Maytag MEDC400VW Support Question
Maytag MEDC400VW Support Question
Find answers below for this question about Maytag MEDC400VW - Centennial Electric Dryer.Need a Maytag MEDC400VW manual? We have 2 online manuals for this item!
Question posted by dawnrusko on November 21st, 2011
Wheres The Thermal Fuse Located
The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Maytag MEDC400VW Manual Pages
Owners Manual - Page 1
...
Keep this book and your appliance.
These words mean:
DANGER
You can find this manual and on the model and serial number label, located at the top inside dryer door well. We have provided many important safety messages in this information on your sales slip together for inwarranty service.
Dealer name
Serial...
Owners Manual - Page 2
IMPORTANT: The gas installation must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54. The dryer must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70.
2
Owners Manual - Page 3
... electrical switch;
WHAT TO DO IF YOU SMELL GAS:
• Do not try to the dryer plays a big role in good air flow.
■■ Replace plastic or foil vent material with heat, dryers ...from the entire length of who installed the dryer. each load.
■■ Use the shortest length of re or explosion, or to efficiently dry laundry.
When cleaning is detected, follow the "...
Owners Manual - Page 6
..., read the IMPORTANT SAFETY INSTRUCTIONS before each load.
The signal is selectable. Do not dry anything flammable on the back wall of fire, electric shock, or injury to On.
7.
WARNING: To reduce the risk of the dryer. The drum turns, but the drying rack does not move. Slide rear pegs into the...
Owners Manual - Page 7
...place.
2. Wet a nylon brush with a damp cloth. 3. Cleaning the Dryer Interior
1. Tumble a load of laundry in dryer.
Clean lint screen.
Do not rinse or wash screen to remove lint. ... screen firmly back into place.
See "Cleaning the Lint Screen."
7 DRYER CARE
Cleaning the Dryer Location
Keep dryer area clear and free from items that contain loose dyes, such as denim...
Owners Manual - Page 8
...; Has a household fuse blown, or has a circuit breaker tripped? Cap the open on some models)
1. The drum may be turning, but you may vibrate if not properly installed. Moving care - For direct-wired dryers:
WARNING
3. Replace the bulb with a 10-watt appliance bulb only. Electric Dryers
For power supply cord-connected dryers: 1. Locate the light bulb...
Owners Manual - Page 9
... contacting the sensor strips. Do not use a plastic vent. Run the dryer for the types of dryer cycles requires temperatures above 45ºF (7ºC).
■■ Is the dryer located in a room with lint? Use 4" (102 mm) diameter vent material.
■■ Is the dryer located in a closet? Failure to dry quickly? ■■ Is the...
Owners Manual - Page 10
.... The odor will not transfer to finish before removing laundry from the dryer before Cool Down may have an odor. Select a ...rewash, and dry the clothing.
■■ Is the electric dryer being used ?
Allow the Cool Down cycle to other clothing...(686 mm) Ultra Capacity side swing door only
Load is located? Accessories
Enhance your garments. Stains on high? Fabric softener ...
Owners Manual - Page 11
...the "Assistance or Service" section or by Maytag.
5. MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when ...warranty gives you specific legal rights, and you need it is located in accordance with electrical or plumbing codes, or use or when it . If you...repair house fuses, or to the appliance.
8. ITEMS EXCLUDED FROM WARRANTY
This limited warranty does...
Installation Instructions - Page 1
... killed or seriously injured if you what the potential hazard is the safety alert symbol. DRYER SAFETY
Your safety and the safety of Contents / Table des matières
DRYER SAFETY 1
INSTALLATION INSTRUCTIONS 2 Tools and Parts 2 Location Requirements 2 Electrical Requirements -
This symbol alerts you to reduce the chance of injury, and tell you don...
Installation Instructions - Page 2
... vent)
■ Tape measure
Parts supplied:
Remove parts package from dryer. only, direct wire installations)
■ Tin snips (new vent installations)
■ Level
■ Vent clamps
■ Caulking gun and compound (for proper exhaust installation.
If using a power supply cord, a grounded electrical
outlet located within 2 ft (61 cm) of either side of a companion...
Installation Instructions - Page 3
...electrical installer.
■ To be sure that the ground path is your dealer.
■ Special provisions must be considered.
18"* (45.7 cm)
14" max.* (35.6cm) 48 in. 2 *
(310 cm2)
3"* (7.6 cm)
1" (2.5 cm)
29" (73.66 cm)
A
24 in mobile homes to introduce outside air into the dryer. Installation Clearances The location...branch circuit. A time-delay fuse or circuit breaker is suitable ...
Installation Instructions - Page 4
..., or an equipment-grounding conductor must be used when the appliance is properly grounded. Electrical Connection To properly install your dryer, you must determine the type of electrical connection you are in doubt as to whether the dryer is installed in a location where grounding through the neutral conductors. In the event of malfunction or breakdown...
Installation Instructions - Page 5
...Number 3394208. WARNING: Improper connection of dryer's final location.
Be sure wall receptacle is properly installed and grounded in accordance with the Canadian Electrical Code, C22.1-latest edition and all... International Certified Power Cord intended to whether the dryer is 5 ft (1.52 m) in a risk of electric shock. A time-delay fuse or circuit breaker is equipped with a qualified ...
Installation Instructions - Page 6
... terminal block cover. Strain relief tab pointing up and the other is pointing up B. Strain relief tab pointing down screw location E. U.S.A.
Disconnect power before making electrical connections. Securely tighten all electrical connections. Disconnect power. 2. Install strain relief. Clamp section D. Hold-down
6 Hole below terminal block opening
3. Tighten strain relief screws...
Installation Instructions - Page 7
... Put the threaded section of electrical connection: 4-wire (recommended)
3-wire (if 4-wire is not available)
7 Hole below the terminal block opening. Electrical Connection Options
If your type .../240-volt minimum, 30-amp, dryer power supply cord*
4-wire connection: Power supply cord
4-wire direct
5" (12.7 cm)
3-wire receptacle (NEMA type 10-30R)
A fused disconnect or circuit breaker box*
...
Installation Instructions - Page 8
...wire) D. ¾" (1.9 cm) UL listed strain relief E.
Direct wire cable must have completed your electrical connections. B. Neutral ground wire
3. External ground conductor screw B. Now go to outer terminal block screws. ...to external ground conductor screw. Tighten screw.
Strip 5" (12.7 cm) of dryer rear panel. Shape ends of wires into slot of outer covering from external ...
Installation Instructions - Page 9
... of terminal block cover into a hook shape.
1" (2.5
cm)
3¹⁄₂" (8.9 cm)
When connecting to the center, silver-colored terminal screw of dryer rear panel. You have completed your electrical connections. Spade terminals with hold -down screw.
6. Neutral (white or center wire)
E A
A. Neutral ground wire B. Center silver-colored terminal block screw D. Connect...
Installation Instructions - Page 10
...outer terminal block screws. Tighten strain relief screw.
5. You have completed your electrical connections. External ground conductor screw B. Neutral ground wire C. Tighten strain relief...terminal block screw D. 1. A BC
A
E
D
A. Tighten screw. Place the hooked ends of dryer rear panel. Secure cover with hold -down screw.
6. Grounding path determined by a qualified electrician
...
Installation Instructions - Page 15
... been pushed firmly.
■ Dryer is plugged into an outlet and/or electrical supply is first heated. The odor will not start the dryer.
2. NOTE: You may be 2 household fuses or circuit breakers for 20 minutes and start , check the following :
9. Set the dryer on power. Check the dryer's final location. If the dryer will go back through...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Dryer does not heat - Electric dryer
... or has a circuit breaker tripped? If the problem continues, call an electrician. Enter Model Number How do I find my model number? Electric dryers use 2 household fuses or circuit breakers. The power supply cord may not have heat. Did you recently install a power supply cord on the control knob or button ... -
Steam nozzle has blue-green discoloration - Steam dryer
The Steam nozzle on the dryer drum Rusty racks/dishes in your dryer, (located inside the dryer, under the drum light) use white vinegar and scrub with a scouring pad. Dryer FAQs Knowledgebase search tips There are stains on my steam dryer has a blue-green discoloration. To clean any blue-green lime or calcium buildup off the... -
My dryer or load has an odor
... washer at the end of the wash cycle to avoid odors. Dryer Is the dryer being used for a long time will begin to grow mildew, which will be gone after the first cycle. A wet load left in the washer or dryer for the first time? (Electric dryers) A new electric heating element may have an odor.
Similar Questions
Where Is The Thermal Fuse Located On My Maytag Med9800tk0 Dryer?
(Posted by jschaeve1 9 years ago)
How To Check Thermal Fuse Maytag Centennial Dryer
(Posted by jimcque 10 years ago)
Where Is The Thermal Fuse Located On Maytag Centennial Dryer
(Posted by caal 10 years ago)
Where Is The Thermal Fuse Located On Maytag Centennial Medc400vw) Dryer?
(Posted by cool1ro 10 years ago)
Where Is The Thermal Fuse Located
(Posted by mwatsop 11 years ago)