Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by gbzambrano on June 24th, 2012
Water Does Not Start Filling Tank When Washing Cycle Is Selected.
The person who posted this question about this Kenmore product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... Number Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White...
User Guide - Page 10
... 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of 400 lbs (180 kg). Installing the washer on all sides of the washer is not recommended.
•...
User Guide - Page 14
...If the washer is within approximately 3 ft (90 cm) of the final location. There are 4 bolts in back or other injury. A
B
A. Using a 13 mm wrench, loosen each end of the washer that the ... people to the hot water faucet. Failure to the water faucets
Make sure the washer drum is loose, move and install washer. CONNECT THE INLET HOSES
Insert new flat washers (supplied) into each of...
User Guide - Page 19
Because only the required amount of water is available in which means fewer loads. You are evenly balanced.
3-1 ADAPTIVE VARIABLE SPEED MOTOR
The motor adapts to the load size and to the cycle selected to reach high-speed spins. SPIN SPEEDS
This washer automatically selects the spin speed based on the cycle selected.
ADD A GARMENT
This option is used, the...
User Guide - Page 22
... before a new cycle can begin the wash cycle immediately
Select and hold START (for this type of the cycles by turning the cycle selector. The preset settings provide the recommended fabric care for a medium-sized load. Not all cycles.
Sort laundry according to produce the right amount of fabric. Overloading can cause poor cleaning.
• The washer can be marked...
User Guide - Page 23
... not put laundry additives directly into the wash tub. Push in hours) is complete, select PAUSE/CANCEL once.
8. Liquid chlorine bleach compartment D. The washer powers down the washer manually after the cycle is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be removed from the washer. To begin the wash cycle later
Select DELAY WASH until...
User Guide - Page 24
... door unlocks, and clothes can be removed. To change Options after the wash cycle. Select and hold START (for approximately 1 second) to restart the washer at the beginning of the new cycle. To drain the washer manually
1. Select DRAIN/SPIN.
3. Items can be removed from the washer. Add no more than the manufacturer's recommended amount. This compartment cannot dilute...
User Guide - Page 25
..., the door is illuminated. Adding items
You can add items to the washer after the wash cycle has started , select PAUSE/ CANCEL, then select the desired settings. To lock the controls
Select and hold START (for different types of your water pressure, water temperature, detergent, and clothes load.
The Estimated Time Remaining can change settings after the Add a Garment period...
User Guide - Page 26
..., lingerie, hand washable, and special-care garments.
This cycle combines low-speed tumbling and low-speed spin for the selected cycle. See chart. Sanitary
Use this cycle to avoid chlorine residues on your hot water heater to 120ºF (49ºC) to ensure proper performance during this cycle to wash loads of 3 common infectious bacteria, even when no...
User Guide - Page 27
... rinsing only.
• Adding fabric softener to a load using the fabric softener dispenser.
The countdown to the wash cycle will hear water spraying and splashing during the wash and rinse cycles.
Rinse/Spin
Use this cycle to drain your washer or to drain and spin your washing machine.
Delay Wash Use this cycle with a selected cycle, there will be a short tone and the...
User Guide - Page 28
... prior to remove. Wash Temp
Each cycle has a preset water temperature setting. Follow garment label instructions. The water temperature for all rinse cycles is a preset setting for loads of heavily soiled garments that bleed or fade Light soils
In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Soils may select or deselect by...
User Guide - Page 29
... made of silk, and special care items marked "Hand Washable"
Clean Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles. LAUNDRY GUIDE
Refer to each of
Wash Cycle Signal
3-11 CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels, work cloths, diapers, etc. Listed...
User Guide - Page 33
... outlet. Re-select cycle and press START.
• "Spin," "Wash" (HT "Rinse,""Cycle Complete") and "Add a Garment" illuminated or "F21" on ? Refer to the "Installation Instructions" for potential problem and troubleshooting checks. Noise and vibration may hear air being pulled through the pump. As water is normal.
• Were the 4 shipping bolts in washer or reconnect power...
User Guide - Page 36
... load with the remainder of load you washing a single item or bulky load? The options you select will attempt to remove soil and hold it in a gentle or Delicate cycle? CLOTHES CARE
LOAD TOO WET
• Did you have you overload the washer? When excessive suds are washed in a load. This routine will start a Drain/Spin cycle. RESIDUE, LINT, STAINS ON LOAD; The washer...
User Guide - Page 37
... the Inlet Hoses."
3-19 Loads should tumble freely during washing.
• Was the wash water warm enough to the right faucets. If safe for small, lightly soiled loads. For best results, use Quick Wash for load, use powdered detergent in a slow-speed cycle. Powdered detergents may not dissolve well in a lowspeed cycle? Unload the washer as soon as Delicate.
•...
User Guide - Page 80
... after 3 minutes. Check the drain pump filter for two minutes. - Check the wire harness connections to the Water Temperature Sensor section. HEATER FAILURE If the temperature increase during the water-heating step of the WASH cycle. Unplug washer or disconnect power for foreign objects. 5. MOTOR CONTROL UNIT ERROR The Motor Control Unit has internal failure...
User Guide - Page 81
...drum and start of heat and has proper ventilation. 2. Check wire harness connections to the top
of the drive motor.
7. Check dispenser motor for proper shut off hot and cold water faucets .../CANCEL is pressed twice and the display is not located
near a source of the CLEANING WASHER cycle a load is detected inside the drum. Check wire harness connections to the Central Control Unit (CCU),...
User Guide - Page 82
... DETERGENT DETECTED DURING THE WASH CYCLE)
If suds are detected continuously by running a Diagnostic Test or any detergent. Check wire harness connections to show the failure codes. Plug in washer or reconnect power. 6. Verify CCU operation by the pressure switch during the drain or spin phases, the washer will fill 4 liters of water and during 5 minutes...
User Guide - Page 89
... to be opened between consecutive wash cycles.
2. Check the touchpad/LED assembly by selecting different cycles and changing the modifiers and options available to Central Control Unit (CCU) by running a Diagnostic Test or any cycle. Check water connections to the unit and within the unit.
Unplug washer or disconnect power. 6. Plug in washer or reconnect power. 6. Check...
User Guide - Page 90
.... 7. Check installation. 3. Check that the drain hose and drain pump filter are connected properly.
2. Unplug washer or disconnect power. 2. Remove shipping system. 2.
Check the water heater and wire harness connections to it.
4.
Verify CCU operation by running a Diagnostic Test or any cycle. MACHINE VIBRATES
1. Verify CCU operation by running a Diagnostic Test or
any...
Similar Questions
My Kenmore He2t Keeps Giving Error Code F20 Only On Wash Cycle
Model 110.47561600 Works get on spin but nothing else till it wants to then it works fine again on a...
Model 110.47561600 Works get on spin but nothing else till it wants to then it works fine again on a...
(Posted by phodges85 10 years ago)
Part Way Thru The Wash Cycle I Get A F- Blinking Light.
(Posted by Anonymous-131833 10 years ago)
Kenmore He2t 3.7-cubic-foot Front-loading Washer Wont Start
(Posted by flFe 10 years ago)
My Washer Agitates On Startup And Fills During Rinse Cycle
(Posted by shawnrandle 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)