LiftMaster 3595 Support Question
LiftMaster 3595 Support Question
Find answers below for this question about LiftMaster 3595.Need a LiftMaster 3595 manual? We have 1 online manual for this item!
Question posted by tjmims on December 12th, 2012
Dog Chewed Through Sensor Wires, Wont Close On Own.
Hi,
My puppy decided it would be fun to chew through the sensor wires, as well as break one of the sensor brackets. Is there any way to disable the sensor?
Thank you.
Current Answers
Answer #1: Posted by GarageDoorMafiadotcom on December 15th, 2012 10:02 AM
GarageDoorMafiadotcom
Member since:
November 4th, 2012 Points: 25,600
Member since:
November 4th, 2012 Points: 25,600
There is no way to disable the safety sensor on your garage door opener.
Splice in a piece of bell wire, pay attention to the color code on the wires..
If you cant splice it, you need to replace the safety sensor.
GarageDoorMafia.com One stop online shop for all your garage door and opener needs.
Related LiftMaster 3595 Manual Pages
3595 Elite Series Manual - Page 1
...! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System® is connected and properly
aligned. ■ Periodic checks of your
opener.
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com
®
GARAGE DOOR OPENER Model 3595 3/4 HP
For Residential Use Install on the...
3595 Elite Series Manual - Page 2
... the door bracket 18
Connect the door arm to the trolley 19
Adjustment
20-22
Adjust the UP and DOWN travel limits 20
Adjust the force 21
Test the safety reversal system 22
Test the Protector System 22
Operation
23-26
Operation safety instructions 23
Using your garage door opener 23
Using the wall-mounted door control...
3595 Elite Series Manual - Page 3
... connected to garage door BEFORE installing and operating garage door opener to avoid malfunction and damage. Release the
door. To prevent damage to garage door and opener:
• ALWAYS disable locks BEFORE installing and operating the opener.
• ONLY operate garage door opener at 120V, 60 Hz to avoid entanglement. Carpenter's Level (Optional)
12
Tape Measure
Pencil Wire Cutters
Drill...
3595 Elite Series Manual - Page 4
... garage door is required. Vertical Centerline of Garage Door
Safety Reversing Sensor
Safety
Gap between the bottom of door
Reversing Sensor
must not exceed 1/4" (6 mm)
Access Door
Wallmounted Door Control
4 You may not work properly.
• The floor or the garage door MUST be required. Header Wall
FINISHED CEILING
Support bracket & fastening hardware is closed. Otherwise...
3595 Elite Series Manual - Page 5
...Bracket
Header Bracket
Chain
Motor Unit With Light Lenses Chain Spreader
Door Bracket
Rail 2 Conductor Bell Wire White & White/Red
Chain Pulley Bracket
Trolley
Safety Sensor Bracket (2)
Curved Door Arm Section
The Protector System® (2) Safety Reversing Sensors...Straight Door Arm Section Carton Inventory
Your garage door opener is packaged in the foam. contain the motor unit and...
3595 Elite Series Manual - Page 6
... Bolts 1/4"-20x5/8" w/Lock Washers
Washered Bolt
Screw #8-32x3/8"
5/16"-18x1/2"
Chassis Support Bracket
Washered Bolt 5/16"-18x1/2"
Opener Back Flange
Opener Side Flange
6 ASSEMBLY STEP 1
Attach the Rail to the Motor Unit
To avoid installation difficulties, do not run the garage door opener until instructed to do so.
• Remove the bolt and lock nut from...
3595 Elite Series Manual - Page 7
... tight. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCTIONS.
2. Install garage door opener 7 feet (2.13 m) or more above floor.
7. Sprocket noise can result if chain is normal.
Disable ALL locks and remove ALL ropes connected to garage door BEFORE installing opener to the position shown when the door is approximately 1/2" (13 mm) above the base of the rail...
3595 Elite Series Manual - Page 12
... seen clearly, is recommended to each garage door opener. NOTE: The functional temperature range of door control on the motor unit: white to white and white/red to 24 VOLT low voltage wires.
Do NOT pierce wire with care to secure wire in sight until the sensor beam is not connected BEFORE installing door
control. • Connect ONLY to...
3595 Elite Series Manual - Page 13
... and downward until the lens hinge is in an open door falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless garage doorway is connected. Then the lights will turn OFF.
• Reverse the procedure to close the lens.
• Use A19, standard neck garage door opener bulbs for approximately 4-1/2 minutes when power is clear...
3595 Elite Series Manual - Page 14
... wiring connection.
• Garage door installation and wiring MUST be grounded.
• Reinstall the cover. the white (neutral) wire to the following procedure. To avoid installation difficulties, do not run the opener at this time. INSTALLATION STEP 9
Electrical Requirements
To avoid installation difficulties, do not run the opener at this time.
The opener must be in ANY way...
3595 Elite Series Manual - Page 15
... installed on the wall, the brackets must be securely fastened to clip onto the track of sectional garage doors without additional hardware. To prevent SERIOUS INJURY or DEATH from a closing .
INSTALLATION STEP 10
Install The Protector System®
The safety reversing sensor must be connected and aligned correctly before the garage door opener will detect an obstacle in...
3595 Elite Series Manual - Page 20
...8226; Does the door stay closed and not reverse unintentionally when fully closed position:
Decrease down travel .
Door MUST reverse on contact with the door's upward travel . Turn the UP limit adjustment screw clockwise.
Limit Adjustment Screws
ADJUSTMENT LABEL
• If the door reverses when closing garage door.
• Incorrect adjustment of the opener during adjustment procedures...
3595 Elite Series Manual - Page 21
... control may be tested.
Reversal halfway through down travel , it will reverse. The door should reverse. After each adjustment, run the opener through a complete travel cycle.
• If the door doesn't open at least 5 feet (1.5 m), INCREASE UP (open) force by a closing garage door.
• Too much force on a 1-1/2" (3.8 cm) obstruction. The maximum force adjustment range is...
3595 Elite Series Manual - Page 22
... springs and hardware). • Any repair to or buckling of the garage floor. • Any repair to or adjustment of the door.
• Press the remote control push button to close from a remote if the indicator light in the down position. The garage door opener will flash. Without a properly installed safety reversal system, persons (particularly small...
3595 Elite Series Manual - Page 23
...-set to pull garage door open door falling rapidly and/or unexpectedly.
7. If you purchase a new remote, or if you release them until completely closed. Activate your opener with the safety reversing sensor correctly installed and aligned): 1. See Programming. When the opener is A19. If open, the door will open garage door. If closed . If closing , the door will reverse. 3. If...
3595 Elite Series Manual - Page 26
If rope knot becomes untied, you disabled all remotes.
4. To reconnect the door to the limit
and force adjustments. Emergency ... broken wire.
• Are the wiring connections correct? Adjust if
necessary (See page 7). The opener does
not require additional lubrication. If it is CLOSED. Remove any restriction.
• The garage door spring may be frozen to the ground. Opener operates ...
3595 Elite Series Manual - Page 27
... to force or travel limits. Repeat safety reverse test after any point of door arm length, close :
• If the opener lights blink, check the safety reversing sensor. Weather conditions in any adjustment of travel limits adjustment procedures on ? The garage door opens and closes by its springs. If it off :
• Is the Light feature on page...
3595 Elite Series Manual - Page 29
...heard.
Press the Prog button again to circumvent that technical measure.
Your garage door opener has already been programmed at the factory to operate your hand-held ...garage door opener does not authorize the purchaser or supplier of the garage door opener, which provides security against code-theft devices, will open and close when you wish to operate your garage door opener...
3595 Elite Series Manual - Page 30
...button.
2. The keypad will be programmed to confirm Learn Mode. Press the four buttons for your garage door opener. Press the temporary 4-digit PIN you have chosen, then press Enter. Press and release the "...and will work , press the number of hours (up one button close feature has been activated. The opener light will blink once when the temporary PIN has been learned. Release ...
3595 Elite Series Manual - Page 33
...: The Garage Door Opener Surge Protector is designed to a programmable number of hours or entries.
371LM 373W 915LM
41A5281
Extension Brackets:
CLOSED
(Optional) For safety reversing sensor
OPEN
installation onto the wall or floor.
78LM
LOCK
LIGHT
Multi-Function Door Control Panel:
Provides a lock feature which prevents operation of your garage door is open garage door manually from...
Similar Questions
I Have Installed A Chamberlan Garage Door Opener And The Remote I Was Using Is
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
I have been using a Chamberlan garage door opener and its remote has been defective since of late.Pl...
(Posted by donweera42 8 months ago)
Wiring Motor For 3595s
3 wires come out of motor: red, white, blue. Capacitor has a yellow and purple wire coming from circ...
3 wires come out of motor: red, white, blue. Capacitor has a yellow and purple wire coming from circ...
(Posted by Bobbaxter6 8 months ago)
Garage Door Opens After Shutting.
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
My Lift master 8550 inside keypad is Inside wall pad is model #880LM. outside keypad Model # is 877M...
(Posted by BONNIECA92 2 years ago)
Need To Push 3 Times To Close Door. It Lurches Once Or Twice Then Closes.
(Posted by guarigliac 10 years ago)
Opener Light Turns On By Itself
Hi, I have a LiftMaster 3595 and I would enter the garage from time to time and notice that the lig...
Hi, I have a LiftMaster 3595 and I would enter the garage from time to time and notice that the lig...
(Posted by michael47837 12 years ago)