Makita XPH03MB Support Question
Makita XPH03MB Support Question
Find answers below for this question about Makita XPH03MB.Need a Makita XPH03MB manual? We have 2 online manuals for this item!
Question posted by acfoster on December 14th, 2019
My Xph03 Now Drills Off Center
My XPH03 is only a couple of years old and now drills off center. The bit wobble as I drill making very inaccurate holes. Is this fixable with a replacement part.
Current Answers
Related Makita XPH03MB Manual Pages
XPH03Z Instruction Manual - Page 2
... entangled cords increase the risk of electric shock. A moment of inattention while operating power tools may ignite the dust or fumes. 3. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XPH03
Drilling into concrete
16 mm (5/8")
Drilling into steel
13 mm (1/2")
Capacities
Drilling into wood
76 mm (3")
Fastening wood screw
10 mm x 90 mm (3/8" x 3-1/2")
Fastening machine screw...
XPH03Z Instruction Manual - Page 3
...condition that can make exposed metal parts of moving parts.
16. avoid contact. GEB056-5
CORDLESS HAMMER DRIVER DRILL SAFETY WARNINGS
1. Wear ear protectors when impact drilling. Hold power tool by insulated ...for which it was designed. 18. Use the power tool, accessories and tool bits etc. Hold power tool by poorly maintained power tools. 22. Use of dust collection can be ejected ...
XPH03Z Instruction Manual - Page 4
...tool operation and charge the battery cartridge when you notice less tool power.
2. It may result in a container with product
(gained from rotating parts. 8. SAVE THESE INSTRUCTIONS. Always stop operating immediately. Keep hands away from repeated use) replace...not use a damaged battery. Hold the tool firmly. 7. Do not touch the bit or the workpiece
immediately after operation;
...
XPH03Z Instruction Manual - Page 5
...
1. Switch action
1. Battery protection system (Lithium-ion battery with a little click. The tool will not operate. Then pull the switch trigger again to draw an abnormally high current....Star marking
012128
Lithium-ion batteries with a star marking are placed under one of the tool, causing injury to slip off and the
battery cartridge is not locked completely. In this ...
XPH03Z Instruction Manual - Page 6
...before
operation. • Use the reversing switch only after releasing the trigger. If you operate the tool with hammering, turn the ring so that the speed change lever is in the light or see the...for your job. The lamp keeps on the ring. Reversing switch action
1. If you operate the tool with clutch, turn the ring so that the arrow points toward the mark on lighting while the switch...
XPH03Z Instruction Manual - Page 7
... capacity (specific country) Only for a particular application. LED indicator
2
1
012714
Stop the tool and with the pointer on the panel.
Installing or removing driver bit or drill bit
1. NOTE: • The adjusting ring does not lock when the pointer is required for tools with the pointer. Adjusting the fastening torque (screwdriver mode " ")
1. First, slide the...
XPH03Z Instruction Manual - Page 8
Installing bit holder
OPERATION
1. Bits 45 mm long can be installed on either side of the tool. Hook 3. Failure to the marking. Be sure to drill holes of the tool and potentially severe injury. Keep the tool in position and prevent it in the loss of control of uniform depth.
This can be resumed. Then proceed as it...
XPH03Z Instruction Manual - Page 9
... adjusting ring can be drilled dry. The guide screw makes drilling easier by setting the reversing switch to rest for this excessive pressure will not speed up
the drilling. The exceptions are obtained with wood drills equipped with a fresh battery. Limit mark
1
006258
Replace when they wear down device. • If the tool is a tremendous force exerted...
XPH03Z Instruction Manual - Page 10
... Service Center. • Drill bits • Hammer drill bits • Screw bits • Blow-out bulb • Safety goggles • Makita genuine battery and charger • Grip assembly • Depth rod • Hook • Rubber pad assembly • Wool bonnet • Foam polishing pad • Battery protector
MAKITA LIMITED ONE YEAR WARRANTY
Warranty Policy
Every Makita tool is...
XPH03Z Parts Breakdown - Page 2
...
A08
BL1840
A09
450128-8
A10
142147-5
XPH03 NAME PLATE HOUSING SET RUBBER PIN 6 HEX. FLAT HEAD SCREW M6X22 KEYLESS DRILL CHUCK 13 TAPPING SCREW 4X18 GEAR ASSEMBLY ...-7 INC. 2 GRIP ASSEMBLY GRIP 36 COMPLETE SQUARE BOLT M8X100 GRIP SPRING 60 GRIP BASE 60 THUMB SCREW M5X10 HEX. BIT 2-45 STOPPER POLE ASS'Y DC18RC FAST CHARGER BATTERY BL1840 SET BATTERY COVER PLASTIC CASE COMPLETE
1 1 PC. 2 PC...
Similar Questions
Stuck Drill Bit
After using a 1/2 inch SDS MAX bit for about 1/2 hour the bit is totally stuck and I dont know how t...
After using a 1/2 inch SDS MAX bit for about 1/2 hour the bit is totally stuck and I dont know how t...
(Posted by Anonymous-166285 3 years ago)
Drills Won't Work
I bought 4 used Makita drills at a garage sale from a builder. Model 6095D Seller explained that the...
I bought 4 used Makita drills at a garage sale from a builder. Model 6095D Seller explained that the...
(Posted by ghauser 6 years ago)
Model # 6223dwe Cordless Drill
the drill will only work with the battery insert part way. If I insert it all the way it goes dead. ...
the drill will only work with the battery insert part way. If I insert it all the way it goes dead. ...
(Posted by dsleonard76 6 years ago)
Repa[r Of A Hr5000 Drill
what parts are faulty when my drill does not hammer
what parts are faulty when my drill does not hammer
(Posted by Anonymous-139111 9 years ago)