Makita HR4041C Support Question

Find answers below for this question about Makita HR4041C.
Need a Makita HR4041C manual? We have 3 online manuals for this item!

Makita Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-87967 on December 8th, 2012

Makita Hr4041c

Where is the change lever switch located?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Makita HR4041C Manual Pages

Owners Manual - Page 2

... power tools that have the switch on . Use of a cord suitable for the connection of drugs, alcohol or medication. Personal Safety 9. Use safety equipment. Do not wear loose clothing or jewellery. Use the correct power tool for appropriate conditions will do the job better and safer at all instructions. ENGLISH SPECIFICATIONS Model HR4041C Capacities...

Owners Manual - Page 3

.... Wear ear protectors. Check for operations different from the power tool before use the power tool if the switch does not turn it under no one in the manner intended for lubricating and changing accessories. 25. Follow instruction for the particular type of the power tool is difficult. 8. Without proper warm-up the lubrication. Do...

Owners Manual - Page 4

... carrying out any position. ･ hertz ･ alternating current ･ no longer work on the adjusting dial and the revolutions/blows per minute. Speed change 1. Number on the tool. To start the tool, simply pull the switch trigger. Side grip (auxiliary handle) 1. Bit grease (optional accessory) Coat the bit shank head beforehand with this...

Owners Manual - Page 5

... the hole, then pull the switch trigger. Depth gauge 2. Keep the tool in position and prevent it until the red dots on the tool/bit at the desired location for drilling holes of hole break...the bit Press in the tool retainer and turn it to secure the bit. 1. Clamp screw 007799 007797 Set the change lever to clean the dust out of the tool and potentially severe injury. By...

Owners Manual - Page 6

... . Core bit 2. Then resume drilling. Chipping/Scaling/Demolition 007798 Set the change lever to the symbol. Hold the tool firmly with the core bit in the tool in the same manner as a drill bit. 1. Turn the tool on and apply slight pressure on the tool will not increase the efficiency. Adapter 2 003216 6 Pressing very hard on...

Owners Manual - Page 7

... Switch off and unplugged before attempting to perform inspection or maintenance. Send the complete tool to collect inside and replace with the bit end pointing upwards. Rest the tool ...Makita tool specified in the tightening direction. Rotate the change lever to persons. Rest the core bit on the concrete and turn the tool on the table with a fresh grease (60 g; 2 oz). Run the tool...

Owners Manual - Page 8

... to A-Taper adapter • Spline shank to SDS adapter • Blow-out bulb • Lock nut wrench 35 • Hex wrench MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from state to state. IN...

Parts Breakdown - Page 2

... F. SPRING 15, HR3851 H.S.H.BOLT M6X25, HM1211B TOOL HOLDER, HR4041C O RING 48, HR2511 X-RING 28, HR5000 NYLON WASHER 29, HR4041C FLAT WASHER 29, HR4041C IMPACT BOLT, HR4041C WASHER 17, HR4041C RUBBER RING 18, HR4041C SLIDE PLATE, HR4041C BARREL CPL.,HR4041C H.S.H. SPRING 35, HR4041C FLAT WASHER 34, HR4041C RING SPRING 32, HR4041C STRIKER, HR4041C O RING 22, HR4002 KEY 4, HR3851 SPIRAL BEVEL...

Parts Breakdown - Page 3

... 1 1 1 1 2 1 1 1 1 1 1 1 1 1 Page 3 of 3 8/18/2010 BOLT M6X20, LS1013 SWITCH LEVER, HR4041C SWITCH, HM1303B LEAD UNIT, HR4041C HANDLE CPL., HR4041C TAPPING SCREW, FLANGE 5X25, 5177B STRAIN RELIEF, HP1621F TAPPING SCREW 4X18, 4323K CORD (2X16X16 SJ), HR5000 CORD GUARD 10, HM1202C HANDLE COVER, HR4041C TAPPING SCREW 4X18, 4323K PLASTIC TOOL CASE,HR4041C DEPTH GAUGE, HR3851 MODEL NO. 69 70 70 71 72...

Flyer (English) - Page 1

... Fast Provides the end-user with Hammering"; 1,300-2,600 BPM No Hammering while Idling Helps Increase Tool Life Torque Limiting Clutch Disengages if Bit Jams DURABILITY High quality Aluminum housing for durability and longer tool life VERSATILITY HR4041C accepts spline shank bits for rotary hammering and 3/4" Hex 21/32" Round for "Hammering Only...

Flyer (English) - Page 2

...9632; Heavy-Duty Core Bits (See our latest catalog for maintenance STANDARD EQUIPMENT ■ Plastic Tool Case (158257-8) ■ Depth Gauge (321248-4) ■ Side Handle (158131-0) SPECIFICATIONS Capacities:...or visit makitatools.com Makita U.S.A., 14930 Northam St., La Mirada, CA 90638 All models and accessories subject to change without prior notice. Model HR4041C 1-9/16" ROTARY HAMMER...