LiftMaster RSL12V Support Question
LiftMaster RSL12V Support Question
Find answers below for this question about LiftMaster RSL12V.Need a LiftMaster RSL12V manual? We have 4 online manuals for this item!
Question posted by parkermichael on September 27th, 2013
Where Is The Programming Button On My Liftmaster Rsl12v Sliding Gate?
I am trying to programm my liftmaster rsl12v sliding gate to open from the buttons in my car. Where is the progamming button on the liftmaster photo very helpful.
Current Answers
Answer #1: Posted by TechSupport101 on September 27th, 2013 9:45 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi, please refer to the video in the link provided below.
Thank you!
http://m.youtube.com/watch?v=456oha5TKxw&desktop_uri=%2Fwatch%3Fv%3D456oha5TKxw
Thank you!
http://m.youtube.com/watch?v=456oha5TKxw&desktop_uri=%2Fwatch%3Fv%3D456oha5TKxw
Related LiftMaster RSL12V Manual Pages
RSL12V Installation Manual - Page 1
... be limited until the battery is fully charged. UL325
compliant
UL991
compliant THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY.
RSL12V™ & RSL12VH™
VEHICULAR SLIDE GATE OPERATOR
INSTALLATION MANUAL
CSASOEEPALCCAAESSBORRILESE.
Visit www.liftmaster.com to locate a professional installing dealer in this manual.
STOP IMPORTANT NOTE: The...
RSL12V Installation Manual - Page 3
... single family units) hotel, garage, retail store or other building servicing the general public. RESIDENTIAL VEHICULAR GATE OPERATOR A vehicular gate operator (or system) intended for use in plain view on both the open and close directions of entrapment protection.
GATE OPERATOR ENTRAPMENT PROTECTION
UL325 Classification CLASS I CLASS II
Slide Gate Operator
Primary Type
Secondary Type...
RSL12V Installation Manual - Page 4
... features must be incorporated into every design. b. Activation of a vehicular horizontal slide gate. b. d. e. Specific safety features include:
• Gate Edges • Photoelectric Sensors • Vertical Posts
• Guards for vehicles. Swinging gates shall not open position. For a gate operator utilizing a non-contact sensor: a. c. One or more contact sensors shall...
RSL12V Installation Manual - Page 5
..., measured in the horizontal plane parallel to the designed fully open and
1.8 Gates shall be designed, constructed and installed such that covers in the open position.
4.1.1.2 Except for
shall be guarded or covered. horizontal slide gates:
4.1.1.1 The width of the gate where such stops shall horizontally or vertically project no more than is disconnected.
SAFETY...
RSL12V Installation Manual - Page 7
... 4 feet (1.2 m) high on the gate to prevent access through
openings anywhere the gate may be SERIOUSLY INJURED or KILLED by a qualified individual. • DO NOT install ANY wiring or attempt to service. • Disconnect power at the leading and trailing edges, and post mounted both inside and outside a horizontal slide gate. To prevent INJURY to...
RSL12V Installation Manual - Page 8
... battery compartment. Have a
qualified service person make repairs to gate hardware. • ALL maintenance MUST be performed by a LiftMaster professional. • Activate gate or door ONLY when it can increase the risk of FIRE or INJURY to the operator or in BOTH the open and close
gate cycles. After adjusting the force or the limit of...
RSL12V Installation Manual - Page 9
INTRODUCTION » OPERATOR SPECIFICATIONS + CARTON INVENTORY + HARDWARE INVENTORY
OPERATOR SPECIFICATIONS
This model is intended for use in vehicular slide gate applications:
Gate Classifications:
CLASS I & II
SIDE VIEW
REAR VIEW
Main Supply (Motor):
12 Vdc
Accessory Power:
12 V nominal Class II battery voltage source is limited to: • ...
RSL12V Installation Manual - Page 16
For proper functionality, the limits must be tested. The programming uses a combination of inactivity. The specific buttons used for a binding or sticking gate. • If one control (force or travel a minimum of 6 feet in the fully open position and the fully closed and the
chain is connected to start over:
1 Toggle the RESET switch on...
RSL12V Installation Manual - Page 17
...
3 GATE 1 Right Button DIAGNOSTIC
GATE 1
SET CLOSE
4 LEARN LIMITS Button
SET OPEN LIMIT
"BEEP"
SET CLOSE LIMIT
5 GATE 1 Left Button DIAGNOSTIC
6 LEARN LIMITS Button
SET OPEN LIMIT
GATE 1 SET CLOS
"BEEP"
ProInpseirdtye ProInpseirdtye
GATE 1
SET OPEN LIMIT
2
SET CLOSE LIMIT
LEARN LIMITS
GATE 2
LEARN LIMITS Button
PrOopuetsritdye
PrOopuetsritdye
IF THE LIMITS WILL NOT PROGRAM...
RSL12V Installation Manual - Page 18
...
3
GATE 1 Left Button
DIAGNOSTIC
4 LEARN LIMITS Button
SET OPEN LIMIT
GATE 1
SET CLOSE
"BEEP"
SET CLOSE LIMIT
ProInpseirdtye
5 GATE 1 Right Button DIAGNOSTIC
GATE 1
6 LEARN LIMITS Button
SET OPEN LIMIT
SET CLOSE
"BEEP" ProInpseirdtye
GATE 1
SET OPEN LIMIT
SET CLOSE LIMIT
LEARN LIMITS
GATE 2
2
LEARN LIMITS Button
PrOopuetsritdye
PrOopuetsritdye
IF THE LIMITS WILL NOT PROGRAM...
RSL12V Installation Manual - Page 25
... be opened and closed position, activation of the remote control button will open cycle another activation of the remote control will stop a moving gate during a normal open position...gate is reset, normal functions will operate as mud, rocks, dirt, etc. The next command given will blink in the open /close the gate.
E
REMOTE CONTROL Once the remote control has been programmed...
RSL12V Installation Manual - Page 27
...fuses are no obstruction the force adjustment is programmed with same type and rating. • Batteries are intact and not blown. Gate 2 has encountered an obstruction or the ...gate is connected between the COM and STOP input on either Gate 1 or 2, replace the control board. Replace blown fuses with self-diagnostic capabilities. Press the LEARN LIMITS button and press the GATE 2 buttons...
RSL12V Installation Manual - Page 28
...gate and verify that the Safety LEDs
(OPEN EDGE and CLOSE EDGE/PHOTO) are properly connected. Reprogram limits for SBC button...button to be connected for the operator to ensure they are OFF. Program the limits again. • Gate is properly grounded.
27 Disconnect the operator(s) and verify that the gate(s) slide...not connected. GATE DOES NOT FULLY OPEN OR CLOSE WHEN TRYING TO LEARN LIMITS...
RSL12V Installation Manual - Page 29
...open input is continuously activated. Verify connections
and operation for alignment and verify all the time. • The gate is started within the ratings for obstructions. • A fault has occurred. Use a remote control or the SINGLE BUTTON to program... ON A
COMMAND GATE RUNS TOO SLOW. Voltage should be above 11.5 Vdc. Verify that both directions. Slide the Lock/Bipart Delay switch...
RSL12V Installation Manual - Page 31
... to satisfy your authorized LiftMaster dealer for details. 3-BUTTON SECURITY✚® REMOTE CONTROL The 3-button remote control can detect an obstacle upon contact and stop the operator. Model K94-35225
SOLENOID GATE LOCK (LOW POWER) The automatic gate lock is a solenoid-driven lock that automatically unlocks when the gate is open the gate. Model 50-220
SENSING...
RSL12V User Manual - Page 1
Installation Date www.liftmaster.com
Please contact your authorized LiftMaster dealer for all of your service needs. USER'S GUIDE
VEHICULAR SLIDE/SWING GATE OPERATORS
RSL12V ™ & RSL12VH ™ RSW12V ™ & RSW12VH ™
Your model may look different than the model illustrated in this user's guide.
RSL12V User Manual - Page 2
... remote control will close the gate(s) manually, press the reset button. OPEN
OPERATION
RESET SWITCH/BUTTON The reset switch/button is located on both operators. Our operators are designed to meet or exceed UL325
safety standards and requirements and are quality manufactured for purchasing a LiftMaster gate operator. MODEL RSL12V SLIDE GATE OPERATOR Model RSL12V has a reset switch. On a dual...
RSL12V User Manual - Page 3
... switch/button to be reset:
The gate is in the open position, activation of the remote control button will not be toggled/pressed on the gate frame while the gate is moving. (Swing Only)
The gate is given.
REMOTE CONTROL Once the remote control has been programmed operator will operate as mud, rocks, dirt, etc. (Slide Only)
The gate has...
RSL12V User Manual - Page 5
...button to operate gate operator from outside by entering a 4-digit code on a specially designed keypad.
Model 50-220
SENSING EDGE (2-WIRE, NON-MONITORED) Sensing edges can be programmed to control the operator. Model G65ME120C5
OPEN....
3-BUTTON SECURITY✚® REMOTE CONTROL
OPEN
The 3-button remote control can be programmed to satisfy your authorized LiftMaster dealer ...
RSL12V Wiring Diagram Manual - Page 1
...J__
Alarm
Maglock w/Edernal Power Supply (Optional)
Coaxial Cable
Antenna
Gate 1 (Primary)
Motor
0
NC-6 00M-5 NO-4
C0NICA-32...as inside the house or garage.
• When the ... connected to ensure minimalcurrent drawandmaximum cycles. SLIDE RSL12V & RSL12VH
®WARNING
To protect against...
Open (Exit Loop)
e•m•g-__, Single Button (SBC)
g•m&#...
Similar Questions
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Alarm Going Off Almost Non-stop. Help!
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
Hello. I have an RSL12V unit for residential use. I went to open it the other day and the alarm trig...
(Posted by amcollectibles4 2 years ago)
Gate Wont Reset
turned gate to reset to allow several vehicles access. Now when turned back to NORMAL OPS it won't o...
turned gate to reset to allow several vehicles access. Now when turned back to NORMAL OPS it won't o...
(Posted by chizg 9 years ago)
How To Program Remote For Chamberlain Sl3000ul Garage Door Opener
(Posted by mhoPool 10 years ago)
Vehicular Gate Operator Rsl12v Not Opening
Will chirp but the gate does not move at all
Will chirp but the gate does not move at all
(Posted by Krcremodeling 10 years ago)