Kyocera FS 1128 Support Question
Kyocera FS 1128 Support Question
Find answers below for this question about Kyocera FS 1128 - MFP.Need a Kyocera FS 1128 manual? We have 1 online manual for this item!
Question posted by jackvgarrison on March 22nd, 2011
Kyocera Fs-1128mfp Scan Error Message 1102.
When I try to send a document through the scanner to a folder on my server it will run the doc through the scanner then give me error 1102. Error type : Setting
Current Answers
Related Kyocera FS 1128 Manual Pages
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 2
...; Connecting Modular Cords Operation at the machine panel • Selecting Language • Date and Time Settings • Setting Network Interface Parameters Operation at the PC • Accessing COMMAND CENTER (Internal HTML web page) • Sharing Folder to use Scan to use this guide.
2 Installation of Microsoft Corporation in this machine. The designations ™ and...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 3
... a stable position.
Unpacking
1 Unpack the machine and all its included components. SETUP GUIDE
3
Prolonged use
without sufficient clearance may cause overheating. If the machine is FS-1128MFP, the modular cord with the attached ferrite core is enclosed. When carrying the printer, always hold the right and left sides as shown.
2 Remove the...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 4
...
1 Open the front cover.
Guide Case
2 Check the lock lever to the machine right as required. Shipping Lock
IMPORTANT: When installing the Document Processor, refer to Installation Guide attached to the Document Processor.
4 Attach the Guide Case to the UNLOCK position.
4
SETUP GUIDE
Preparations
3 Slide the Shipping Lock to the unlock position.
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 7
Preparations
Connecting Cables
1 Turn the power switch off (O).
2 Connect the machine to the PC or your network device.
SETUP GUIDE
7 These cables are sold separately. When using the network interface, remove the cap. Otherwise, it may cause paper jams.
6 Push the cassette securely ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 8
... The machine will appear on (|). this will take approximately 15 minutes. Connecting Modular Cords (FS-1128MFP only)
1 Turn the power switch off (O).
2 Be sure to warm up.
Preparations
Available Standard Interfaces:
Interface
Function
Necessary Cable
Network Interface
Printer/Scanner/ LAN (10Base-T or 100Base-TX, Shielded) Network FAX
USB Interface
Printer/TWAIN/ USB2.0 compatible...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 9
...; SETUP GUIDE
9 3 Connect the modular cord with the attached
ferrite core to the line jack (A) of the machine.
Preparations
5 Turn the power switch on the message display.
Replacing the Operation Panel Language Sheet
1 Remove the attachements as shown in the figure. B
4 Route the cords as shown. Once the toner has been...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 11
... Setup
[Left Select] Key [Right Select] Key
Numeric Keys [Back] Key
Selecting Language
Perform the following procedure to select the time zone.
1 In the Common Settings menu, press U or V to select Common Settings. 4 Press [OK]. The default message language is set and the Common Settings menu reappears. The Sys.
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 12
... Time. 2 Press [OK]. The date and time is valid only in the message display and adjust
as necessary to match the current time.
1 In the Date Setting menu, press U or V to set and the Date Setting menu reappears.
12
SETUP GUIDE Summer Time Setting
Perform the following procedure to select Date/Time. 2 Press [OK].
The...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 13
... Off and On again. TCP/IP (Enable/Disable TCP/IP)
This selects the settings for your PC and your network administrator when selecting the network setting. IPv4 Settings (TCP/IP IPv4 settings)
This selects the settings for Internet Protocol.
Panel Setup
Setting Network Interface Parameters
This machine supports TCP/IP and TCP/IP (IPv6) protocols.
screen...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 14
..., press U or V to select DHCP. 2 Press [OK]. Panel Setup 14
• DHCP (DHCP setting) • Bonjour (Bonjour setting) • IP Address (IP address setting) • Subnet Mask (Subnet mask setting) • Default Gateway (Gateway setting)
DHCP
1 In the IPv4 Setting menu, press U or V to select Subnet Mask. 2 Press [OK].
Use Y and Z to increase or decrease, respectively...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 15
... is enabled. 4 Press [OK]. The Sys.
SETUP GUIDE
15
The TCP/IP(IPv6) screen appears. 3 Press U or V to select Network Setting. 5 Press [OK]. You can set and the IPv6 Setting menu reappears.
Menu/Count. The System screen appears. 4 Press U or V to select whether TCP/IP (IPv6) is a communications protocol used primarily on Macintosh...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 16
Panel Setup
6 Press U or V to select whether AppleTalk is set and the Network Setting menu reappears.
16
SETUP GUIDE The AppleTalk screen appears. 8 Press U or V to select AppleTalk. 7 Press [OK]. The AppleTalk is enabled. 9 Press [OK].
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 18
...scan data to e-mail for transmission. The scanner system network component offers e-mail function. Select On to use RA to configure IPv6 addresses.
Specifies the IPv6 prefix length of the hosts or network with which it can connect to a mail server...GUIDE
The format of the automatic configuration made under RA (router setting).
3 Click Submit.
Assigns an IPv6 address to enable the ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 20
...folder should be entered correctly for SMTP authentication. The table below provides a summary of the
items displayed on each field.
Enter the domain names that can be permitted or rejected. Enabling SMB Function
Stores the image data of scanned... within Windows on that PC.
1 Click Scanner -> SMB. 2 Enter the correct settings in each server and register them to this machine.
•...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 21
... • Shares the FTP server
Login username and Login password are encrypted using the one algorithms at the FTP server.
1 Click Scanner -> FTP. 2 Enter the correct settings in COMMAND CENTER.
The table... the data of the following information on the scanner FTP page.
Set the FTP Port Number or use more than one of originals scanned on this machine.
• Login user name...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 23
... section explains how to send data to receive data in the destination computer.
The following example explains how to create a folder named "scannerdata" on a normal folder. IMPORTANT: Log on to Windows with the destination computer to receive data. 4 Sharing PC Folder
Sharing PC Folder
To use Scan to SMB (PC) function, a "shared folder" must be connected to...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 30
...you want fonts installed on your computer in this driver software
anyway.
5 A message appears saying that the printer has been installed successfully. Installing Printer Driver in Macintosh...10.3
Only or OS X 10.4 or higher depending on the CD-ROM. For details, refer to Device Settings in the printer driver operation manual on your computer to be replaced, select Custom Mode and deselect the...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 31
... used to the operating system. SETUP GUIDE
31
Next, specify the print settings. In addition to Easy Install, the Installation Type options include Custom Install, which allows you to specify the components to add the installed printer driver. 5 Double-click Kyocera OS X vx.x.
If an IP or AppleTalk connection is automatically recognized and...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 32
...
Register this machine to the TWAIN Driver.
1 Select Start button of the Windows display, All Programs, Kyocera and then TWAIN Driver Setting.
32
SETUP GUIDE This completes the printer setup procedure. Installing Printer Driver
10 Click the IP icon for an IP connection or the AppleTalk icon ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 33
..., enter Login User Name (up to 64 characters) and Password (up to the Model field and select this machine from the list. 5 Click User Authentication Settings. SETUP GUIDE
33 Installing Printer Driver
NOTE: You can also add the machine to a PC when selecting Start of the Windows
display, Control Panel and...
Similar Questions
How To Set Up An Address Book Fs-1128mfp Scan To Folder
(Posted by mbuPl 9 years ago)
Send Error Message: 1102 Check Smb Settings.
(Posted by jacquesniyibizi 11 years ago)
When I Am Trying To Send An Email Via Scanner, I Recieve An Error Type: Setting.
I am trying to scan documents and send them via email from Kyocera FS 1128. I just recently connecte...
I am trying to scan documents and send them via email from Kyocera FS 1128. I just recently connecte...
(Posted by swingleriphone 11 years ago)
