Maytag MVW6230RHW Support Question
Maytag MVW6230RHW Support Question
Find answers below for this question about Maytag MVW6230RHW.Need a Maytag MVW6230RHW manual? We have 2 online manuals for this item!
Current Answers
Answer #1: Posted by SonuKumar on February 26th, 2023 9:23 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
The error message "Close Lid to Start" on your Maytag MVW6230RHW washing machine is an indication that the lid is not properly closed. This is a safety feature built into the machine to prevent any accidents or injuries during the wash cycle.
To resolve this issue, you should make sure that the lid is securely closed. Check to see if there are any obstructions, such as clothing or other objects, preventing the lid from closing properly. If there are, remove them and try again.
If the lid is properly closed and the error message persists, you may need to check the lid switch. The lid switch is a small sensor that detects whether the lid is closed or open. If the switch is faulty or damaged, it can prevent the machine from starting even if the lid is closed. In this case, you may need to contact a professional technician to diagnose and repair the issue.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Maytag MVW6230RHW Manual Pages
Owners Manual 1 - Page 2
...
You can be killed or seriously injured if you what the potential hazard is the safety alert symbol. Always read and obey all safety messages.
WASHER SAFETY
Your safety and the safety of injury, and tell you don't follow instructions.
We have provided many important safety messages in this manual and...
Owners Manual 1 - Page 3
...
Parts supplied:
NOTE: All parts supplied for installation are in cardboard insert in the top of the washer. Pliers that open to 13/4"
4" min. INSTALLATION REQUIREMENTS Tools and Parts
Gather required tools and parts before starting installation.
Tools needed (Not supplied with washer):
Wood Block
Ruler or measuring tape
Inlet hoses with flat...
Owners Manual 1 - Page 4
... drain system
5" (127 mm)
24 in .2 (310 cm2)
See requirements for installation with cable tie.
4 Top of laundry tub must install higher than 96" (2.44 m) from bottom of 0" (0 mm) clearance on carpet is your washer in low temperatures.
See the "Winter Storage Care" section for closet door ventilation openings which are required...
Owners Manual 1 - Page 5
... grounding-type outlet, grounded in accordance with a qualified electrician if you start: Remove shipping materials. Do not remove ground prong.
Move washer
ʍʍ A 120 V, 60 Hz., AC only, 15 or...is recommended that the ground path is taped shut.
2. Tip washer back and place on floor behind washer. it and make sure lid is adequate.
ʍʍ Do not ground to within ...
Owners Manual 1 - Page 6
... sure to drain port
Remove tape from washer lid, open lid, and remove cardboard packing tray from rear panel. Attach drain hose to remove all other packaging materials from tub
Connect Drain Hose
5. Squeeze clamp with pliers and slide black elbow end of laundry tub. Gently place power cord over console to allow free...
Owners Manual 1 - Page 7
... run until it is connected to hot water to help in attaching hoses to faucets or washer.
Make note of water may need to hot water inlet valve marked with separate directions. Clear... Damage can result. Repeat this step with second hose for a few seconds through hoses into a laundry tub, drainpipe, or bucket to inlet valves. Connect inlet hoses to water faucets
Run water for ...
Owners Manual 1 - Page 8
... shown. Check levelness of front using lid, as a guide to prop up the front of washer
Place level here
Place level here
If washer is level, skip to reduce excess ...shock. Do not use an adapter. Level Washer
IMPORTANT: Level washer properly to step 15.
Plug into a grounded 3 prong outlet. Not Level
LEVEL
Not Level
15. Secure drain hose
Laundry Tub
Standpipe
4.54".5" (114 mm)
...
Owners Manual 1 - Page 9
... your inlet hoses, mark the date of replacement on . ❑❑Check for leaks around faucets and inlet hoses. ❑❑Remove protective film from washer.
9 Close lid. Start washer and allow to begin the
cycle. Cleaning the Inside of your tools. ❑❑Check that shipping materials were completely removed from...
Owners Manual 1 - Page 10
...with a damp cloth and towel dry. Close the washer lid. After this procedure. If your washer, you are not removable. Push 2... at a level above could cause washer damage over time. f. Touch and hold the START/PAUSE button to water pressure surge....Washer Cycle Operation: 1. This cycle will be interrupted, touch POWER.
Unplug or disconnect power to model) You may find laundry...
Owners Manual 1 - Page 11
... HE (High Efficiency) detergent. Disconnect drain hose from drain system and drain any remaining water into washer basket. 7. disconnect and drain water
inlet hoses. 2. Shut off both water faucets; Place inlet hoses and drain hose inside washer. Close lid and place tape over edge and into a pan or bucket. Failure to follow WINTER STORAGE...
Quick Reference Sheet - Page 1
...hours.
DEEP FILL Touch to add more details.
Opening the lid cancels "Remote Enable". DELAY START Touch to delay the start cycle.
Touch during a cycle to modify the cycle's ...lid, which automatically pauses the cycle, and add items. To resume, close the lid and hold the START/PAUSE button to start the washer again.
4 START/PAUSE Touch and hold the START/PAUSE button to start...
Quick Reference Sheet - Page 2
...THE WASHER
4 SELECT THE DESIRED CYCLE FOR YOUR LOAD*
5 ADJUST CYCLE SETTINGS, IF DESIRED*
6 SELECT ADDITIONAL OPTIONS*
7 TOUCH AND HOLD START/ PAUSE... agitator-style washer. AUTO SENSING & DEEP FILL ■ The washer will not see a washer basket full of laundry products to ... drain if water level becomes too high or if the lid is active the cycle control knob will illuminate. ■...
Quick Reference Sheet - Page 3
...Speed: Water Level:
Cycle Details:
Overly soiled garments, items that cycle will be shown in washer
Clean Washer
with affresh®
Hot Warm Cool Cold Tap Cold
Hot Warm Cool Cold Tap Cold
Hot ...higher water level than other fabric types. Use with enough water to wet down the load before starting cycle.
Place small items in Bold. Use this cycle to wash lightly soiled items indicating "...
Quick Reference Sheet - Page 4
After time has expired, water will drain, but the washer will be shown in Bold. GET THE MAYTAG™ APP AND GET CONNECTED
With your...internet
please download the Maytag™ App and press REMOTE ENABLE. Items to allow remote control and interaction.
4 The washer will be guided through the steps to subscribe and create your user account to connect to soak small spots of soiled ...
Quick Reference Sheet - Page 5
... Enable
Faucet
Status Off Off
Off Low Medium High
Off On Off
5 Image
Description Door Locked
WASHER ICONS
Status Alert State
Image
Remote Enable
On
Delay Start
On
Deep Fill
On - Auto High
On - Auto
On - Max Fill
Fabric Softener
On
Extra Rinse
On
Smartgrid, Peak rates in effect
On Smart Delay...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The cycle time is not correct - Bravos washer with agitator
... time is necessary and may occur several attempts to redistribute the laundry load in balancing the load. Does the time displayed show one... selection, and household water temperature and pressure. Load-sensing Energy Star top-load washer with agitator Not filling or not starting - Bravos washer with agitator is using less detergent in future loads to aid in the drum... -
Washer will not fill or start - Top-load HE washer with Dispensers in Corners
.... The wash action turns on the washer clogged? Allow the cycle to start a new cycle. If the lid is wet, there may not start. The following illustrates how your desired cycle and press Start. Is the lid open . Close the washer lid before starting - Once the load is not opened and closed after the selected hours of... -
Washer will not fill or start - Bravos washer with agitator
...;3 prong outlet. Check to completely open . Close the washer lid before starting - Is a water inlet hose kinked? Is the washer in a normal pause in Corners The lid must be space for up with agitator will not start - Cancel the current cycle. Not filling or not starting the washer. Are you using Auto Water Level? Turn off...
Similar Questions
I Am Having A Problem With My Washer And Don't Know Where To Start.
So I came home today from the grocery store to see the load I left was still submersed in water. I c...
So I came home today from the grocery store to see the load I left was still submersed in water. I c...
(Posted by jredondo0705 10 months ago)
My Washer Is Not Draining As Well. Clothes Are Really Wet When Wash Is Complete
the washer had the wiring case replaced as a warranty repair. Ever since it doesn't drain as well as...
the washer had the wiring case replaced as a warranty repair. Ever since it doesn't drain as well as...
(Posted by Jennifersheaves 2 years ago)
Maytag Neptune Washer Mah6500aww Lights Blink But Won't Start
(Posted by sbeTamm 9 years ago)
Maytag Neptune Washer Door Latch Won't Close Tightly
(Posted by zdiski 10 years ago)