LiftMaster SL595 Support Question
LiftMaster SL595 Support Question
Find answers below for this question about LiftMaster SL595.Need a LiftMaster SL595 manual? We have 1 online manual for this item!
Question posted by Lsuttercane on October 11th, 2013
What Does One Flash On The Diagnostic Led Mean?
The person who posted this question about this LiftMaster product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related LiftMaster SL595 Manual Pages
SL595 Manual - Page 2
...installation check that
Program Settings 16 accompany it will alert you to your commercial door and gate operator unless you MUST read and fully understand this Signal Word on ...them carefully. Read them .
Model SL585 34 Repair Parts - Model SL595 36
ADVERTENCIA Electrical Box 37 Safety Accessories for Open Roller Gates 7 Warning Sign Placement 7
• DO NOT attempt ...
SL595 Manual - Page 3
... - 55 ft. (16.8 m)
37.7" (95.8 cm)
14.1" (35.8 cm)
12.9" (32.8 cm)
Opposite Gate Side
14.9" (37.9 cm)
MODEL SL595
• 1/2 HP Motor Maximum Gate Speed - 12"/sec. (30.5 cm/sec) Maximum Gate Weight - 1100 lbs. (499 kg) Maximum Cantilever Gate Width - ...)
Gate Side
16.5" (41.9 cm)
13.5" (34.3 cm)
22.5" (57.2 cm)
30" (76.2 cm)
Allow For Door Opening
12" Min. (30.5 cm)
3" (7.6 cm) Dia.
SL595 Manual - Page 4
... this operator. This entrance is installed on both the open and close directions of the four UL325 classes. That means that all installations must be designed, arranged or configured...can be used as a multi-family housing unit (five or more single family units) hotel, garage, retail store or other restricted access locations not servicing the general public, in which unauthorized access...
SL595 Manual - Page 5
...bottom edge.
b. The gate must be installed, one component. Swinging gates shall not open position. A minimum of two (2) WARNING SIGNS shall be supplied with the vehicular gate...or maintained systems can create high levels of force in contact with a separate access opening shall be located and its function as the perimeter reachable by building structures, natural ...
SL595 Manual - Page 6
...
Seal loops
1-1/2" (37 mm)
Loop wire layer 1/4" (6 mm) or larger depending on loop wire size
Photo eyes for open cycle
GATE SYSTEM (COMMERCIAL SLIDE GATE)
Telephone Entry System
Open Edge
Close Edge
Photo eye for open cycle
STREET
8' (2.4Inmt(eS)rarLufoepottyp)
Photo eye for close cycle
4' (1.2 m) Typical
4' (T1y.2pimca)l 4' (T1y.2pimcIan)tl(eSrarLufoepottyp...
SL595 Manual - Page 7
...and be guarded against at any time without prior warning. See Safety Brochure
Gate Edge for Open Direction
Gate Edge for Close Direction
for Close Direction
DO NOT MOUNT ACCESSORIES THAT ARE ACCESSIBLE... SERIOUS INJURY or DEATH from many fence suppliers. Also,
Photo Beam
for Open
UNIT
Direction
Additional Post Mounted Gate
Edge for Close Direction
WARNING Photo Beam for Close Direction...
SL595 Manual - Page 11
Remove the operator cover or open access door.
2" (5.1 cm) U-bolts
With Lock Washers
AVERTISSEMENT 3. Locate and engage the manual disconnect and lock it in line with each other. and Nuts
4. Do not overtighten ...
SL595 Manual - Page 12
... for engagement.)
Pull the handle to release
12 Release the lever and close the door. (Some operator output sprocket rotation may be properly phased. Secure all electrical power... is shipped from the factory as 3/4" and 1" knock outs for engagement.)
MODEL SL595 DISENGAGEMENT:
RE-ENGAGEMENT:
Open the hinged door and pull the disconnect lever and lock it in place. SINGLE PHASE All single ...
SL595 Manual - Page 13
After adjustment, release plate and ensure it trips the open or has difficulty opening .
It may become necessary to the fully closed position.
13 The sensor air gap should flash simultaneously for correct alignment. At the closed position, turn the power on , these LEDs should .010 - .015"
be used to its full closed position.
2. Locate...
SL595 Manual - Page 14
...- Terminals 10 & 5 -
Contact)
N.O.
This input will reverse an opening gate.
MODEL SL595
Pin
MODEL SL585
Pin
UL325 ENTRAPMENT PROTECTION
PRIMARY ENTRAPMENT PROTECTION ADJUSTMENTS Force Control Set...input will reverse a closing will have no effect. INSTALL VENT PLUG
1. Obstruction While Opening (Edge/Photo Eye Input) Edge Input: See Programming Section on page 15. Activating...
SL595 Manual - Page 15
...34
PH
PH
activating the interrupt (safety) loop, open
or override open . PHOTO CLOSE
CLED
OPED
WARN MAG
Close Photo Eye...open S2
limit when activated during the ON
close cycle.
The Timer-to -Close
Potentiometer Force Adjustment
Dip Switch #2 Dip Switch #1 Diagnostic LED
J2 Connector
J5 Connector SAMS
Relay Drive Troubleshooting LEDs
J1 Terminal Troubleshooting LEDs
15
Limit LEDs...
SL595 Manual - Page 16
...changes to take effect, the Save Mode switch must be in order to the right.
On an open command there will beep 3 seconds prior to -Close
feature works in motion" alarm feature. SL ...= Slide • SW = Swing
RIGHT/LEFT OPERATION
This switch selects the gate opening direction, to the left or to optimize gate behavior for specific application. Right/Left operation is ...
SL595 Manual - Page 17
...CLOSE STOP
Shadow Loop Input (N.O.)
Radio (Single Button) Input (N.O.)
FREQ FREQ
Soft Open Input (N.O.)
123 56
789 0#
Hard Open Override Control Input (N.O.)
OPEN CLOSE STOP
Interrupt (Safety) Loop Input (N.O.)
Obstruction While Opening Edge/Photo Eye Input (N.O.)
Obstruction While Closing Edge/Photo Eye Input (N.O.)
17 CONTROL CONNECTION DIAGRAMS
Accessory Terminal Block
24 Vac Accessory Power...
SL595 Manual - Page 18
... when it overrides the safety reversal devices. closed as long as the radio continues transmitting (Figure 2).
Use of children. Move the brown wire on residential garage door openers because it can be set at the HIGH position for each remote control remote control in safety. WARNING Connector
Antenna
Accessory Tray
WARNING
To prevent...
SL595 Manual - Page 19
... OPERATION
Output Duration Terminals
MOMENTARY Jumper OPERATION
Output Duration Terminals
Figure 3
OPENING RECEIVER
OPEN RECEIVER Connect Antenna
Indicator Light Learn Button
C
P2 M
24V
12V...Mode
Power Supply Jumper
NOTICE: To comply with FCC Standards FOR HOME OR OFFICE USE. Soft Open
These terminals are intended for each remote control. Control Conduit
Control Conduit
1 234 567
12 3...
SL595 Manual - Page 20
...will continue to Master/Second wiring. When two operators are intended for every query.
Close Override Control Input
Open Override Control Input 3 4 5 6 7 8 9
N.O. Com
enable the control to be completed ... Input
MASTER/SECOND SYSTEMS
Dual Gate Communications
The control board is applied to the open or close stop if there is active. NOTE: Do not run Master/Second communication...
SL595 Manual - Page 24
...adjustment nut on SL585/595 operators. Press the motor learn or some other error occurs the LED will run for this happens try learning while running . If this . SOLENOID ACTUATED BRAKE... be reprogrammed to flash rapidly.
3. This is obstructed.
4. An added feature of the brake is just enough tension to permit the operator to move the gate smoothly through a complete open or the close...
SL595 Manual - Page 25
... when Photo Eye Beam is reached. RELAY DRIVE TROUBLESHOOTING LEDS
There are 5 troubleshooting LEDs on for the open override, close limits.
These LEDs will be around the middle of the range. Two red LEDs (OLS, CLS) are closed. The LED is on previous page. LED Code Flashed
OFF 1 2 3
4
5 6
On No Flash
Diagnostic Meaning
Cleared By
Normal operation
Single entrapment sensed
Double...
SL595 Manual - Page 26
... in voltage. Remove the accessory and test the operator.
➤ If the open or interrupt (safety) loop LED is a master/second unit communication failure. This voltage should be wired incorrectly or...Replace the motor if it is not a major change in the operator check the yellow diagnostic LED at the operator should be within 5% of 24 Vac. TROUBLESHOOTING
FAULT
POSSIBLE CAUSE
FIX...
SL595 Manual - Page 27
... S1-1 on switch S1-1 ➤ If the switch S1-1 is not engaged.
Remove the accessory and test the operator.
➤ If the soft open or interrupt (safety) loop LED is programmed incorrectly
➤ The close by hand at the operator's main power switch. Apply power and
retest the operator. Make sure that...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 7 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Garage Door Opener Model
How do I know if I have a 3255 or 3255-2M garage door opener?
How do I know if I have a 3255 or 3255-2M garage door opener?
(Posted by ericoster1 3 years ago)
Noise From Garage Door Opener
I have a liftmaster garage door opener. It makes a loud screeching noise when the door is lowered....
I have a liftmaster garage door opener. It makes a loud screeching noise when the door is lowered....
(Posted by tom19097 10 years ago)
How Do I Program Liftmaster Sl595 To Open And Close Using Keypad Entry?
is this possible? want a pin to open and close gate.. dont want pushbuttons or remote.
is this possible? want a pin to open and close gate.. dont want pushbuttons or remote.
(Posted by Bourked 11 years ago)