LiftMaster SL595 Support Question
LiftMaster SL595 Support Question
Find answers below for this question about LiftMaster SL595.Need a LiftMaster SL595 manual? We have 1 online manual for this item!
Question posted by noezuniga on February 2nd, 2015
How Can I Program A Remote Control For Sl595 And Wat # ?
The person who posted this question about this LiftMaster product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related LiftMaster SL595 Manual Pages
SL595 Manual - Page 2
...Solenoid Actuated Brake 24
Friction Clutch 24
HARDWARE KIT SL585/SL595 (K77-34846)
Control Board Programming and Features 24-25
AVER
Troubleshooting 26-27 Self-Regulating...(SL585 & SL595 10
CAUTION Install Gate Bracket and Drive Chain 11
Available Conduit Access for Open Roller Gates 7 Warning Sign Placement 7
• DO NOT attempt repair or service of your commercial door and gate ...
SL595 Manual - Page 3
... - 55 ft. (16.8 m)
37.7" (95.8 cm)
14.1" (35.8 cm)
12.9" (32.8 cm)
Opposite Gate Side
14.9" (37.9 cm)
MODEL SL595
• 1/2 HP Motor Maximum Gate Speed - 12"/sec. (30.5 cm/sec) Maximum Gate Weight - 1100 lbs. (499 kg) Maximum Cantilever Gate Width - ...)
Gate Side
16.5" (41.9 cm)
13.5" (34.3 cm)
22.5" (57.2 cm)
30" (76.2 cm)
Allow For Door Opening
12" Min. (30.5 cm)
3" (7.6 cm) Dia.
SL595 Manual - Page 4
...control requiring continuous pressure to service the general public. A contact device such as a multi-family housing unit (five or more single family units) hotel, garage, retail store or other location not intended to operate the operator open... by security personnel.
This entrance is installed on both the open and close directions of gate travel. Both primary and secondary entrapment...
SL595 Manual - Page 10
... By Local Codes or Below Frost Line
SL595 ONLY
Figure 3
12" (30.5 cm) Minimum From Ground
Power and Control Wiring Must Be Run In Separate Conduit
SL595 ONLY
10
Drive and Idler Sprocket Toward ...
Drive and Idler Sprocket Toward Gate Side
Angle Bracket
3" (7.6 cm) U-bolt (4 required)
Power and Control Wiring Must Be Run In Separate Conduit
Figure 3
End Post Fence Line
8.5" (21.6 cm) 6" ...
SL595 Manual - Page 12
... connectors. MANUAL DISCONNECT
MODEL SL585 DISENGAGEMENT:
RE-ENGAGEMENT:
Rotate disconnect handle 90˚ to electrical wiring diagrams on page 8 for engagement.)
MODEL SL595 DISENGAGEMENT:
RE-ENGAGEMENT:
Open the hinged door and pull the disconnect lever and lock it in place.
Refer to disengage. On three phase operators, power connections must be required for...
SL595 Manual - Page 14
...While Closing (Edge/Photo eye with N.O. MODEL SL595
Pin
MODEL SL585
Pin
UL325 ENTRAPMENT PROTECTION
PRIMARY ENTRAPMENT PROTECTION ADJUSTMENTS Force Control Set the force control pot such that the unit will have no ... Programming Section on page 15. This input will reverse an opening gate. Terminals 10 & 5 - Obstruction While Closing (Edge/Photo Eye Input) Edge Input: See Programming ...
SL595 Manual - Page 15
... OPEN
CLED
OPED
WARN
MAG
Open Edge: When the control board is activated during the opening protection input.
PHOTO OPEN
CLED
OPED
WARN MAG
Open Photo Eye (Pause): When the
S2
control ... Troubleshooting LEDs
15
Limit LEDs
Programming Port (factory use only)
Motor Learn Button
J3 Connector Aux. UL325 ENTRAPMENT PROTECTION (CONTINUED)
EDGE/PHOTO OPEN
This switch (S2-3) selects ...
SL595 Manual - Page 18
... is prohibited on residential garage door openers because it
onto the "F"-connector provided on Terminal Block TB1 position 6 (from electrocution:
PROGRAMMING THE RADIO RECEIVER Set Security Mode
• Be sure power is PROHIBITED. operate in HIGH security mode.
AVERTISSEMENT remote controls or passwords in HIGH security mode. Repeat Steps 2
door.
AVERT
ADVERTENCIA RECAUCIÓ...
SL595 Manual - Page 19
... remote control is pressed. Within 30 seconds, press and hold the "learn " button on the receiver panel until the indicator light turns off (about 6 seconds). The opener will glow steadily for changing the code setting or replacing the battery. Accessories that you wish to operator (Figure 3).
2.
M
HIGH NORM
M
PROGRAMMING THE REMOTE TO THE RECEIVER
1. Pry open control...
SL595 Manual - Page 20
...
N.O. After Master/Second wiring has been completed and the S4 switch programmed, both units must be placed between 11 and 12 of the
12 3 456
gate. Terminals 4 & 5 (Com) - When two operators are intended for use with a loop detector.
Hard Open Override Control Input
These terminals are intended for longer than three seconds will...
SL595 Manual - Page 23
The gate MUST reverse on contact with gate controls. Disconnect ALL power BEFORE performing ANY maintenance.
9. SAVE THESE INSTRUCTIONS.... more frequent maintenance checks.
2. Never use separate entrance.
8. READ AND FOLLOW ALL INSTRUCTIONS.
2. Keep the remote control away from the gate. Have a qualified service person make repairs to adjust and retest the gate operator properly ...
SL595 Manual - Page 24
...AVERT AVERT ATTEN
AVER
Friction Clutch
CONTROL BOARD PROGRAMMING AND FEATURES
MOTOR LEARN FUNCTION (FORCE PROFILE)
This function is not an automatic reversing device. If either the open /close buttons. NOTE: Motor...screw that if the gate meets an obstruction, the clutch will run for accurate force control. If the LED goes out the motor is just enough tension to permit the operator...
SL595 Manual - Page 25
CONTROL BOARD PROGRAMMING AND FEATURES (CONTINUED)
FORCE CONTROL Set the force control pot such that the unit will complete a full cycle of ...) to blink out diagnostic codes.
Force Control
Max. LED
LED NAME
D11 D13 D15 D17 (Green) D19 D21 D24 D29
Radio Shadow Hard Close Stop Soft Open Hard Open Interrupt (Safety) Loop Obstruction Open
D31
Obstruction Close
DESCRIPTION
On when Radio ...
SL595 Manual - Page 26
....
➤ If the open or interrupt (safety) loop...2) Low primary (high voltage) power
➤ Remove all is good, replace the control board. The voltage at the operator should be within 5% of the operator's rating ...transformer.
➤ If both primary and secondary power is good, check to the programming dip switches.
3) An accessory is active or malfunctioning check the red input status...
SL595 Manual - Page 27
...entrapment sensor to provide feedback to the control board when the operator is moving. Remove the devices and retest. To make programming changes,
switch S1-1 off the unit's... the sensor if it is
WHEN STRUCK DURING
programmed incorrectly
OPENING
➤ The open obstruction input has been programmed to function with any subsequent programming
DO NOT EFFECT THE GATE
changes will slip ...
SL595 Manual - Page 29
... as operator line voltage 24V secondary 60VA.
2. BLACK 8 - OPEN J1-9 OBS. When using a remote control or Single Button Control Station in lieu of the radio block and mount the wire to...BK)
208/230V ONLY
(W)
4B3
5A 6
(W)
4A3
1B 2
(W)
2A1
115V MOTOR
CONNECTION
(PU) (SL595 RD) (BL)
(YE) (SL595 WH) (GY) SL595 GN)
42 8 5 13
(SEE NOTE 3) (BL/BK)
(BK)
115V BRAKE
(BK)
SOLENOID
...
SL595 Manual - Page 30
Terminal block in lieu of the soft open feature, perform the following modific ations to the operator:
• Remove the green wire from R4 of same type and rating. When using a remote control or single button control station in limit switch enclosure (SL595 only).
6. BRAKE SOLENOID
LOOP WIRING
(See NOTE 7) R4
TB1-5 TB2-CD
TB2-AB...
SL595 Manual - Page 31
...remote control or Single Button Control Station in lieu of the radio block and mount the wire to terminal block TB1 position 6. 2. Move the brown wire on Terminal Block TB1 position 6 (from R4 of the Soft Open... 24 VAC
J4 PLUG
DUAL
1
(WH)
GATE
2
(RD)
= TERMINAL BLOCK IN LIMIT SWITCH ENCLOSURE (SL595 ONLY).
(GY)
17
(BRN)
18
(GY)
19
(BRN) 20
INTERRUPT LOOP (SAFETY) EXIT LOOP
...
SL595 Manual - Page 32
... the same as the operator line voltage. Terminal block in lieu of the soft open feature, perform the following modifications to terminal block TB1 position 1.
32
40-32357J When using a remote control or single button control station in limit switch enclosure (SL595 only).
5. Fuse: 3AG, 3.2A, 120V, SLO-BLO SEE NOTE 5 EXTERNAL OVERLOAD
MOTOR
SEE...
SL595 Manual - Page 37
....
*Non stocked item. ELECTRICAL BOX
3
8 7
1
4
2
1
9
5 6
10
K1 (K72-34818)
SL585 Only
For SL595 Limit Box components, see pages 35 and 36. ITEM 1 2 3 4 5 6 7 8
9
10
INDIVIDUAL PARTS
PART # 13...25-2010
25-2015
25-2025
DESCRIPTION Limit nut Limit switch (SL585 only) Contactor Control board Stop switch Open/close switch Radio - 315 MHz Transformer - 120/208/230/460/60VA Transformer ...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 7 months ago)
Remote Control For Liftmaster /chamberlain 3850 Garage Door Opener
what is the correct remote control for the chamberlain/liftmaster 3850 garage door opener
what is the correct remote control for the chamberlain/liftmaster 3850 garage door opener
(Posted by sendtoalice 9 years ago)
How To Program Remote For Chamberlain Sl3000ul Garage Door Opener
(Posted by mhoPool 10 years ago)
How Do I Program Liftmaster Sl595 To Open And Close Using Keypad Entry?
is this possible? want a pin to open and close gate.. dont want pushbuttons or remote.
is this possible? want a pin to open and close gate.. dont want pushbuttons or remote.
(Posted by Bourked 11 years ago)
Program Remote Control On Mj 5011 Opener
How do you program the remote on the MJ 5011
How do you program the remote on the MJ 5011
(Posted by tjwilmore 11 years ago)