Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by ruskasimeonova on January 5th, 2013
F20
As soon as the machine is filled with water it will stop and F20 displays. While if you program the washer on rinse and spi it works perfectly, and agitate and drain well.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 2
... and diagnose malfunctions. • Successfully perform necessary repairs. • Successfully return the washer to properly diagnose malfunctions and repair the Duet Sport™ Front-Loading Automatic Washer.
GOALS AND OBJECTIVES
The goal of the Duet Sport™ Front-Loading Automatic Washer. Copyright © 2006, Whirlpool Corporation, Benton Harbor, MI 49022
- Always use the...
User Guide - Page 6
MODEL & SERIAL NUMBER DESIGNATIONS
MODEL NUMBER
MODEL NUMBER
W F W 8 3 00 S W 0
BRAND W = Whirlpool
ACCESS F = Front Loading
PRODUCT W = Washer
SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load
6 = Oasis 8 = Mid Line Front Load
PRICE POINT LEVELS (1 - 9)
TRADE PARTNER ID (00 = BRANDED)
YEAR OF INTRODUCTION S = 2006, T = 2007
COLOR CODE T = Biscuit Q = White W = ...
User Guide - Page 8
..." 242 lbs.
17.64 lbs. (8 kg)
N/A
36.0" 30.00"
27" 242 lbs.
1-4 IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 9
... Height
Approximate Height with Washer
Color
Model Number
10" (25.4 cm) 46" (116.8 cm) White WHP1000SQ
15.5" (39.4 cm) 51.5" (130.8 cm) White WHP1500SQ
2-1 additional drain hose Part Number 8318155; E
A. Transit bolt hole plug E. and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10...
User Guide - Page 10
... under entire washer. Some water can remain in a basement, laundry room, closet, or recessed ...water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of the washer...
User Guide - Page 12
... the bottom of 2˝ (5 cm).
wall or floor (views A & B)
The standpipe drain requires a minimum diameter standpipe of the washer. The top of the standpipe must be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Laundry tub drain system (view A)
The laundry tub needs a minimum 20 gal. (76 L) capacity.
User Guide - Page 14
... hoses to the cold water faucet. Once the bolt is loose, move and install washer. Screw on coupling by a certified technician. INSTALLATION INSTRUCTIONS
REMOVE TRANSPORT SYSTEM
4. IMPORTANT: Position the washer so that support the suspension system during transportation.
Failure to do so can result. NOTE: If the washer is within approximately 3 ft (90 cm) of...
User Guide - Page 15
... drain hose form and snap into a laundry tub, drainpipe or bucket, to the cold water faucet. Connect the inlet hoses to reduce the risk of particles in the water lines that the cold water hose is seated on the water faucets completely and check for future reference. ROUTE THE DRAIN HOSE
Proper routing of use to the washer...
User Guide - Page 20
... in the detergent advantage system. The additives will be dispensed into the wash at the beginning of all laundry additives before the washer is started.
The bleach release system is included in the EXTRA RINSE, if selected. Use only HE High Efficiency detergent.
3-2 The detergent is added at the optimal time for cleaning...
User Guide - Page 22
...Without Laundry
Before washing clothes for this type of detergent will illuminate. To load washer
Open the washer door by selecting POWER. Overloading can cause poor cleaning.
• The washer can... Modifiers and Options, Water Temp, and Spin Speed for the selected cycle will likely result in washer errors, longer cycle times, and reduced rinsing performance. The signal is recommended...
User Guide - Page 23
... door unlocks, and the wash load can be marked "HE" or "High Efficiency." Main Wash detergent compartment C. To begin the wash cycle later
Select DELAY WASH until the desired delay time (in washer errors, longer cycle times, and reduced rinsing
performance.
Laundry additives are made to the washer during Delay, before the wash...
User Guide - Page 26
... Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time* (hr:min)
Wash Temp...The cycle times vary automatically based on your laundry. The cycle time will result in a hurry...water pressure, water temperature, detergent, and clothes load. Large wash loads will be extended if oversudsing occurs or the load is recommended that are needed in the machine...
User Guide - Page 27
... spots of set -in stains.
Rinse/Spin
Use this cycle to drain your washer or to drain and spin your wash load.
NOTE: Loads of synthetics, delicate fabrics, handwashables, and woolens should be drained with no spin or low spin to help improve the removal of set -in the Estimated Time Remaining display. • Select START. These new...
User Guide - Page 28
...; ATC works for loads of Cycle Signal
This signal is a preset setting for fabrics. This option adds tumbling time prior to the Main Wash Compartment of detergent or bleach residue from the washer as soon as in the normal rinse. It is helpful when you are removing items from garments. The water temperature for all rinse cycles...
User Guide - Page 29
CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels, work cloths, diapers, etc. LAUNDRY GUIDE
Refer to each of
Wash Cycle ... special care items marked "Hand Washable"
Clean Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles.
Listed to the right are the options...
User Guide - Page 36
... a large load on your wet laundry in suspension.
• Do you have you overload the washer? This ensures a gentle wash for the fabric load. Follow manufacturer's recommendations for hot and warm temperatures. Use more detergent for the load being washed? For best performance, use small loads. WASH / RINSE TEMPERATURE
• Are the hot and cold water inlet hoses...
User Guide - Page 81
...stop the motor, the MCU will show. Check the drive motor for foreign objects. 2. Unplug washer...drain pump, pressure switch, water inlet value, and Central Control Unit (CCU).
4. Check connections of foreign objects.
5. Verify CCU operation by looking for operations of the CLEANING WASHER cycle a load...Continuity tests. DISPLAY
EXPLANATION AND RECOMMENDED... machine shuts down .
Make sure...
User Guide - Page 82
... or any detergent. Run the unit through a RINSE/SPIN cycle. - Unplug washer or disconnect power. 3. Check drain pump. 7. Check the pressure switch. 8. Verify CCU operation by the pressure switch during the drain or spin phases, the washer will fill 4 liters of water and during 5 minutes the unit will be drained and it is not plugged or kinked.
2. Failure...
User Guide - Page 89
... the MCU by listening for a click in the CCU when unit is plugged into a working outlet and for each problem.
1. Unplug washer or disconnect power.
4. Verify the unit is locked, drain the unit.
4. Check for operations of line cord and line filter.
5. Check water connections to confirm the touchpad/LED is level. 2. Check pump...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)