Kyocera FS 1128 Support Question
Kyocera FS 1128 Support Question
Find answers below for this question about Kyocera FS 1128 - MFP.Need a Kyocera FS 1128 manual? We have 1 online manual for this item!
Question posted by kelleyspanos on December 17th, 2010
How Do I Print The Contacts In The Address Book?
I can't find a place where I can print the contacts I have entered in my address book.
Current Answers
Related Kyocera FS 1128 Manual Pages
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 3
IMPORTANT: Place the machine in a stable position.
SETUP GUIDE
3 Prolonged use
without sufficient clearance may cause overheating. When carrying the printer, always hold the right and left sides as shown.
2 Remove the packing tape and the protective sheet. If the machine is FS-1128MFP, the modular cord with the attached ferrite core is...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 5
Preparations
6 Push the lock lever back into place. 3 Shake the toner container horizontally 5 or 6 times so that the toner inside becomes evenly distributed.
4 Remove the orange protective seal.
5 Push on the PUSH marks on the toner container until the container clicks into its LOCK position (away from you).
7 Close the front cover.
SETUP GUIDE
5
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 6
... size of the paper.
4 Fan the paper, then tap it on a level surface to avoid media jams or skewed printing.
5 Place the paper in on the release buttons and sliding the guides to be printed downward, so that the leading edge is aligned against the paper stopper.
6
SETUP GUIDE Preparations
Loading Paper
1 Carefully...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 7
.... When using the network interface, remove the cap. Preparations
Connecting Cables
1 Turn the power switch off (O).
2 Connect the machine to the PC or your network device.
These cables are sold separately.
IMPORTANT: Do not exceed the upper limit of the cassette. SETUP GUIDE
7
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 8
this will begin replenishing the toner;
Connecting Modular Cords (FS-1128MFP only)
1 Turn the power switch off (O).
2 Be sure to warm up. Preparations
Available Standard Interfaces:
Interface
Function
Necessary Cable
Network Interface
Printer/Scanner/ LAN (...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 14
...menu reappears. Use Y and Z to select Bonjour. 2 Press [OK]. The IP address is set and the IPv4 Setting menu reappears.
Press U and V to select whether DHCP is ... mask.
Panel Setup 14
• DHCP (DHCP setting) • Bonjour (Bonjour setting) • IP Address (IP address setting) • Subnet Mask (Subnet mask setting) • Default Gateway (Gateway setting)
DHCP
1 In ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 17
... highly recommended. You must restart this machine after you to make settings related to security, network printing, e-mail transmission and advanced networking.
1 Run the web browser. 2 In Address or Location, enter the machine IP address as the WSD device name.
SETUP GUIDE
17 Network Settings
This page allows you have completed these settings in order...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 18
...:
• It must be a times where transmission is turned On, the IP addresses and server information are obtained via DHCPv6 based on the printing system network component.
Assigns an IPv6 address to obtain IPv6 IP addresses by automatic configuration. Specifies the IPv6 address of the hosts or network with a number between 192 and 223, it...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 19
...
POP before SMTP as , the account name set here will be used for E-mail size is selected for Authenticate as the protocol.
Enter the SMTP server name or its IP address.
Sets the timeout in each field. The SMTP authentication supports Microsoft Exchange 2000. When Other is disabled.
When Other is selected...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 20
... Windows User logon on the scanner SMB page.
Accessing COMMAND CENTER
Item Sender Address
Signature Domain Restriction
Description
Enter the E-mail address of the person responsible for the printing system, such as a file in a desired folder on that PC.
1 Click Scanner -> SMB. 2 Enter the correct settings in COMMAND CENTER.
The signature is stored. It is...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 21
....
When turned On, data communications are encrypted using operation panel) • Host name or IP address of FTP server • Port number (normally 21) • Path (path from the home ... • Password (using the one algorithms at the FTP server.
1 Click Scanner -> FTP. 2 Enter the correct settings in COMMAND CENTER.
SETUP GUIDE
21 In order to access a FTP server, you to ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 22
... a FAX number
and i-FAX even if the FAX System is not installed.
4 Click Submit. Accessing COMMAND CENTER
Editing Address Book
This machine has an address book function.
Adding a New Contact
1 Open the Address Book Contacts page. 2 Click Add Contact.
Add page opens. 3 Enter the number and name of PC folder (SMB), FTP server's path, FAX, and i-FAX number are registered...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 26
... use alphabets, numerals, and symbols (ASCII codes from 0 × 20
to 0 × 7F) only to enter Path. In the Search Companion, click Printers, Computers, or people, and then click A computer on the network.... search results.
5 Double-click the "scannerdata" folder and check the full path displayed in the Address Bar. In this case, the entry for Path is sent.
1 Click Search in the shared folder...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 29
...window. Installing Printer Driver
4 Click Install Software. Then return to share the print system name or set the print system as an existing machine and then click Next. The software install wizard ...installed and click Next.
3 You can check the settings.
It does not appear if the print system is turned on your version of Windows and your connection type.
• Express Mode &#...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 30
... A message appears saying that the printer has been installed successfully. For details, refer to Device Settings in the printer driver operation manual on your Mac OS version.
30
SETUP GUIDE
Click...the software to be replaced, select Custom Mode and deselect the Fonts checkbox in the print system.
You can specify the settings for items such as optional features installed in the...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 31
IMPORTANT: In the Authenticate screen, enter the name and password used , the settings below are required. Next, specify the print settings.
If an IP or AppleTalk connection is automatically recognized and connected.
8 Open System Preferences and click Print & Fax.
9 Click the plus symbol (+) to be installed.
This completes the printer driver installation. SETUP GUIDE...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 32
Installing Printer Driver
10 Click the IP icon for an IP connection or the AppleTalk icon for an AppleTalk connection and then enter the IP address and printer name.
11 Select the installed printer driver and click Add.
12 Select the options available for the machine and click Continue.
13 The ...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 34
... Scanner List field. Continue installation.
34
SETUP GUIDE
Installing Printer Driver
8 The machine is not necessary to register when using the machine
possesses an IP address or host name that you have provided. NOTE: The following is registered to the WIA Driver. Click Edit to delete the added machine. NOTE: Click...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 35
... to the PC.
The machine is unknown, contact Administrator.
4 Select the checkbox beside Authentication, enter Login User Name (up to 64 characters) and Password (up to 64 characters) and then click OK.
5 Click Close. SETUP GUIDE
35 Installing Printer Driver
NOTE: When the machine's IP address is registered to Step 5. 3 Click the Settings...
FS-1028MFP/1128MFP Setup Guide Rev-1 - Page 36
Rev.1 2010.1 Printed in China 302H956021
Similar Questions
Kyocera Fs 1128
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
How do you print to cassette 2 in kyocera FS 1128 without pushing a button?
(Posted by spaffordb 11 years ago)