Home » Maytag » Laundry Dryers » Maytag MEDC400VW

Maytag MEDC400VW Support Question

Find answers below for this question about Maytag MEDC400VW - Centennial Electric Dryer.
Need a Maytag MEDC400VW manual? We have 2 online manuals for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by mmhixon on November 20th, 2011

Sponge Down Lint Trap

Dropped a sponge down the lint trap. How can I get it out?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Maytag MEDC400VW Manual Pages

Owners Manual - Page 1

...safety messages in this manual and on the model and serial number label, located at the top inside dryer door well. W10287571A 1 This is , tell you how to know your complete model number and ... Numéro de téléphone Numéro de modèle Date d'achat DRYER SAFETY Your safety and the safety of purchase or installation date for future reference. Always read and...

Owners Manual - Page 2

The dryer must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. 2 IMPORTANT: The gas installation must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

Owners Manual - Page 3

...electrical switch; Follow the gas supplier's instructions. • If you cannot reach your gas supplier from the entire length of vent possible. ■■ Use no more information, contact your dryer... lint screen...laundry. When cleaning is detected, follow the Installation Instructions supplied with heat, dryers require good air flow to minimize the risk of who installed the dryer...

Owners Manual - Page 6

... Items containing foam, rubber, or plastic must be removed from dryer. Failure to rest on a clothesline or by using an Air Cycle. Clean lint screen before operating this to avoid wrinkling when you are unable ...60 min. 90 min. 6 Do not dry anything flammable on the back wall of fire, electric shock, or injury to ON or OFF. Load clothes loosely into the dimples on it (including cooking ...

Owners Manual - Page 7

... screen to remove residue buildup. 4. The lint screen is located where the dryer air exits your fingers. Pull the lint screen toward you should be on dryer usage. NOTE: Garments that would block the air flow for an extended period of clothes. This includes clearing piles of laundry in dryer. A screen blocked by a qualified servicer. Clean...

Owners Manual - Page 8

... the open on the supply line? ■■ Has a household fuse blown, or has a circuit breaker tripped? Unplug dryer or disconnect power. 2. Replace all parts and panels before servicing. Disconnect wiring. 3. Electric dryers use ? Electric dryers use 2 household fuses or circuit breakers. See the Installation Instructions. ■■ Is the clothing knotted or balled up...

Owners Manual - Page 9

... the Installation Instructions. ■■ Is the exhaust vent diameter the correct size? Failure to check air movement. Lint on Automatic Cycles. Use 4" (102 mm) diameter vent material. ■■ Is the dryer located in death or re. ■■ Is the exhaust vent or outside exhaust hood to do not feel...

Owners Manual - Page 10

...Was the load removed from the area, rewash, and dry the clothing. ■■ Is the electric dryer being used ? Select a lower temperature, and use an automatic drying cycle. fits 29" (737 mm...the end of the cycle. Accessories Enhance your dryer is too hot ■■ Were laundry items removed from the dryer before removing laundry from dryer. ft. (0.18 cu. side swing or ...

Installation Instructions - Page 1

... and others are not followed. U.S.A. Puede encontrar el número de modelo y de serie dentro de la cavidad superior de la puerta. 29" (73.7 CM) ELECTRIC DRYER INSTALLATION INSTRUCTIONS INSTRUCTIONS POUR L'INSTALLATION DE LA SÉCHEUSE ÉLECTRIQUE DE 29" (73,7 CM) Table of others . Canada...

Installation Instructions - Page 2

...that all parts were included. 4 leveling legs Parts needed: Check local codes, check existing electrical supply and venting and see "Electrical Requirements" and "Venting Requirements" before starting installation. Place dryer at temperatures below 45ºF (7ºC). See "Electrical Requirements." ■ A sturdy floor to water and/or weather. Check code requirements. Failure...

Installation Instructions - Page 3

....66 cm) D A. Wide opening . Recessed area B. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening side-swing door D. The National Electric Code requires a 4-wire supply connection for homes built after 1996, and all local codes and ordinances. A time-delay fuse or circuit breaker...

Installation Instructions - Page 4

... at least 4 ft (1.22 m) long, must have 4 10-gauge solid copper wires and match a 4-wire receptacle of NEMA Type 14-30R. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the neutral conductor. ■ A 4-wire power supply connection must be using a power supply...

Installation Instructions - Page 5

... and ordinances. The cord is equipped with all local codes. Connect to be plugged into an appropriate outlet that the electrical connection is within reach of the line. Canada WARNING ■ This dryer is 5 ft (1.52 m) in accordance with a CSA International Certified Power Cord intended to an individual branch circuit. 4-wire receptacle...

Installation Instructions - Page 7

...direct wire cable through the strain relief. Neutral prong E. Spade terminals with the dryer cabinet and be in a horizontal position. Now complete installation following instructions for ... ends F. ¾" (1.9 cm) UL listed strain relief G. Removable conduit connector B. Electrical Connection Options If your type of the strain relief through the hole below terminal block opening...

Installation Instructions - Page 8

...Tighten screw. Direct wire cable must have completed your electrical connections. Cut 1¹⁄₂" (3.8 cm)...12.7 cm) of direct wire cable under center, silvercolored terminal block screw. Ground wire (green or bare) of extra length so dryer can be moved if needed. External ground conductor screw - Strip insulation back 1" (2.5 cm). Tighten screw. Neutral wire (white ...

Installation Instructions - Page 9

...-colored terminal block screw D. Tighten screws. 4. Direct wire cable must have completed your electrical connections. Strip insulation back 1" (2.5 cm). A B C 1. External ground conductor screw... relief 3. Strip 3¹⁄₂" (8.9 cm) of outer covering from end of dryer rear panel. Now go to "Venting Requirements." 3-wire connection: Direct Wire Use where local...

Installation Instructions - Page 10

... terminal block screw D. Tighten screws. 4. Insert tab of terminal block cover into slot of dryer rear panel. Connect a separate copper ground wire from external ground conductor screw. Remove center silver...) UL listed strain relief F. You have completed your electrical connections. Loosen or remove center silver-colored terminal block screw. 2. Tighten strain relief screws. 5.

Installation Instructions - Page 11

... an existing vent system ■ Clean lint from your dealer or by calling the toll-free number listed on the cover of the Dryer User Instructions. DURASAFE™ venting products are.... ■ 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. If this dryer MUST BE EXHAUSTED OUTDOORS. Clamp Exhaust Recommended hood styles are recommended. Elbows 45° elbows provide better ...

Installation Instructions - Page 12

... many varieties. Housecleaning problems and health problems. Plan Vent System Choose your installation. Dryer B. Wall D. Over-the-top installation (also available with rigid metal or flexible ... G. Vent length necessary to the manufacturer's instructions. Improper venting can cause moisture and lint to collect indoors, which may be in the path of the exhaust (such as...

Installation Instructions - Page 15

... there is first heated. NOTE: You may be 2 household fuses or circuit breakers for the dryer. When the dryer has been running or "On" position. ■ Start button has been pushed firmly. ■ Dryer is plugged into an outlet and/or electrical supply is an extra part, go away. 15 Complete Installation 1. Set the...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Dryer does not heat - Electric dryer
... Air Fluff or Air Only temperature option? Expect loads dried with the other temperature selections. Has a household fuse blown or has a circuit breaker tripped? dryer does not dry Dryer does not heat - The drum may not have heat. Loads are damp; Electric dryer My electric dryer does not heat. If the problem continues, call an electrician.
My dryer or load has an odor
...after the first cycle. My dryer makes sounds or vibrations Fabric is located? The odor will result in the washer or dryer for the first time? (Electric dryers) A new electric heating element may have an odor... gone from the washer at the end of the wash cycle to avoid odors. Dryer My dryer or load has an odor Have you recently been painting, staining or varnishing in surrounding...
Dryer does not heat - Gas dryer
... gas shutoff valve in the supply line. The valve is open when the handle is closed. Electric dryer Expect loads dried with the other temperature selections. The drum of a gas dryer will turn, but the dryer will not , if the gas shutoff valve is parallel to the gas pipe. See the Installation...