Maytag MHW4200BG Support Question
Maytag MHW4200BG Support Question
Find answers below for this question about Maytag MHW4200BG.Need a Maytag MHW4200BG manual? We have 5 online manuals for this item!
Question posted by townleyscott0 on June 14th, 2014
Control Panel Frozen, And Now Electrical Buzz
Hell, I set up my washer and started my first load. An error message showed up - sorry I don't remember which one. I turned the machine off. Now it will not turn on. When plugged in only "door locked" light lit up and there is an audible electrical buzz when plugged in, and the control panel is unresponsive when pushing any button.
Current Answers
Answer #1: Posted by TechSupport101 on June 15th, 2014 12:00 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. You should be able to obtain the best advice (Tech and Warranty) from here http://www.maytag.com/contact-us/ - preferebly the online Live-Chat.
Related Maytag MHW4200BG Manual Pages
Dimension Guide - Page 2
...power supply cord having a 3 prong grounding plug. n This washer is properly grounded.
n Check with a qualified electrician if you need to pump higher than 96" (2.44 m) from bottom of laundry tub must be plugged into a mating, 3 prong, grounding-type outlet, grounded in the neutral or ground circuit.
See "Alternate Parts".
ELECTRICAL REQUIREMENTS
n A 120 volt, 60 Hz...
Installation Guide - Page 3
... spacing for companion appliances and clearances for closet door ventilation openings which are required.
n A level floor with water and load) of 1" (25 mm) under counter installation:
3 Installing on washer, and water pressure of washer to 120° F (49° C). All dimensions show recommended spacing allowed, except for walls, doors, and floor moldings.
You will be large...
Installation Guide - Page 5
...installed by a qualified electrician. NOTE: To avoid floor damage, set washer onto cardboard before moving it is the personal responsibility and obligation ... upright position.
2. n This washer is equipped with a qualified electrician if you are not sure the washer is adequate. ELECTRICAL REQUIREMENTS WARNING
INSTALLATION INSTRUCTIONS
Electrical Shock Hazard Plug into a mating, 3 prong,...
Installation Guide - Page 6
... top
Loosen bolts with transport
bolt hole plugs
Remove the yellow shipping strap from the cord. Remove power cord
If clamp is transported at later date, call your local service center to avoid suspension and structural damage, a certified technician must properly set up washer for relocation.
6 For a laundry tub or standpipe drain, go to...
Installation Guide - Page 7
...drain hose. Coupling
B.
HELPFUL TIP: Make note of laundry tub. Attach the hose labeled hot to tighten couplings an additional two-thirds turn. IMPORTANT: Do not overtighten or use old hoses. C...it is connected to hot water to faucets or washer. Do not use hoses without washers.
11. IMPORTANT: Only 4.5" (114 mm) of laundry tub. Repeat this step with separate directions. Place...
Warranty Information - Page 1
...LAUNDRY...consequential damages, so these parts that prevent function of the washer and that is operated and maintained according to instructions attached...and maintained according to instructions attached to or furnished with electrical or plumbing codes, or use or when it was ... to state or province to repair or replace appliance light bulbs, air filters or water filters. SECOND THROUGH ...
Use & Care Guide - Page 4
....
5 DELAY START Use + and -
For lightly soiled and delicate fabrics, use the Soil Level setting to most loads, use + and -
to set the delay time to "0," or touch POWER/CANCEL.
6 CYCLE STATUS LIGHTS For details, see "Cycle Status Lights".
7 OPTIONS Touch to select available cycles on your load. B Extra Rinse Activate this feature as well. NOTE: The control panel features...
Use & Care Guide - Page 5
..., however, the Fresh Spin™ option is turned on or off -
Once the door has locked the second time, the washer will stay on using a steam boost for 3 seconds. This compartment cannot dilute powdered bleach. Cycle Status Lights
Delay If a Delay Start is set . The sensing light will periodically tumble the load after the wash cycle. Follow the manufacturer...
Use & Care Guide - Page 7
... uses a higher water level.
Large load: Fill the washer drum up . For best results, avoid packing tightly.
7 n Not all settings are labeled on the control panel.
Use this cycle with an empty wash tub. See "Washer Care." This cycle should not be used together. See "Washer Care" in the washer during the Clean Washer with affresh® cycle. NOTES...
Use & Care Guide - Page 8
... on the control panel. The certification verified that best fit the load being washed. Not all settings are available with Extra Rinse
Wash Temperature:
N/A
Extra Hot Hot
Warm Cool Cold
Spin Speed:
Soil Level:
Extra High
N/A
Med
Low
Extra High Extra Heavy
Med
Med
Low
Light
Available Options:
Fresh Spin™ Delay Start
Fresh Spin™...
Use & Care Guide - Page 9
... bags. Washer door should close easily.
Separate lint-takers from lightly soiled.
Items need to move freely for a medium-size load. n Mix large and small items and avoid washing single items. Load evenly. For multiple items, use more than one bag and fill bags equally.
9
This initial cycle serves to adding laundry products. Load laundry into fabric. n Turn knits...
Use & Care Guide - Page 11
....
11. To adjust a setting, touch its name - Adjusting settings will show the default settings for details on cycle features.
9.
to set the delay. Touch and hold START to 12 hours. Steam for available options and settings.
11 Tightly packing the load, unbalanced loads, or excessive suds may choose the DELAY START option. This will delay the start
The display will change...
Use & Care Guide - Page 12
... water leaks.
Touch START once;
To set the washer so that the Fresh Spin™ option does not come on garments. NOTE:
n The door will unlock once the washer movement has stopped. the door will remain locked while the Fresh Spin™ option is lit. Then close door and touch and hold again to remove the load promptly, use the...
Use & Care Guide - Page 14
... on the washer once. 2. The washer will begin to drain and rinse away the remaining
cleaning chemistry. 3. The cycle will remain locked until it may find some residue buildup in washer, then slide...either repeat the Clean
Washer cycle or to adequately rinse any spills. Lift off cover panel by pulling straight up to 30 minutes for damage to subsequent loads of laundry or to
remove the...
Use & Care Guide - Page 17
... - In Canada www.maytag.ca for leaks (laundry tubs, drain pipe, water pipes, and faucets.)
Only use HE detergent.
Noises
Clicking or metallic noises Door locking or unlocking. Empty pockets before washing. Water Leaks
Check the following for an HE front load washer. Water or suds leaking from washer" in firm contact with a few extra items...
Use & Care Guide - Page 18
... not add more than 1 or 2 additional items after cycle has started to provide a high concentration of tumbling and soak. washer stops working
Both hoses must be stopped to inlet valve. Check electrical source or call . Replace any kinks in washer drum. Door must be turned on. Some cycles feature periods of detergent for about 2 minutes during...
Use & Care Guide - Page 19
....
19 The door will not unlock
Door locks when cycle has started.
This is on. Do not add more than 96" (2.4 m) above the floor.
The load may not have both washer and faucet, ... if the end is lit, touch START once. or rinse temperatures
Washing many loads. Check that inlet valve screens are completed, the door must be opened between the washer drum and the outer ...
Use & Care Guide - Page 20
...washer to move freely for best cleaning. Washer not loaded as expected (cont.)
Desired setting or option does not light
For best performance, not all settings are not reversed. Load with a few extra items.
Washer not loaded... must be out of garments being washed.
The washer will start to redistribute the load.
Add load loosely.
The wash water was not warm enough ...
Use & Care Guide - Page 21
...washer has a tight seal to avoid chlorine bleach and fabric softener staining. Solution
Use a higher soil level setting and warmer wash temperature to measure correctly. Avoid overfilling.
Be sure to improve cleaning.
Use cycle designed for heavily soiled loads. Wipe up bleach spills. Sort dark clothes from whites and lights...the wash is started.
Fabric Damage
Sharp...
Use & Care Guide - Page 23
... of your authorized Maytag dealer to repair or replace appliance light bulbs, air filters or water filters. Service calls to determine... NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. MAYTAG® LAUNDRY LIMITED WARRANTY
This Maytag Limited Warranty supersedes and replaces the limited ... with electrical or plumbing codes, or use of the washer and that vary from state to state ...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
When to change the water filter - Side by side refrigerator
... changed ? side by pressing and holding the FILTER button for additional instructions and location of your particular filter status light/indicator in fresh food compartment Resetting the water-filter-status indicator light Changing/removing the water filter Animation - On some models) located on the temperature control panel or on usage and water quality. Decreased water... -
My gas oven won't operate
... electronic oven control set ? Repeat to release air from the display. Turn on the display. Surface burners fail to avoid unintended use of the surface burner knobs to unlock. To Lock/Unlock control: Before locking, make sure the oven and Timer are off. Is this the first time the oven has been used? Oven Error messages - On some... -
The door will not open - Front-load washer
... door locked and the Add A Garment or Add Clothes light on , then the washer door will unlock after the final spin, then the door will not start - If the Add A Garment or Add Clothes light is on ? Display shows F22 or FdL - If water remains in the washer after the Pause/Off or Pause/Cancel button...
Similar Questions
Maytag Washer Control Locked Light Promblems Machine Wont Start
(Posted by tsekp 9 years ago)
Pushed Power Button, Pushed Start Button. Door Locks Washer Does Not Start...
previously it gave me an error code e somethng f something, not sure, now not even that.
previously it gave me an error code e somethng f something, not sure, now not even that.
(Posted by sandib10566 9 years ago)
Maytag Washer Lid Locked Light Wont Come On
My lid locked light won't come on. Washer won't turn on.
My lid locked light won't come on. Washer won't turn on.
(Posted by carroli50 11 years ago)
How Do I Get Change That Has Fallen Into Bravos Washer Top Load Mvwb450wq0
how do I get change that has fallen into Bravos washer top load MVWB450WQ0, i noticed change in the...
how do I get change that has fallen into Bravos washer top load MVWB450WQ0, i noticed change in the...
(Posted by wolhare1 12 years ago)
New Install. Lid Lock Light On And Washer Won't Fill
We jsut installed our new washer and trying to start our first load. The lid lock light is on and th...
We jsut installed our new washer and trying to start our first load. The lid lock light is on and th...
(Posted by bkadha232 12 years ago)