KitchenAid KUDC10FXSS Support Question
KitchenAid KUDC10FXSS Support Question
Find answers below for this question about KitchenAid KUDC10FXSS.Need a KitchenAid KUDC10FXSS manual? We have 4 online manuals for this item!
Question posted by achdcpc on September 25th, 2012
Do I Need An Air Gap For My Kudc10fxss Dishwasher.
We are in Sunnyvale California. Not sure if there is speicifc code that would require an air gap to be installed for the dishwasher
Current Answers
Related KitchenAid KUDC10FXSS Manual Pages
Dimension Guide - Page 1
... codes and ordinances. Make sure to connect the drain hose to house plumbing lower than 20"
Use ¹⁄₂" (1.3 cm) minimum I.D. Make sure to improve
Dimensions are for use an air gap if the drain hose is resistant to the dishwasher opening.
If required, the air gap should be compressed. (not used on one end.
Insulation may be installed...
Installation Guide - Page 2
... or seriously injured if you don't follow instructions.
The dishwasher must be performed by a qualified service technician.
You Need to meet all electrical and plumbing national and local codes and ordinances.
2 WARNING
You can result in this dishwasher as specified in these instructions.
• Installation should be installed to :
• Slowly open door. Do not push...
Installation Guide - Page 3
... line
See "Electrical Requirements" section.
Additional parts supplied with
dishwasher
MSailkveersuGrreeaelnl these parts are included in dishwasher
Other useful items you may need :
(3.81-5 cm... Other parts you may also need :
Flashlight
Bath towel
Supplied in plumbing supply stores. All Installations Tools needed :
Copp O.D. Check local codes. For Direct Wire: use ...
Installation Guide - Page 4
... or electrical wiring where they can interfere with floor at the end of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to freezing, have it may be installed must provide clearance between the side of the dishwasher door and the wall or cabinet.
• square opening ). Damage from your dealer for...
Installation Guide - Page 6
... can be verified by a licensed plumber.
• 120°F (49°C) water at dishwasher O.D.
copper tubing with your home and local codes and ordinances.
• Use a UL Listed/CSA Approved strain relief. drain line fittings. • If required, the air gap, should be installed in house plumbing and 20" (50.8 cm) minimum above the floor. Drain...
Installation Guide - Page 10
... hammer and screwdriver, knock plug into position. Attach drain hose to waste tee and cut if needed , drill a 1¹⁄₂" (3.8 cm) diameter hole in cabinet wall or side of...into disposer. no air gap • Option B, No waste disposer -
This will be installed. Helpful Tip: To reduce vibration of the hose, keep the hose away from moving when dishwasher is required.
1 Drill ...
Installation Guide - Page 11
...
1. If the drain hose
was cut ribbed section.)
4. Make sure the area under a wood countertop)
Moisture barrier
1. Use needle-nose pliers to move and install dishwasher. Attach drain hose to air gap and cut if needed . (Do not cut , use dishwasher until completely installed. Install Moisture Barrier (under a wood countertop)
Install moisture barrier (under the cabinet is clean and dry...
Installation Guide - Page 13
...Gently tug on wires to be installed (you will be sure both are tucked inside terminal box...needed , see website for animated representation of countertop to follow these instructions can result in terminal box. Connect ground wire
Tighten strain relief screws to white, using UL Listed/CSA Approved twist-on strain relief
Electrical Shock Hazard Electrically ground dishwasher. Make sure...
Installation Guide - Page 14
... the setscrews facing down. Install the Door Handle (on mounting studs with Installation Instructions. Tighten the setscrews ¹⁄₄ turn past snug. add shims as needed in use. Not recommended for example, the kitchen floor tile does not extend into the cabinet opening , but the dishwasher will allow the dishwasher to 34" (86.4 cm...
Installation Guide - Page 15
...keep from drilling through panel. Stand dishwasher upright
2 Attach handle
6" (15.2 mm)
Install the custom hardware handle(s) on the wooden panel using a drill bit. Make sure that a cabinetmaker cut the customer... for the screws heads to be made to the front of the precise dimensions needed. If the installation needs a higher toe kick, adjust the height of the wooden panel.
4 Predrill ...
Installation Guide - Page 18
... close the door a few times. Helpful Tip: Temporarily tape utilities to the floor in the front leg of dishwasher. If the door closes or falls open under its own weight, the door tension will need to rear leg. Using a nut driver or hex socket, remove the screw from the rear leg of...
Installation Guide - Page 19
...sure rubber washer is level. With some installations, it may be required to seal the rubber gasket. Preferred method
Optional method
IMPORTANT: If wheels were removed, cover the floor when moving the dishwasher. Slowly move dishwasher...;₄" fitting up or down until dishwasher is centered from front to the coupling can result.
19
If needed
Place level against the front panel. ...
Installation Guide - Page 20
Turn on wire connectors (not included) rated to connect your household wiring to 16-gauge dishwasher wiring.
If needed , see website for animated representation of this step. Visit www.kitchenaid.com/drain under FAQ tab. Pull cable through UL Listed/CSA Approved strain relief ...
Installation Guide - Page 21
WARNING
Electrical Shock Hazard Electrically ground dishwasher. Make sure wires are secured. Visit www.kitchenaid.com/electrical under the washer.
Connect ground wire to be sure both are tucked inside terminal box. Gently tug on UL...
ground wire
Terminal box wire: white black ground connector
If needed, see website for animated representation of cover. Place wires inside box.
Installation Guide - Page 23
... position. Reinstall the lower dish rack. If needed, see website for animated representation of the dishwasher, making sure not to push or pull any wires or hoses. (Do not force.) Side panels will need to cut a slit in the pad to avoid splitting the wood before installing screws. Visit www.kitchenaid.com/anchoring under FAQ...
Use & Care Guide - Page 1
... owning a KitchenAid® product. These instructions include a "Troubleshooting" section to follow User Instruction Book. Have your KitchenAid dishwasher, please contact us that you have provided an easy to help you through any problems you need further assistance using your complete model and serial number ready. In Canada: visit www.kitchenaid.ca or...
Use & Care Guide - Page 5
... and energy.
If the door is located on the left-hand side of the dishwasher can lead to determine the amount of detergent needed based on the bottom of the tub after the cycle is inside of the dishwasher.
Heavy Duty cycle for tough soil cleaning
The Heavy Duty cycle is essential. Place...
Use & Care Guide - Page 6
...automatic
A
dishwasher detergent
results in the image above. Spray cannot reach nested items.
Upper rack
Lower rack
■ Make sure nothing keeps...Water
C
PRE- MAIN WASH
WASH
A. Heavily soiled loads require more detergent. If you use too much soil remains on...with soiled surfaces facing down to the level shown, if needed.
6 Fill the Pre-Wash section to avoid nesting....
Use & Care Guide - Page 13
...needed for up to call . DETERGENT REMAINS IN THE DISPENSER OR TABLET IS ON BOTTOM OF TUB
Check for the winter
Clean the drain air gap periodically to ensure proper drainage of the rack for the dishwasher to the dishwasher...sure you will encounter cycles that is left in dishwasher and the home drain system.
Check the drain air gap... Air Gap
Some state or local plumbing codes require ...
Use & Care Guide - Page 16
...DISHWASHER WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, KitchenAid brand of original purchase date is required...God, improper installation, installation not in accordance
with electrical or plumbing codes, or use...appliance light bulbs, air filters or water ...
KitchenAid Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Water supply hookup - Built-in refrigerator
...water line with the pipe clamp. Make sure the outlet end is needed in the reverse-osmosis system is a cold.../French door refrigerators Changing/replacing the water filter - Install tubing only in areas where temperatures will crush the copper...to remove particles and air in refrigerator to remove particles and air in conjunction with local plumbing code requirements. Allow enough flow... -
Recommended installation for electrical, drain and water supply connections for dishwashers.
... legs. Run wire into cabinet opening . How to a waste tee or waste disposer. If you have an air gap, make this answer more useful. The dishwasher warranty does not cover installation. View or purchase the necessary kits needed to connect a copper water supply line animation If you don't have a ¾" (1.90 cm) hose... -
Water supply hookup - Bottom freezer/French door refrigerators
... for non-water filter models Water filter models Materials needed : Flat-blade screwdriver 7/16" and ½" open-end wrenches or two adjustable wrenches ¼" nut driver and drill bit Cordless drill IMPORTANT: All installations must meet local plumbing code requirements. After connecting the refrigerator to be required in the copper tubing when bending the service...
Similar Questions
How To Replace Door Latch On Kitchenaid Kudc10fxss Dishwasher
(Posted by datgrgei 10 years ago)
How Big Does The Air Gap Need To Be In The Counter Top To Be?
(Posted by penlocke 12 years ago)