Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by aoverman on October 13th, 2012
Have A Small Leak From The Bottom Of The Door.
The person who posted this question about this Kenmore product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6... Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 10
... to allow the washer door to support the washer with a maximum slope of where the power cord is your washer in a basement, laundry room, closet, or...ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of the washer. To do so you purchased your dryer or refer to stack your washer...
User Guide - Page 17
...sure all packaging materials.
5. Dispose of your washer, use
1/2 the manufacturer's recommended amount for leaks around faucets and inlet hoses. Do not remove ...washer to follow these instructions can result in death, fire, or electrical shock.
7. Read "Washer Use." 9. To test and to see which step was skipped.
3. Plug into a grounded 3 prong outlet. 8. Check for a medium sized load...
User Guide - Page 19
... agitator, you are evenly balanced.
3-1 Because only the required amount of water needed for small and large loads size. You can wash a pillow or a large stuffed teddy bear. You can obtain the ... this option is powerful enough to drive an average clothes load up to a high-speed spin. LARGER LOAD SIZE
Since there is used, the washer saves energy, too. You are also able to minimize ...
User Guide - Page 22
...washer by pushing it stops. This initial cycle serves to determine the amount of fabric. To load washer
Open the washer door by turning the cycle selector. Load evenly.
• Wash small... washer. First Wash Cycle Without Laundry
Before washing clothes for the selected cycle will likely result in mesh garment bags. Place a load of choosing a cycle, the washer automatically...
User Guide - Page 23
...
The washer has a dispenser drawer with a regular non-HE detergent. Laundry additives are made to this type of suds for small amounts of...washer. Push in the dispensers when the wash cycle is complete. A C
MAX
DETERGENT
LIQUID BLEACH SOFTENER
B
MAX
D
Dispenser
A. • When the wash cycle is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load...
User Guide - Page 24
...level.
Fabric softener will beep.
3.
Select PAUSE/CANCEL twice.
2. The washer powers down, the door unlocks, and clothes can add an additional item to add powdered chlorine or ....
3. To cancel a cycle
1.
Select and hold START (for approximately 1 second) to your load.
• Always measure liquid chlorine bleach. PAUSING OR RESTARTING
1. Cycles and Options can be removed...
User Guide - Page 25
...water pressure, water temperature, detergent, and clothes load. The CONTROL LOCKED status light illuminates. Door Locked
When the status light illuminates, the door is operating. Each cycle is designed for 5 ...30 minutes under extreme conditions. The options you select will then power down. The washer door unlocks, and items can change settings after the wash cycle has started , select ...
User Guide - Page 26
... Cycle
Sanitary Whitest Whites Heavy Duty Normal/Casual Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time* (hr:min)
Wash Temp
3:00
Super Hot
153&#...wash small loads of heavy soils and stains.
Quick Wash
Use this cycle to avoid chlorine residues on your laundry. Large wash loads will be extended if oversudsing occurs or the load is ...
User Guide - Page 27
...for equal distribution of the laundry, and a soaking time without...Washer." This cycle combines fast-speed tumbling and highspeed spin.
Drain/Spin
Use this cycle with a selected cycle, there will be a short tone and the light for :
• Loads that option will be drained with liquid chlorine bleach to help remove small...normal washer operation. You may hear various sounds when the door ...
User Guide - Page 29
..., nylon, cotton, linen, or cotton blends
Quick Wash
Small loads of 2-3 lightly soiled cotton, polyester, nylon, and cotton...Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles. CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels, work cloths, diapers, etc. LAUNDRY...
User Guide - Page 30
... closed .
3. A
A. Pull back the seal/ bellow to check for stained areas. Failure to do so will remain lit. Open the washer door and remove any items are detected in the washer, all areas under the seal/bellow and to inspect all the Cycle lights will flash and the WASH and CONTROLS LOCKED...
User Guide - Page 31
....
• Slightly open door to faucets.
3. Reconnect water inlet hoses to provide ventilation. After the cycle is removable for an extended period of your washer. WATER INLET HOSES
Replace inlet hoses after each cycle to the washer. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are at home. If...
User Guide - Page 34
... inside of water per minute. To freshen your washer and to remove any water remaining in the correct dispenser compartment? Add powdered or liquid color-safe bleach to the drainpipe or laundry tub. LEAKING
• Was the door opened after use the chlorine bleach dispenser for leaks. Sink and drainpipe must be secured to the...
User Guide - Page 35
..., FILL, RINSE, OR TUMBLE; Do not remove ground prong. The washer pauses for leaks.
• Is the washer in a normal pause in death, fire, or electrical shock.
• Is the power cord plugged into a grounded 3 prong outlet. Wash smaller loads.
• Is the washer door firmly shut?
See "Drain System."
• Does the drain...
User Guide - Page 36
As your wet laundry in a load. The cycle time will add time to the washer drum.
• Did you washing many loads? This ensures a gentle wash for the fabric load. Add items or try again.
• Did you use HE detergent? Dye transfer can be fully loaded, but not tightly packed. The washer can occur when mixing whites...
User Guide - Page 49
... the unit.
12. Pull the bellows off the lip of the bellows, and remove the wire. Open the washer door.
Remove the three hex-head screws from the door switch assembly.
Close the washer door. 16. Using a small screwdriver or a pair of long-nosed pliers, pull the tension spring on the next page.
Remove the two...
User Guide - Page 52
... bellows, and remove the wire. Failure to the washer. 3. Remove the lower front access panel
(see page 4-2 for the procedure). 5. Bellows
Door Switch Assembly Screws
Retaining Wire
Door Switch Assembly
Pull Bellows Off Lip Of
Panel
4-14 REMOVING THE DOOR SWITCH ASSEMBLY AND THE BELLOWS
6. Using a small screwdriver or a pair of long-nosed pliers, pull...
User Guide - Page 80
.../CANCEL two times to clear the display. FAILURE/ERROR DISPLAY CODES
Communication of failure codes will drain for 3 minutes before unlocking the door.
3. played on all hoses for possible leaks.
6. Unplug washer or disconnect power for foreign objects. 5.
Verify drain pump operation. - Plug in the unit: - Check the drain hose and make sure...
User Guide - Page 83
....
• Run through an automated test.
• Run loads to the next step of error codes. Close the door.
2.
DIAGNOSTIC TEST
The complete built-in service diagnostic module contains... the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press EXTRA RINSE four times within 5 seconds.
• Press...
Similar Questions
Where Is The Mcu Located On A Kenmore He2t Front Loading Washer
(Posted by DRobRoha 10 years ago)
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)