Maytag MED9700SB Support Question
Maytag MED9700SB Support Question
Find answers below for this question about Maytag MED9700SB - 27" Front-Load Electric Dryer.Need a Maytag MED9700SB manual? We have 1 online manual for this item!
Question posted by buffalo73375 on July 22nd, 2014
Can I Use A 3 Instead Of 4 Prong Plug Without Damage. Wire Is 10 Gage In House
Moved into an older home with three prong dryer plug (50 amp) and 10 gage wire. Can I replace 4 prong cord with three without damaging dryer?
Current Answers
Answer #1: Posted by richsappliance on July 22nd, 2014 2:46 PM
richsappliance
Member since:
January 18th, 2014 Points: 91,150
Member since:
January 18th, 2014 Points: 91,150
Sure, no problem. The 4-prong just has an isolated ground wire. Just change the plug. See video below:
https://www.youtube.com/watch?v=54SpQftODZU
If I helped please "accept" my answer. Thanks.
Related Maytag MED9700SB Manual Pages
Use and Care Guide - Page 3
... spotted with controls.
■ Do not repair or replace any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have provided many important safety messages in this manual and on or in the dryer. This symbol alerts you to cooking oils in...
Use and Care Guide - Page 4
...storage drawer.
The pedestal will need to stack your dryer.
See "Electrical Requirements" and "Venting Requirements" before starting installation. To order, call the dealer from dryer drum.
The wires that connect to purchase a Stack Kit. Pedestal Height
Color
Part Number
10" (25.4 cm)
White
MHP1000SQ0
10" (25.4 cm)
Black
MHP1000SB0
15.5" (39.4 cm)
White
MHP1500SQ0...
Use and Care Guide - Page 5
...
*Required spacing
1"* (2.5 cm)
27" (68.6 cm)
1"* (2.5 cm)
5 Place dryer at temperatures below 45ºF (7ºC). If using a power supply cord, a grounded electrical outlet located within 2 ft
(61 cm) of either side of the dryer. At lower temperatures, the dryer might be exposed to support the total dryer weight of the dryer in longer drying times. The dryer must be considered...
Use and Care Guide - Page 7
... it is recommended that a qualified electrician determine that the electrical connection is adequate. If the dryer is permanently connected to install with a 4-wire electrical supply connection, the neutral ground conductor must determine the type of electrical connection you will be using and follow the instructions provided for Mobile Home Construction and Safety, Title 24, HUD Part 280...
Use and Care Guide - Page 8
... electrician.
If using a power supply cord: Use a UL listed power supply cord kit marked for electric current. The ground wire (ground conductor) may be at least 4 ft (1.22 m) long. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. Do not modify the plug on the dryer. The cord should contain: ■ A UL listed 30-amp power supply cord, rated 120...
Use and Care Guide - Page 9
... in doubt as to do so can result in death or electrical shock.
SAVE THESE INSTRUCTIONS
4-wire receptacle 14-30R
■ Do not use Power Supply Cord Replacement Part Number 9831317. Electrical Shock Hazard
Plug into an appropriate outlet that you use an extension cord.
9 Failure to whether the dryer is 5 ft (1.52 m) in the "Assistance or Service" section. Canada...
Use and Care Guide - Page 11
...)
Electrical Connection Options
If your home has:
And you will be in a horizontal position. Reaching inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be connecting to:
Go to Section
4-wire receptacle (NEMA Type 14-30R)
A UL listed, 120/240volt minimum, 30-amp, dryer power supply cord*
4-wire connection: Power supply cord
4-wire...
Use and Care Guide - Page 12
... being moved to "Venting Requirements."
4-wire connection: Direct wire
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. Neutral wire (white or center wire)
4. down screw. 7. B. Neutral ground wire
D. B
F
A
CD
E
G
A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. 4-wire connection: Power supply cord...
Use and Care Guide - Page 14
... type 10-30R) B. 3-wire plug C. Ring terminals G. Now go to "Venting Requirements."
3-wire connection: Direct wire
Use where local codes permit connecting cabinet-ground conductor to the terminal block, place the hooked end of the wire under the screw of extra length so dryer can be moved if needed. Direct wire cable must have completed your electrical connection. Neutral prong D. Insert...
Use and Care Guide - Page 15
... hooked end of the neutral wire (white or center wire) of direct wire cable under
the center screw of dryer rear panel. Insert tab of terminal block cover into slot of power supply cord/cable under the outer terminal block screws (hooks facing right). C A
B
D
Optional 3-wire connection
Use for direct wire or power supply cord where local codes do...
Use and Care Guide - Page 16
... Use a heavy metal vent. Do not use duct tape.
IMPORTANT: Observe all joints.
■ Exhaust vent must not be fully extended and supported when the dryer is not plugged with lint.
■ Replace ...Review Vent system chart. Good
Better
Clamps ■ Use clamps to seal all governing codes and ordinances.
B
4" 10.2 cm
4" (10.2 cm) heavy metal exhaust vent
Vent products can ...
Use and Care Guide - Page 17
...
Fire Hazard Cover unused exhaust holes with a magnetic latch. Dryer B. Clamps F. Exhaust outlet
17 Improper venting can cause moisture and lint to collect indoors, which may result in death, fire, electrical shock, or serious injury. The angled hood style (shown here) is acceptable.
4" (10.2 cm)
2½" (6.4 cm)
■ An exhaust hood should cap...
Use and Care Guide - Page 21
...the door and check that hold the handle bracket to scratch the dryer surface. Remove the 2 screws that it latches securely.
21 Align ... in the door opening covering the hinge mounting holes. Replace the 2 handle screws for fingerprints on the glass.
... at the bottom. Move hinge to remove the plug strip in Step 3. 6. Style 1: Remove the plug strip.
■ Use a small flat-blade...
Use and Care Guide - Page 22
... on power. In the U.S.A.
10. If you have not tripped. Turn on . ■ Household fuse is intact and tight, or circuit breaker has not tripped.
■ For power supply cord installation, plug into a grounded outlet and/or electrical supply is not crushed or kinked. 5. The odor will not start the dryer. Dispose of/recycle all...
Use and Care Guide - Page 27
... to complete drying. A
A. Front edge
2. Place drying rack inside dryer drum, positioning the back wire on top of the rack. Refer to the following chart). Rack Dry
Setting
Temp.
Dryer rack front edge B.
or +) buttons. To use automatic cycles with the drying rack. Dryer back panel
27 Put the wet items on the ledge of the...
Use and Care Guide - Page 28
...
Apply a liquid, nonflammable household cleaner to your load is in dryer. These stains are removed.
3. Clean the lint screen with powdered laundry detergent and very warm water. 2.
Apply paste ...Tumble a load of dye.
28 Wet lint is probably clogged if lint falls off the screen with the lint screen loose, damaged, blocked, or missing. Replace screen in the dryer. WARNING
...
Use and Care Guide - Page 29
... supply cord. 2. Use masking tape to secure dryer door. Disconnect power. 2. Use masking tape to secure dryer door. Open the dryer door. Remove the cover.
3. Plug in dryer base. 4.
Unplug dryer or disconnect power. 2. Make sure leveling legs are secure in dryer or reconnect power.
29 Changing the Drum Light
The dryer light automatically turns on dryer usage. Replace the cover...
Use and Care Guide - Page 30
...use ? Check that both fuses are too long, or load is the dryer level front to back and side to possibly avoid the cost of lint or replace exhaust vent with lint? Electric dryers use... to vibrate. Use only one fabric softener sheet, and use 2 household fuses or circuit breakers.
If the dryer hasn't been used ? Run the dryer for 2-5 seconds. Electric dryers require 240-volt...
Use and Care Guide - Page 32
..., you still need further assistance, you use only factory specified parts. For more high-quality items or to order replacement parts, we recommend that you can also...gas line dryer connector installation kit 4 ft (1.2 m) dryer cord, 3-wire, 30 amp 4 ft (1.2 m) dryer cord, 4-wire, 30 amp 6 ft (1.8 m) dryer cord, 4-wire, 30 amp Dryer vent lint brush All-purpose appliance cleaner Laundry supply ...
Use and Care Guide - Page 33
... purchased.
ITEMS MAYTAG WILL NOT PAY FOR 1. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use your major appliance, to replace or repair house fuses or to correct defects in remote locations. 10. This major appliance is designed to determine...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Surface burners fail to ignite
...dryer. Use a nonabrasive plastic scrubbing pad and mildly abrasive cleanser. If you do not have verified gas is available at the appliance, contact an authorized service company. Is the burner wet from one burner to correct house wiring...schedule a service call back to light and perform properly. Replace the burner cap, making sure the alignment pins are properly aligned ... -
Washer will not fill or start - Top-load HE washer with Dispenser Drawer - video
... fill. Select Drain & You will hear a click, the basket will not...cord plugged into a grounded 3 prong outlet. Do not use short slow spins to be tightly packed. Wash smaller loads. When the Start button is not opened and closed after the cycle has started ? Next, the washer will unlock briefly before starting - Check electrical... -
How to use oxi products in the washer? Top-load HE washer with Dispenser Drawer
...particular time in the washing process. How to remove residual water. video Damaged clothing - Can I use oxi product in washers. Dispenser not working correctly - How to add oxi ...other oxygen based product. Top-load HE washer with Dispensers in the washer? Read and follow the instructions below for a limited amount of laundry additives and dispense at the...
Similar Questions
3 To 4 Prong Cord
Dryer came with 3 prong cord. When I moved, I bought 4 prong cord, but don't know how to connect it ...
Dryer came with 3 prong cord. When I moved, I bought 4 prong cord, but don't know how to connect it ...
(Posted by leighs14ls 8 years ago)
Maytag Front Load Electric Dryer Won't Start
(Posted by nuriterry 9 years ago)
Maytag Electric Dryer Med9700sb0 Lights Come On But Dryer Wont Start
(Posted by rontal 9 years ago)
I Have A Maytag Front Loading Electric Dryer Model Med9600 Sq0. When I Attempt T
I have a Maytag front loading electric Dryer model MED9600 SQ0. When I attempt to start it by pressi...
I have a Maytag front loading electric Dryer model MED9600 SQ0. When I attempt to start it by pressi...
(Posted by wrzimmerly 10 years ago)
We Plug In Our Maytag Model Med9700sb And It Wont Turn On.
had a power surge and now the dryer wont power up.
had a power surge and now the dryer wont power up.
(Posted by Anonymous-89989 11 years ago)