer without a Clean Washer cycle.
... drying of odor in your laundry room is soil that the Affresh cleaner removed from the washer. Pressing Pause/Cancel twice will turn off the washer. Use warm or hot water in my front-load washer How do I clean my Epic® Enter Model Number How do I find my model number? Repeat the cleaning procedure monthly... -
Washer fills slowly - Epic® front-load washer
.... To test for details connecting inlet hoses. Make sure the washer is not cleaning laundry - Front-load Neptune® Top-load washer Are both faucets for the door to side. The amount of ...turned on the washer clogged? The water level will not be as visible as it was in your product model number in the back of water. Reinstall hoses, turn on this washer should seem low... -
Leaking water - Top-load washer
...drain - enter your product model number in the washer basket. Evenly distribute the load in...washer). enter your product model number in the drainpipe. Check to the faucet. Make sure that the household drain is level front to back and side to side, and the lock nuts on the agitator (center in the search tool below to find them online. Check the household plumbing (laundry...
Similar Questions
Maytag Washer Mvwc200xw Stays On Sensor And Won't Cycle
(Posted by jioph 9 years ago)
Problems With Maytag Washer Mvwc200xw Lock Light Blinking, But Wont Fill
(Posted by Bendha 10 years ago)