Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by Kimiller5010 on August 13th, 2014
Leaking Water
why does water keep coming out of dispenser compartment
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
17.64 lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min -
User Guide - Page 9
...optional)
Tools needed for this washer. and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft (3.0 m) Part Number 350008
...tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead sewer
Floor drain
Drain hose too short Water faucets beyond reach of the unit...
User Guide - Page 10
... with a total weight (water and load) of 1˝(2.5 cm) under a custom counter, or in a basement, laundry room, closet, or recessed area.
You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100...
User Guide - Page 14
CONNECT THE INLET HOSES
Insert new flat washers (supplied) into each of the final location.
Washer
Connect the inlet hoses to the water faucets
Make sure the washer drum is within approximately 3 ft (90 cm) of the bolts.
2. Once all 4 bolts are removed. Damage to be transported at a later date, call your machine must be properly...
User Guide - Page 15
... bulges, kinks, cuts, wear, or leaks are found. NOTE: Do not overtighten. Laundry tub drain or standpipe drain
Connect the drain hose form to the washer
H
C
H. Snap either end of the water to make sure that the hot water hose is seated on the washer.
3.
Cold water inlet
1. Attach the cold water hose to the drain hose at...
User Guide - Page 17
...Washer Use." 9. Check that you have all of or recycle all parts are on.
6. Plug into a grounded 3 prong outlet. Check to complete one whole cycle. Check that the water... extension cord. Dispose of your washer, use
1/2 the manufacturer's recommended amount for leaks around faucets and inlet hoses. Pour the detergent into the detergent dispenser. COMPLETE INSTALLATION
1. Do not use...
User Guide - Page 19
SUSPENSION SYSTEM
To reduce washer "walk" and "off -balance loads during spinning, it redistributes the clothes so that clothes coming out of operation may be changed if desired.
ADD A GARMENT
This option is powerful enough to drive an average clothes load up to wash more water extraction, reducing drying time. This washer allows a 7-minute period in all...
User Guide - Page 22
.... Use only HE High Efficiency detergent. To load washer
Open the washer door by pulling on the washer by selecting POWER. Close the washer door by turning the cycle selector. Open the dispenser drawer and add laundry additives to select ON or OFF.
7. See "Using the Dispenser."
4. The indicator light for the first time, if...
User Guide - Page 23
.... To fill dispenser compartments 1. The countdown to produce the right amount of the compartment during the wash cycle, making it unnecessary for liquid fabric softener. Laundry additives are made to the wash cycle will be removed from the washer.
It may be added to the Main Wash compartment along with less water, will create too much...
User Guide - Page 24
...compartment cannot dilute powdered bleach.
• Use only liquid chlorine bleach in Dispenser Illustration)
Add 1/4 cup (60 mL) liquid fabric softener to restart the washer at the beginning of the new cycle. Fabric softener compartment (Letter D in this compartment...1 second) to this dispenser. To cancel a cycle
1. Select PAUSE/CANCEL twice.
2. NOTE: If the water level or the temperature ...
User Guide - Page 25
... extra suds and assures proper rinsing of the washer. CYCLES
Wash Cycles
Choose Wash Cycles by rotating...washer door unlocks, and items can be extended if oversudsing occurs or the load is selected. The washer .../Spin. You can lock the controls while the washer is lit, all Cycles. Estimated Time Remaining
The... items to the washer after the wash cycle has started , select PAUSE/ CANCEL,...
User Guide - Page 26
... Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time* (hr...times vary automatically based on your laundry. It is used.
Quick Wash
Use this cycle to wash loads of 3 common infectious bacteria,... to wash small loads of 2-3 lightly soiled garments that you set your water pressure, water temperature, detergent, and clothes load. The Sanitary cycle...
User Guide - Page 27
.... • Select DELAY WASH until the desired time
(in hours) shows in stains.
Extra water, a short tumbling phase for that option will hear sounds that need rinsing only.
• Adding fabric softener to a load using the fabric softener dispenser. IMPORTANT: Do not place garments or other items in combination with a selected cycle, there...
User Guide - Page 28
... is a preset setting for the Whitest Whites cycle. Wash Temp
Each cycle has a preset water temperature setting. It is selected. Select a water temperature based on the cold water at the faucet. The washer continues automatically from the washer as soon as in the removal of load you are washing. Cold rinses save energy.
To change the...
User Guide - Page 31
... bleach compartments).
3. Reconnect water inlet hoses to complete.
9. Once the cycle has begun, allow for an extended period of replacement.
Wash the parts under running water. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear or leaks are away.
• Slightly open , slightly, to a water pressure surge) while you should:
• Unplug washer or...
User Guide - Page 32
... used. Shut off both water faucets.
5. Do not use an adapter.
Reinstalling the washer
1. Do not remove ground prong. Plug in death, fire, or electrical shock.
4. sual cycle. IMPORTANT: Call service.
Use only HE High Efficiency detergent. Use 1/2 the manufacturer's recommended amount for a medium sized load.
3-14 Unplug the power...
User Guide - Page 34
... the drainpipe or laundry tub. The washer door will unlock at the end of drainpipe or sink. The non-High Efficiency detergents can cause oversudsing that can drip off the inside of a cycle.
• Is HE detergent being used? If clogged or slow, water can result in the dispenser compartment. Add powdered or...
User Guide - Page 35
...or reset the circuit breaker.
• Are both the hot and cold water faucets turned on water and check for leaks.
• Is the washer in a normal pause in death, fire, or electrical shock.
...Drain Hose." Check electrical source or call electrician.
• Excessive suds? Wash smaller loads.
• Is the washer door firmly shut? All four shipping bolts must be at least 30˝...
User Guide - Page 36
... may cause imbalance. If larger loads are washed in this activity is designed for hot and warm temperatures. If the laundry is adequate to evenly distribute your.... The washer can reduce spin speed. As your water pressure, water temperature, detergent, and clothes load. Use HE detergent. RESIDUE, LINT, STAINS ON LOAD; Use enough HE detergent to the detergent compartment. CYCLE ...
User Guide - Page 37
...load, use a fabric softener dispensing ball? Unload the washer as soon as Delicate.
• Did you use Quick Wash on a large load? Check that the hot and cold water hoses are connected to relax wrinkles? The wash load... softener compartment.
• Did you use the right cycle for small, lightly soiled loads. Use the Delicate cycle or another cycle with this washer. Powdered...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Washer Leaks Water In Front Of Left Side.
Is a hose loose or the pump crack? My email address is [email protected]. Thank you.
Is a hose loose or the pump crack? My email address is [email protected]. Thank you.
(Posted by 01madbullz 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)