KitchenAid KSSO48FTX Support Question
KitchenAid KSSO48FTX Support Question
Find answers below for this question about KitchenAid KSSO48FTX - 48" - Refrigerator.Need a KitchenAid KSSO48FTX manual? We have 4 online manuals for this item!
Question posted by cabconcepts on September 15th, 2014
Inset Installation With Front Panels Being Flush With Cabinets On Left And Right
how much width do you need for the refrigerator opening with inset cabinetry when useing front panels to be flush with cabinets on the left and right?
Current Answers
Related KitchenAid KSSO48FTX Manual Pages
Use & Care Guide - Page 5
....
3. Open the freezer door and turn the refrigerator on your model, you have been connected to your refrigerator. For Style 2, move the switch to refill after cleaning refrigerator or changing light bulbs. A
Water System Preparation
Please read before you turn on the reverse osmosis system to the OFF (right) setting as shown. Immediately after installation, follow...
Use & Care Guide - Page 7
...REASON:
TEMPERATURE ADJUSTMENT:
REFRIGERATOR too cold Not set correctly for conditions
REFRIGERATOR Control 1° higher
REFRIGERATOR too warm High use or room very warm
REFRIGERATOR Control 1° lower... the refrigerator temperature rises above 48°F (9°C) or the freezer temperature rises above 15°F (-9°C) for longer than 10 minutes. Minimize door openings until ...
Use & Care Guide - Page 11
...left wall of the freezer stops the ice maker from producing ice if the door is open...flushed out of the system.
■ The quality of your ice maker.
■ Avoid connecting the ice maker to the OFF (right...by pushing it in the ON (left )
position. Empty the ice container. Use warm water to break up ) ...covering panel. Wash ice bin with both hands and press
the release button to the ON (left ...
Use & Care Guide - Page 16
...ice bin located on ? The refrigerator seems to make a new supply.
■ Does the freezer and ice bin need to be clogged or installed incorrectly.
See "Using the Control(s)."
■ Is ...that none have water in the OFF (right) position (on some models)? The filter may be cleaned? Check the filter installation instructions to the ON (left side of the bin and lift straight...
Dimension Guide - Page 1
... not kinked when the refrigerator is pushed into its final position.
A (see Installation
our products, we reserve the right to the height dimensions. For complete details, see chart following)
Model Width A (Trim edge to trim edge)
36
36¹⁄₄" (92.1 cm)
42
42¹⁄₄" (107.3 cm)
48
48¹⁄₄" (122...
Dimension Guide - Page 2
...;⁄₄" (48.9 cm)
51 ³⁄₈" (130.5 cm)
The location must permit both doors to open to a minimum of solid soffit
77" (196 cm)
A Width (see Installation
our products, we reserve the right to change without notice.
Instructions packed with product. to 47³⁄₄" (121.3 cm)
NOTE: Flooring under refrigerator must be...
Installation Guide - Page 6
...ordinances. ■ It is recommended that you need a ferrule, a union, and a ¹⁄₄" (6.35 mm) compression fitting. See "Opening
Dimensions." NOTE: A clearance of a cabinet run using a side panel to do not install the refrigerator near
an oven, radiator, or other heat source. ■ Do not install in an opening between cabinets or installed at the end of ¹⁄₂...
Installation Guide - Page 7
...; The water shutoff should be placed within 4" (10.2 cm) of the right side cabinets or end panel.
IMPORTANT: If this product is important to 47³⁄₄" (121.3 cm)
NOTE: Flooring under refrigerator must be plumb.
7 NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn...
Installation Guide - Page 8
... varies depending upon the width of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa) is used in the base cabinet on
either side of 40 to 60 psi (276 to the reverse osmosis system is less than 1" (2.54 cm) away from the right or left hand side cabinet or panel.
Reverse Osmosis Water...
Installation Guide - Page 13
... to use two 2" (5.08 cm) strips horizontally centered for added support.
14¹⁄₄" (36.2 cm)
10⁷⁄₈" (27.6 cm)
72¹⁄₄"
Freezer
(183.5 cm) Door Panel
(Non-Dispenser)
Refrigerator Door Panel
Overlay Panel
Spacer Panel
Spacer Panel
1/8" (3.18 mm)
Overlay Panel
33⁷⁄₈" (86.0 cm)
Dispenser cutout is centered left-to-right...
Installation Guide - Page 15
... for Non-dispenser Models
Color
36
42
48
White
#2325136 #2325137 #2325138
Black
#2325139 #2325140 #2325141
Stainless Steel
#2325142 #2325143 #2325144
Door Panel Part Numbers for installing the door handles. NOTES:
■ Two standoffs must be installed on side-by-side and bottomfreezer refrigerators that require overlay panels. Architect® Series handle (4396103)
B.
COLOR...
Installation Guide - Page 16
... Custom Panels
If you plan to install custom wood panels, you will need to 90 degrees. Make sure the refrigerator location allows the doors with extended handles to open to create the panels yourself or consult a qualified cabinetmaker or carpenter.
NOTE: The dashed lines in the illustration represent the location and offsets of raised wood panel. The refrigerator panel should...
Installation Guide - Page 17
... actual product dimensions and may not reflect the needed panel installation dimensions.
■ The side panel should be needed when not enough space is available to have cabinets on the top and bottom.
4.7 mm)
5.5 mm)
4.5 mm)
A
A
A 1.27 cm) Overlap
10 mm)
⁵⁄₈" (15.7 mm)
Inset Installation Dimensions
1. Refrigerator
24¹⁄₈" (61.3 cm)
A
23...
Installation Guide - Page 18
...a ³⁄₈"
(9.5 mm) board to hold the panel in the cabinet side trim. Flush Installation Dimensions
1. A
1.5 mm)
2.38 mm)
Inset Installation Dimensions
1. Add 0.8 mm) to this measurement to allow the side panel to fit into the trim. You may not reflect the needed installation dimensions.
■ The side panel should be needed when not enough space is available to have...
Installation Guide - Page 19
... final location.
2.
Model Reduced Tipping Radius
36
88" (223.5 cm)
42
88¹⁄₂" (224.8 cm)
48
89¹⁄₄" (226.7 cm)
1.
A. Place an appliance dolly under the refrigerator until refrigerator is in opening.
3. Remove the four brackets (two on each cabinet side trim to move and install refrigerator.
Push the top grille straight up;
Installation Guide - Page 20
... the bottom of refrigerator to fully cover the width of the compressor cover.
■ Locate the board(s) so the bottom surface(s) of copper tubing are ) 84" (213 cm) from the connection on before the refrigerator is installed.
■ Board(s) must be installed before the water line is recommended that leak. If not, use , the solid soffit...
Installation Guide - Page 21
... the washer is behind the refrigerator, a secondary water shutoff valve may help avoid filters and/or water valves from the left side of flexible codes approved water supply line to be installed in death, fire, or electrical shock.
1. 5. Fasten the shutoff valve to pass beneath the refrigerator without interference. Do not use an extension cord.
Installation Guide - Page 22
...;" (6 mm) max. Failure to move and install refrigerator. Move Refrigerator to its final location:
D
A. Do not remove film or cover. 3. Use two or more people to keep from left to right and front to raise the refrigerator until the top of the top soffit. The rollers should be needed after the custom panels are not interfering with the door...
Installation Guide - Page 24
... bottom side of the hinge using a Allen wrench. Slide the custom panels into the bottom and hinge side trims on the hinge side. Slide or snap the
screw covers into the hinge side trims.
A BC
A. Remove the locking plate as shown.
7. Open the freezer or refrigerator door. Turning the bushing right will lower the door...
Installation Guide - Page 26
... the top right side of ice. 3. Non-Dispenser Models 1. NOTE: Drive in the refrigerator and freezer compartments. 5. Additional flushing may spurt out of ice
to the midpoint setting. Open the freezer door and turn on disinfected waters that is cleared from your Use and Care Guide. Turn the refrigerator switch to the "Open" position. 2. Before using the water...
KitchenAid Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Refrigerator unlevel - Side by side refrigerator
... one-rotation increments. Grasp the grille with a standard-size kitchen cabinet. Do not unscrew the leveling bolts too much when lowering the refrigerator. Make sure all the way. Where applicable, use a ½" hex head socket or screwdriver to lower the refrigerator. this makes it will start to be flush with the side cabinets or cabinet end panels. -
Water supply hookup - Bottom freezer/French door refrigerators
... and ice maker. Connect the water supply to the refrigerator Click here for non-water filter models Water filter models Materials needed : Flat-blade screwdriver 7/16" and ½" open-end wrenches or two adjustable wrenches ¼" nut driver and drill bit Cordless drill IMPORTANT: All installations must meet local plumbing code requirements. Once water... -
Water supply hookup - Bottom freezer/French door refrigerators
... a water source or replacing the water filter, flush the water system. Do not use . Turn on the water supply to tubing length needed : Flat-blade screwdriver 7/16" and ½" open-end wrenches or two adjustable wrenches ¼" nut driver and drill bit Cordless drill IMPORTANT: All installations must meet local plumbing code requirements. To...
Similar Questions
Top Grill Assembly
I need the part number for the top grill assembly for a overlay panel assembly for ksso48.
I need the part number for the top grill assembly for a overlay panel assembly for ksso48.
(Posted by Romanbarrett 9 years ago)
How To Pull Out A Superba 48 Refrigerator
(Posted by arciSrtorr 9 years ago)
How To Install Panels On Kfc022evbl
(Posted by rroemfjo 9 years ago)
Appliance Panel Installation. Should There Be Parts For This?
(Posted by tonynleasa 11 years ago)
Opening Size Between Cabinets For Flush Application
(Posted by evelynh 12 years ago)