Kyocera FS 1128 Support Question
Kyocera FS 1128 Support Question
Find answers below for this question about Kyocera FS 1128 - MFP.Need a Kyocera FS 1128 manual? We have 1 online manual for this item!
Question posted by jean on July 8th, 2010
Fs-1028mfp Fs-1128mfpFailure C3100
On a new machine installed by myself, on powerin up I get the message :Machine failure / Call service / C3100
Current Answers
Related Kyocera FS 1128 Manual Pages
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 2
... designations ™ and ® will not be used in the U.S.A. Introduction
About this Guide
This guide explains the following setting method necessary to SMB • Installing Printer Driver • Setting TWAIN Driver • Setting WIA Driver
IMPORTANT: Please read safety information on the Operation Guide before installing this machine. Installation of their respective companies.
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 3
... / 220 to 240 V AC, 50/60 Hz
CAUTION: Be sure to provide enough space around machine. IMPORTANT: Place the machine in a stable position. SETUP GUIDE
3 Prolonged use
without sufficient clearance may cause overheating.
If the machine is FS-1128MFP, the modular cord with the attached ferrite core is enclosed.
When carrying the printer, always...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 4
... Container
1 Open the front cover. Shipping Lock
IMPORTANT: When installing the Document Processor, refer to Installation Guide attached to the Document Processor.
4 Attach the Guide Case to the UNLOCK position.
4
SETUP GUIDE
Guide Case
2 Check the lock lever to the machine right as required. Preparations
3 Slide the Shipping Lock to the unlock position...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 6
... buttons and sliding the guides to fit the width of the paper. Preparations
Loading Paper
1 Carefully pull the cassette all the way out of the machine and remove the protective packing from inside the cassette.
2 Adjust the paper length by pressing in the cassette, with side to fit the size of...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 7
These cables are sold separately. Otherwise, it may cause paper jams.
6 Push the cassette securely all the way back into the machine until it stops. IMPORTANT: Do not exceed the upper limit of the cassette. When using the network interface, remove the cap. SETUP GUIDE
7 Preparations
Connecting ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 8
... outlet.
4 Turn the power switch on the message display. The machine will take approximately 15 minutes. Once the toner has been replenished, Ready to copy will appear on (|).
The machine begins to loop the cord three times through the ferrite core.
8
SETUP GUIDE Connecting Modular Cords (FS-1128MFP only)
1 Turn the power switch off...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 9
... modular cord with the attached
ferrite core to
A
the telephone jack (B) of the machine. The machine begins to copy will appear on (|).
B
4 Route the cords as shown. this will begin replenishing the toner;
If the mache is first installation, it will take approximately 15 minutes. Once the toner has been replenished, Ready to...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 11
... Settings screen appears. 5 Press U or V to select Common Settings. 4 Press [OK]. SETUP GUIDE
11 The default message language is set and the Common Settings menu reappears. The Language screen appears showing the list of the message display. Date and Time Settings
Setting the Time Zone
Perform the following procedure to select the...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 12
... is enabled. 4 Press [OK]. The Summer Time screen appears. 3 Press U or V to select Date/Time. 2 Press [OK].
The date and time is shown in the message display and adjust
as necessary to match the current time.
1 In the Date Setting menu, press U or V to select whether summer time is set and...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 13
...U or V to select TCP/IP. 10 Press [OK]. Panel Setup
Setting Network Interface Parameters
This machine supports TCP/IP and TCP/IP (IPv6) protocols. IP is enabled. 12 Press [OK]. TCP...Setting menu screen appears. After all network related settings have been done, turn the machine Off and On again.
This machine routinely uses the TCP/IP (IPv4) protocol, but provides a separate setting for ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 17
..., and 100BASE-TX-Full. The web page displays basic information about the machine and COMMAND CENTER as well as the WSD device name. Network Settings
This page allows you to security, network printing, e-... refers to the internal HTML web page that is installed in the machine from which you can verify the operating status of the machine and make settings related to make the settings that category...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 18
...print system is recommended that starts with which it is an embedded protocol to support this machine can connect to a mail server.
Select On to use RA to obtain IPv6 IP addresses... Settings
The following environments:
• It must have manually assigned an IP address that the machine be used in an environment in which this function. Use COMMAND CENTER, to an e-mail server...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 19
...will be authenticated in each field. Set the SMTP Port Number or use e-mail, this machine tries to connect to the POP3 server.
If you want to the SMTP server when set.... The SMTP authentication supports Microsoft Exchange 2000.
Sets the timeout in seconds during which this machine tries to connect to the SMTP server.
Enter the timeout in seconds during which this protocol...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 20
... parameters in COMMAND CENTER. The table below provides a summary of the e-mail body. Note that no mail message can also specify the e-mail addresses.
3 Click Submit. It is stored.
User access rights for the machine to the necessary folder should be entered correctly for SMTP authentication.
The sender address must consult the...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 21
... Scanner -> FTP. 2 Enter the correct settings in COMMAND CENTER. In order to access a FTP server, you to specify the encryption algorithm for the machine needs to be installed and administrated at a time. (This is possible by turning FTP Encrypted TX to an FTP server.
The FTP user account for data communication. Item...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 22
...add.
The members must be added to add, edit or delete Contacts or Groups. Adding a New Contact
1 Open the Address Book Contacts page. 2 Click Add Contact. You can continue editing ... FAX number
and i-FAX even if the FAX System is not installed.
4 Click Submit. Accessing COMMAND CENTER
Editing Address Book
This machine has an address book function. Check the members you want
to...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 23
... C.
IMPORTANT: To use for Windows Vista)
If the destination of files is a Windows Vista-based computer, you want use Scan to SMB (PC) function, the machine must be set up with administrator privileges.
1 On the Windows Firewall Settings dialog box, click the Exceptions tab.
4 Sharing PC Folder
Sharing PC Folder
To...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 28
... Driver in and connected to the Found New Hardware Wizard dialog box displays, select Cancel.
2 Insert the CD-ROM supplied with administrator privileges.
Express Mode automatically detects connected machines and installs the required software. Use Custom Mode if you how to connect your machine to install the software.
ROM window in Windows Explorer and double...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 29
... your connection type.
• Express Mode • Custom Mode
Express Mode
In Express Mode, the installer automatically detects the machine when it is connected via a USB.
4 A window appears in applications.
SETUP GUIDE
29 This will be installed and click Next.
3 You can check the settings.
Specify whether to the correct procedure for standard...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 30
... higher depending on your computer in this driver software
anyway.
5 A message appears saying that the printer has been installed successfully. For details, refer to be replaced, select Custom Mode and deselect ... in the install wizard window, select the software packages to be installed and the specify the port, etc. For example, if you exit the installation. If the device setup dialog box...
Similar Questions
Kyocera Fs-1128mfp/ Ecosys Gives Machine Failure With Code C3100
When machine powered the scanner moves to the lower side but it doesnot come back and the scanner li...
When machine powered the scanner moves to the lower side but it doesnot come back and the scanner li...
(Posted by mawandajoseph 10 years ago)
Kyocera Fs 1128
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
(Posted by spaffordb 11 years ago)