Home » LiftMaster » Garage Door Openers » LiftMaster SW470

LiftMaster SW470 Support Question

Find answers below for this question about LiftMaster SW470.
Need a LiftMaster SW470 manual? We have 2 online manuals for this item!

LiftMaster Overview Questions Manuals Reviews Videos Research

Question posted by TimBaxter on May 3rd, 2016

Troubles Setting Up Master/second

Can someone give me a more detailed description of wiring up the second controller? The instructions are vague at best for this.Thanks

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related LiftMaster SW470 Manual Pages

SW490 GL BOARD Manual - Page 2

...it is unique, it . DESCRIPTION QTY. Because each application is...Wiring 21-22 Control Board Illustration 23 Controller Programming and Features 24-25 Program Settings 26-27 TROUBLESHOOTING 28-29 MAINTENANCE Operator Maintenance 30 Single Phase Wiring Diagram (SW470 31 Single Phase Wiring Diagram (SW490 32 Three Phase Wiring Diagram (SW490 33 Control... These instructions are ...

SW490 GL BOARD Manual - Page 4

... for secondary protection. UL325 MODEL CLASSIFICATIONS The SW470 and SW490 are the six types of entrapment... The opener can be used as a secondary protection. Type C: Inherent adjustable clutch or pressure relief valve. Constant pressure control. 4...III - In order to four single family dwellings, or a garage or parking area associated therewith. That means that the type ...

SW490 GL BOARD Manual - Page 9

...minimum Perpendicular Mount Operator 3" U-bolt (4 required) Power and control wiring should be run in separate conduit 9 pipe (2 req'd.) ... electrical conduit, as required, prior to the gate and fence is critical. 2. Set mounting post and electrical conduit in the operator. Figure 1 18.5" Fence 30" ...SW470) 1. Locate and anchor two posts made of the operator to pouring concrete. 3.

SW490 GL BOARD Manual - Page 12

... gate. Arm must swing approximately 2 degrees past straight position (See detail) ADVERTENCIA Crank Extension Extension arm installation detail NOTE: Dotted line indicates straight arm position PRECAUCIÓN GATE BRACKET INSTALLATION (SW470) 1. NOTE: As an alternative, (2) 3/8-16 bolts and a nut plate are tightened. Set the control arm stop as the top surface of gate 36" plate...

SW490 GL BOARD Manual - Page 14

...pin and pivot pin securing control arm to the operator (Figure 1). 2. I N S TA L L AT I O N CONTROL ARM ASSEMBLY (SW490) continued Gate Hinge Open gate position 2" 34" Closed gate stop D Control arm hub assembly Output Shaft...dimension. ** Cut excess control arm extension and/or control arm hub assembly for desired pivot to arm assembly. MANUAL DISCONNECT MODEL SW470 1. Weld or bolt...

SW490 GL BOARD Manual - Page 17

... OFFICE USE. Then follow the steps above to reprogram each remote control that will now operate when the push button on residential garage door openers because it overrides the safety reversal devices. WARNING Tested to opener (Figure 3). 2. WARNING ADJUSTMENT WARNING PROGCRAAMUMITNGIOTHNE RADIO RECEIVER SET SECURITY MODE The Universal Receiver can be used with up to 31...

SW490 GL BOARD Manual - Page 24

... amount of Motor Learn Routine *Hard inputs include open and close limits. If the unit activates a ...master and problem second during run time 5 Limit fault Control Input 6 Loss of communications Removal of the range. ADJUSTMENT CONTROL BOARD PROGRAMMING AND FEATURES MOTOR LEARN FUNCTION (FORCE PROFILE) This function is moving in stand alone mode. 1. FORCE CONTROL Set the force control...

SW490 GL BOARD Manual - Page 25

...DESCRIPTION On when Contactor A is activated On when Contactor B is activated On when SAM relay is activated On when Mag Lock relay is activated On when Alarm Relay is activated. ADJUSTMENT CONTROL... D24 D29 LED NAME Radio Shadow Hard Close Stop Soft Open Hard Open Interrupt (Safety) Loop Obstruction Open D31 Obstruction Close DESCRIPTION On when Radio switch is activated On when Shadow Loop ...

SW490 GL BOARD Manual - Page 27

... conduit as the power and control wiring. In this mode no response the operator will require a normally close cycle. The Second unit will operate in a master or second mode depending on (S4) switch setting. The motor learn function must be disabled. Master or Standalone Gate Setting Master Unit ON S4 Second Gate Setting Master Unit ON S4 TRAFFIC Second...

SW490 GL BOARD Manual - Page 29

...wire running smoothly. Review program settings pages 26-27 and check both the master and second for correct operation. Entrapment (Force Pot) incorrectly set... is programmed The open and close to the magnets located on position any power wiring. The master or second unit ... in the on the gearbox pulley as their wiring. Radio controls will indicate the activation of an active or ...

SW490 GL BOARD Manual - Page 31

..., IL 60125 DRAWING NUMBER: DATE: 7/29/03 01-G1978 REVISION: E ECN: 03-0401 31 COMMON SOFT OPEN NC "B" LIMIT CONTACTOR B NOTE 1 PRIMARY 24V SEC. SINGLE PHASE WIRING DIAGRAM (SW470) 1 PHASE POWER IN SWITCH NOTE 1 MOTOR GROUND GL CONTROL BOARD J2 PLUG 24 Vac - IN RPM - GND LOCK 1 LOCK 2 ALARM 1 ALARM 1 B+ ALARM ASSY 76-G0564...

SW490 GL BOARD Manual - Page 35

...removed from these lists. REPAIR PARTS - SW470 Refer to the number of individual components....parts available for Motor Molded Pulley 6" Chain, #40-53 Pitches Master Link, #40 Motor, 115V, 1PH, 1/2HP (Not Included...DESCRIPTION Mounting Bracket Reducer Bracket Motor Bracket Switch Box Cover Sensor Support Bracket On/Off Switch Hall Effect Sensor Assembly Alarm Assembly Side Cover Control...

SW490 S3 BOARD Manual - Page 4

...locations not intended to four single family homes or its garage or parking area. CLASS 4 ! ! COMMERCIAL/GENERAL ACCESS... 84-WH-38 85-FW-38 SW470 DESCRIPTION GATE OPERATIONAL SAFETY INSTRUCTION MANUAL STOP BUTTON ARM CHANNEL EXTENSION...FLAT WASHER 3/8-16 x 1 HEX HEAD BOLT 3/4-10 x 3 HEX HEAD BOLT 3/8-16 X 3/8 CONE POINT SET SCREW 3/4-10 HEX NUT 3/8 SPLIT LOCKWASHER QTY. 1 1 2 1 1 1 2 2 1 6 2 ...

SW490 S3 BOARD Manual - Page 12

...place. NOTE: Instructions are provided .... 2 Excavate required areas for conduit installation and mounting posts. 3 Set mounting post and electrical conduit in most swing gate installations, pad mounting is...Post Mount for right hand operator installation. SW470 gate operators have provisions for 3" pipe clamps (not supplied) are for SW470 Operator Only 1 Locate mounting post and ...

SW490 S3 BOARD Manual - Page 13

..., insuring that the operator is level and above pad. 5 Allow concrete to set at least two days before installing operator. 6 After concrete has set, carefully secure operator to concrete pad, in correct relative secure operator to the fence. " The SW470 may ONLY be installed perpendicular or parallel to the gate. The L-Bolts will...

SW490 S3 BOARD Manual - Page 17

... #1, pin #2 for left or right hand operation. Refer to Figure 14 to the desired fully opened position. 2 Loosed set screw on close the gate. TO ADJUST AUXILIARY OPEN LIMIT SWITCHES 1 Maintain gate in open position. 2 Loosen set screw on open limit cam. 3 Rotate the close limit cam in the same direction as the shaft turns to...

SW490 S3 BOARD Manual - Page 19

... level 1 (operator reverse to the bottom two pins, or move in either direction. The slave operator must be set the time for the master operator. RIGHT HAND/LEFT HAND ON = Left Hand (gate will open to the right) (Determine hand selection from bottom two pins (show illustration) to move all poles on 3 seconds...

SW490 S3 BOARD Manual - Page 22

...item is removed. Preliminary System Check Out Before adding any options, accessories or adaptions, it for proper open, stop and closing of all programs that the two (2) gate warning signs are secured to the ...and System Check-Out Manual Operation and System CheckOut SW470 Manual Gate Operation Remove the (2) black plastic knobs which secure the control arm assembly to adding on the outside.

SW490 S3 BOARD Manual - Page 24

...is pressed. All operator bearings are of phase. Symptom Motor does not run when OPEN or CLOSE button is important to note, however, that a binding or defective gate can severely... SW470 or SW490 operator will operate for cause. Remedy Replace fuses or reset breaker and check for many years with a minimum or service maintenance. programming. Inspect control station and all field wiring....

SW490 S3 BOARD Manual - Page 26

...DESCRIPTION PULLEY, MOTOR PULLEY, GEAR RUDUCER COMPRESSION SPRING ALUM. 26 SW470 Parts List and Drawing SW470 Parts List PART # QTY DESCRIPTION FOR 115 VOLT OPERATORS 20-2100 1 MOTOR 29-3530 1 CAPACITOR 74-SW4705011 1 SW470 S3 CONTROL...6-32, 3/8" HEX x 1/2"L #40 ROLLER CHAIN, 53 PITCH #40 MASTER LINK TRANSFORMER LIMIT SWITCH SPST TOGGLE SWITCH SWITCH BOX CAPACITOR CAPACITOR CLAMP GEAR ...