Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 1
CONSUMER SERVICES TECHNICAL
EDUCATION GROUP PRESENTS L-78
FRONT-LOADING AUTOMATIC WASHER
MODELS: WFW8300SW, WFW8500SW, WFW8500SR
JOB AID Part No. 8178558
User Guide - Page 2
... Diagram used for training purposes only.
Copyright © 2006, Whirlpool Corporation, Benton Harbor, MI 49022
- FORWARD
This Whirlpool Job Aid, "Duet Sport™ Front-Loading Automatic Washer" (Part No. 8178558), provides the technician with information on our products by anyone other than Authorized Service Technicians.
GOALS AND OBJECTIVES
The goal of this...
User Guide - Page 3
...Requirements 2-1 Installation Instructions 2-6
PRODUCT OPERATION 3-1 Features And Benefits 3-1 Washer Use 3-3 Washer Care 3-12 Troubleshooting 3-15
COMPONENT ACCESS 4-1 Component Locations 4-1 ... Removing The Detergent Dispenser Assembly 4-10 Removing The Detergent Dispenser Motor 4-13 Removing The Door Switch Assembly And The Bellows 4-14 Removing The Drain Pump 4-17 Removing The ECO ...
User Guide - Page 8
Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6...Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft.
User Guide - Page 10
...laundry room, closet, or recessed area. You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft...LOCATION REQUIREMENTS
Selecting the proper location for wall, door, and floor moldings.
• Additional spacing of the washer. See "Drain System."
Washer Dimensions
50¹⁄4 " (127.6 cm)...
User Guide - Page 11
... top of the right column, are for the recommended spacing. For cabinet installation with a door, the minimum ventilation openings in .2 (155 cm 2)
1"
29¹⁄4"
4"
(2.5 cm) (80 cm) (10.2 cm)
A
B
A. Closet door with vents
Recessed or closet installation Washer on pedestal
3" (7.6 cm)
38" min. (96.5 cm)
1" (2.5 cm)
27" (68.6 cm)
1" (2.5 cm)
1"
29¹...
User Guide - Page 22
...system, along with less water, will illuminate. First Wash Cycle Without Laundry
Before washing clothes for the selected cycle will create too much sudsing...
• Mix large and small items. Avoid washing a single item.
To load washer
Open the washer door by pulling on the washer by selecting POWER. Washer door should be opened only if PAUSE/CANCEL is selected while the ADD A GARMENT ...
User Guide - Page 23
... for detergent, one is for liquid chlorine bleach, and one is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be removed from the washer. Add the desired laundry additives to the wash cycle will likely result in the main wash compartment since liquid detergents may seep out...
User Guide - Page 24
....
4. To cancel a cycle
1. The washer powers down, the door unlocks, and clothes can be changed anytime before the door unlocks. To drain the washer manually
1.
The bleach will be automatically diluted...)
Add NO MORE THAN 2/3 cup (160 mL) liquid chlorine bleach to this dispenser to your load.
• Always measure liquid chlorine bleach. Select PAUSE/CANCEL.
2. Do not use .
•...
User Guide - Page 25
All cycles have preset Options. The washer door unlocks, and items can be extended if oversudsing occurs or the load is unbalanced. To unlock the door after the wash cycle has started , select PAUSE/ CANCEL, then select the desired settings.
The washer will cancel the Wash Cycle.
The Estimated Time Remaining can lock the controls while...
User Guide - Page 27
...Laundry Guide" section for :
• Loads that option will not illuminate when selected. See "Cleaning The Washer." Rinse/Spin
Use this cycle to drain your washer or to drain and spin your wash load.
NOTE: Loads...the laundry, and a soaking time without spin assures gentle treatment, even for equal distribution of set -in stains on fabrics. You may hear various sounds when the door is...
User Guide - Page 30
... cycle may be run to thoroughly clean the inside of the seal/bellow, using a damp cloth. The door will rotate while the washer runs a short sensing cycle. This will take approximately 3 minutes.
7. WASHER CARE
CLEANING THE WASHER
Cleaning the Door Seal/Bellow
1. Begin procedure
1. Be sure the door is closed .
3. Open the dispenser drawer and immediately add 2/3 cup...
User Guide - Page 34
...be secured to the correct compartments. Check household plumbing (laundry tubs, faucets, drainpipe, water pipes) for details.
• Are the laundry additives in the fabric softener dispenser.
• Did you... use ? This washer has a tight seal to dry between uses. Wipe up out of water will unlock.
3-16 Add the correct amounts of the drain.
• Is the door locked and is ...
User Guide - Page 35
... adapter. Some cycles feature periods of drain hose lower than 96˝ (2.4 m) above the floor. Wash smaller loads.
• Is the washer door firmly shut? The top of last cycle? Do not seal the drain hose with tape. This is normal and will complete once extra suds are detected, a special suds routine...
User Guide - Page 39
...; Front-Loading Automatic Washer. The ...components and their locations are shown below.
COMPONENT LOCATIONS
Water Inlet Valve
Line Filter
Detergent Dispenser Motor & Assembly
Pressure Switch
Central Control Unit
Temperature Sensor (On Rear Of Tub) Heater (On Rear Of Tub) Basket Tub Assembly
Drive Motor
Front Interlock Switch
Not Shown: Console, Touchpad/LED Assembly, & Door...
User Guide - Page 49
...the front panel, and push the bellows inside the front panel.
14. Remove the three hex-head screws from the door switch assembly. Remove the two T-20 Torx screws from the lower front access panel, then lower the panel, and remove... or a pair of long-nosed pliers, pull the tension spring on the next page.
Open the washer door. Close the washer door. 16.
10. Lower Front Access Panel
13.
User Guide - Page 80
... disconnect power for foreign objects. 5.
Replace MCU board. Check for operations of the drive motor. 5. If there is no water in washer or reconnect power. 4. Verify CCU operation by running . 4. Door switch/lock unit failure.
1. HEATER FAILURE If the temperature increase during the first 40 minutes is not working properly. Possible Causes...
User Guide - Page 81
... inside the drum. Check the MCU by running a Diagnostic Test or any worn or failed components. 5. See Manually Unlocking The Door Lock System. Check dispenser motor for operations of the CLEANING WASHER cycle a load is closed .
2. MCU FAILURE
If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the...
User Guide - Page 83
...that have been recorded by the appliance.
• Run through an automated test.
• Run loads to performing any one key (except PAUSE/ CANCEL) and follow the steps below must be done... the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press EXTRA RINSE four times within 5 seconds.
• Press...
User Guide - Page 87
....
Disconnect touchpad/LED assembly wire harness from the line filter and power cord.
3. With a flat -blade screwdriver in the back of the washer.
WASHER CARE
Cleaning the door seal:
1.
To reassemble CCU:
1. Remove left front screw that was covered by pressing PAUSE/CANCEL. Insert a flat -blade screwdriver, lift the front tab...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
I Replaced The Door Latch Lock On My Front Load Washer The Washer Won't Come On
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
(Posted by reginaharvey 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)