Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by danvanthiel on April 18th, 2013
He2t.f20 And...
All lights blinking, f20. Took apart hoses, no plug nor kink. next load ok. Next load, all lights blinking, water won't fill up. This machine is not that old and it has been treated well. NOT HAPPY!
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 2
... of this Job Aid is to provide information that will enable the service technician to properly diagnose malfunctions and repair the Duet Sport™ Front-Loading Automatic Washer.
ii - For specific information on the installation, operation, and service of this Job Aid is typical and should be used in this Job Aid...
User Guide - Page 6
MODEL & SERIAL NUMBER DESIGNATIONS
MODEL NUMBER
MODEL NUMBER
W F W 8 3 00 S W 0
BRAND W = Whirlpool
ACCESS F = Front Loading
PRODUCT W = Washer
SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load
6 = Oasis 8 = Mid Line Front Load
PRICE POINT LEVELS (1 - 9)
TRADE PARTNER ID (00 = BRANDED)
YEAR OF INTRODUCTION S = 2006, T = 2007
COLOR CODE T = Biscuit Q = White W = ...
User Guide - Page 8
..." 242 lbs.
17.64 lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 9
...; Level • Wood block • Ruler or measuring tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead sewer
Floor drain
Drain hose too short Water faucets beyond reach of the unit. Transit bolt hole plug E. If you are in the "Use & Care Guide." Remember that open to Buy
Sump...
User Guide - Page 10
... allow the washer door to support the washer with a total weight (water and load) of the washer. Installation Clearances
• The location must be considered.
You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of...
User Guide - Page 14
... date, call your machine must be properly set up for relocation by hand until the bolts are removed. NOTE: If the washer is within approximately 3 ft (90 cm) of the final location.
Attach a hose to the cold water faucet.
There are removed, discard the bolts and spacers.
Coupling B.
Attach a hose to the hot water faucet. CONNECT THE...
User Guide - Page 15
... replace hoses if bulges, kinks, cuts, wear, or leaks are found.
Attach the cold water hose to the corrugated drain hose. Turn on the hoses for leaks. B. Bend drain hose over drain hose form and snap into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that the cold water hose is seated on the washer.
2. Record hose installation...
User Guide - Page 17
... on.
6. Do not use
1/2 the manufacturer's recommended amount for leaks around faucets and inlet hoses. Plug into the detergent dispenser. To test and to complete one whole cycle. Use only HE High Efficiency detergent.
2-9 Dispose of your washer, use an adapter. Do not remove ground prong. Failure to see which step was skipped...
User Guide - Page 19
... load machines. PRODUCT OPERATION
FEATURES AND BENEFITS
The front-loading high efficiency washer was designed to conserve resources and lower your new washer ...light will have less moisture than for a conventional washer. LARGER LOAD SIZE
Since there is available in which means fewer loads. In addition, if the Dynamic Balance system detects off -balance" conditions, your water...
User Guide - Page 20
SMART DISPENSERS
The three compartments in the dispenser allow loading of the cycle, and the bleach is
added after the enzymes have had a chance to do their cleaning. The...or in the detergent advantage system.
The additives will be dispensed into the wash at the beginning of all laundry additives before the washer is added at the optimal time for cleaning. The detergent is started.
User Guide - Page 22
...it without clothes. First Wash Cycle Without Laundry
Before washing clothes for the selected cycle will...load. Place a load of choosing a cycle, the washer automatically shuts off.
3-4 The door can be opened only if PAUSE/CANCEL is selected while the ADD A GARMENT light... with less water, will illuminate. HE detergents are made to determine the amount of fabric. Washer door should be...
User Guide - Page 23
...laundry additives to avoid a spill).
The package for this compartment for your laundry additives-one is for detergent, one is for liquid chlorine bleach, and one is for small amounts of water..., the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be marked "HE" or "High Efficiency." The washer powers down the washer manually after the cycle is...
User Guide - Page 24
...(for approximately 1 second). STATUS LIGHTS
These lights show which portion of the cycle the washer is complete, the door unlocks..... NOTE: If the water level or the temperature is selected. To drain the washer manually
1. Select DRAIN/SPIN...machine will drain automatically before START is too high, the washer will beep.
3. The liquid detergent flows immediately into the washer...
User Guide - Page 25
...The cycle times vary automatically based on the stage of your water pressure, water temperature, detergent, and clothes load.
To change up to 30 minutes under extreme conditions. ... Complete light stays on for approximately 1 second) to the washer after the Add a Garment period, press PAUSE/CANCEL twice. The washer will illuminate.
The CONTROL LOCKED status light illuminates....
User Guide - Page 26
... proper performance during this cycle.
This cycle combines a super hot water temperature and fast speed tumbling to help ensure the removal of 2-3 lightly soiled garments that you set your water pressure, water temperature, detergent, and clothes load. Normal/Casual
Use this cycle to wash loads of bleach.
High-speed spin helps shorten drying time. This cycle...
User Guide - Page 35
..., for 1 second? The top of the drain hose more than 30˝ (76 cm) on ? Add more frequently when a non-HE detergent is used.
• Is the load balanced? You will occur more items or redistribute the load. WASHER STOPS
Electrical Shock Hazard Plug into a grounded 3 prong outlet? Plug power cord into a grounded 3 prong outlet.
•...
User Guide - Page 37
... small, lightly soiled loads. Unload the washer as soon as it stops.
• Did you use a fabric softener dispensing ball? If safe for slow-speed cycles such as Delicate.
• Did you overload the washer? For best results, use liquid detergent for load, use warm or hot wash water.
• Are the hot and cold water hoses reversed...
User Guide - Page 80
... the WASH cycle. Possible Causes/Procedure 1.
Possible Causes/Procedure 1. Plug in washer or reconnect power. 6. Reference Status LEDs chart, page 6-4
NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH TRIP NOT DETECTED. Make sure that the pressure switch hose is not tripped after 3 minutes. Unplug washer or disconnect power. 8. Possible Causes/Procedure Door lock mechanism...
User Guide - Page 81
... 1. Unplug washer or disconnect power. 2. Check wire harness connections to the drain pump, pressure switch, water inlet value,... close the door.
2.
Check the drain hose and make sure it is broken. Check... 2.
Possible Causes/Procedure 1.
LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is... Unit (CCU) is not plugged or
kinked.
2. Unplug washer or disconnect power.
3. Check...
Similar Questions
Washer Capacity
Hi,What is the cubic capacity of a kenmore 110.29822801
Hi,What is the cubic capacity of a kenmore 110.29822801
(Posted by juliettemallen 6 years ago)
Follow Up To The Kenmore He2t Washer F20 Error Code.
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
(Posted by riskoj 7 years ago)
Kenmore 417.41122(last 3 Are 340 I Think) Washer
My washer will start a cycle. Run for 2 minutes, filling the drum with water, and then skip forward ...
My washer will start a cycle. Run for 2 minutes, filling the drum with water, and then skip forward ...
(Posted by Demovicchuck 8 years ago)
How Can I Clean My Kennmore Washer Machine?
(Posted by Mariavargas1102 9 years ago)
Flashing F21 Light And Water Pooling In Washer.
I was washing a load of clothes when my washer stopped and F21 light was flashing. Clothes was soake...
I was washing a load of clothes when my washer stopped and F21 light was flashing. Clothes was soake...
(Posted by ocorona213 11 years ago)