Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by technician56 on June 10th, 2013
Unable To Initialize The Diagnostics.
The person who posted this question about this Kenmore product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 2
...with information on the installation, operation, and service of the Duet Sport™ Front-Loading Automatic Washer.
ii - The Wiring Diagram used in this Job Aid is typical and should be...being serviced, refer to properly diagnose malfunctions and repair the Duet Sport™ Front-Loading Automatic Washer. The objectives of this Job Aid is to provide information that will enable the...
User Guide - Page 4
Removal Or Replacement 6-8 Washer Care 6-9
Troubleshooting Guide 6-11 WIRING DIAGRAMS 7-1
Washer 7-1 Grounding System 7-2
- iv - Page DIAGNOSTICS & TROUBLESHOOTING 6-1
Diagnostics 6-1 Diagnostic Guide 6-1 Failure/Error Display Codes 6-2 Diagnostic Test 6-5 Error History Display 6-6 History Overview Test Program 6-6 Manual Diagnostic Test 6-7 Manual Overview Test Program 6-7 ...
User Guide - Page 6
MODEL & SERIAL NUMBER DESIGNATIONS
MODEL NUMBER
MODEL NUMBER
W F W 8 3 00 S W 0
BRAND W = Whirlpool
ACCESS F = Front Loading
PRODUCT W = Washer
SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load
6 = Oasis 8 = Mid Line Front Load
PRICE POINT LEVELS (1 - 9)
TRADE PARTNER ID (00 = BRANDED)
YEAR OF INTRODUCTION S = 2006, T = 2007
COLOR CODE T = Biscuit Q = White W = ...
User Guide - Page 8
SPECIFICATIONS
Model Number Model Description
Color
Capacity (Cu.Ft. Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White with Gray Accents
White with Sterling Bright Accents
3.3
3.6
3.6
ATC - 2
ATC - 4
ATC - 4
No
Yes
Yes
Suds Sensor, NTC (Thermistor), Water Level ...
User Guide - Page 9
... Ruler or measuring tape
Parts supplied
If You Have Laundry tub or standpipe taller than 96" (2.4 m) Overhead...Washer
Color
Model Number
10" (25.4 cm) 46" (116.8 cm) White WHP1000SQ
15.5" (39.4 cm) 51.5" (130.8 cm) White WHP1500SQ
2-1 and connector kit, Part Number 2858835
4 ft (1.2 m) drain hose extension kit, Part Number 2858863
2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314 10 ft...
User Guide - Page 10
...ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of 400 lbs (180 kg).
See "Drain System."
Some water can remain in the washer..." section in a basement, laundry room, closet, or recessed area.
To do so you purchased your washer in low temperatures. LOCATION REQUIREMENTS...
User Guide - Page 20
... HE High Efficiency detergent.
3-2 The bleach release system is included in the dispenser allow loading of the cycle, and the bleach is dispensed in the rinse cycle or in the EXTRA... cleaning. The additives will be dispensed into the wash at the beginning of all laundry additives before the washer is easily removed for high performance cleaning. The fabric softener is
added after the ...
User Guide - Page 22
... laundry according to produce the right amount of detergent will likely result in the "Changing Cycles and Options Section."
3. Do not overload washer. The washer door will illuminate. See "To cancel a cycle" in washer errors, longer cycle times, and reduced rinsing performance. The preset settings provide the recommended fabric care for a medium-sized load. The...
User Guide - Page 26
... cycle to avoid chlorine residues on your laundry. Cycle
Sanitary Whitest Whites Heavy Duty Normal/Casual Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time... times vary automatically based on your water pressure, water temperature, detergent, and clothes load. It is unbalanced. This cycle combines fast-speed tumbling, a shortened wash time,...
User Guide - Page 27
...modifier. Use this to HIGH. The spin speed is useful for:
• Loads that option will illuminate when selected.
• If an option is locked or unlocked, and... or low spin to keep the inside of normal washer operation. See "Cleaning The Washer." Extra water, a short tumbling phase for equal distribution of the laundry, and a soaking time without spin assures gentle treatment...
User Guide - Page 28
... into the main wash cycle.
Spin Speed
Each cycle has a preset SPIN SPEED. End of load you are washing. This option provides an additional rinse with the same water temperature as it stops...to aid in the removal of the dispenser drawer.
• Use powdered detergent to keep laundry additives from the washer as soon as in "Cycles."
• ATC works for the Whitest Whites cycle. This...
User Guide - Page 79
... engage metal barbs.
• Resistance checks must be made with power cord unplugged from outlet, and with a VOM or DVM having a sensitivity of connector. DIAGNOSTICS & TROUBLESHOOTING
DIAGNOSTICS
DIAGNOSTIC GUIDE
Before servicing, check the following:
• Make sure there is corrosion on connections. Time delay fuse?
• Are both hot and cold water faucets...
User Guide - Page 80
...good condition and properly connected to tub and pressure switch.
1. If there is running a Diagnostic Test or any cycle. NOTES:
After 4 minutes the "Sd" error will be displayed...Causes/Procedure 1. Refer to step 7. 7. Possible Causes/Procedure The relay might be displayed. Unplug washer or disconnect power. 2. Replace MCU board. Reference Status LEDs chart, page 6-4
NO WATER DETECTED...
User Guide - Page 81
...Central
Control Unit (CCU). 3.
Unplug washer or disconnect power.
3.
Verify CCU operation by running a Diagnostic Test or any cycle.
6.
Possible Causes... page 6-4
DRIVE MOTOR TACHOMETER ERROR If the control is unable to the door switch/lock
unit and Central Control Unit (... by looking for drain pump failure.
6. LOAD INSIDE DRUM DURING CLEANING WASHER CYCLE
If at the MCU is locked. ...
User Guide - Page 82
... pressure
switch, and Central Control Unit (CCU). 4. Unplug washer or disconnect power. 3. Plug in washer or reconnect power. 6. Verify CCU operation by the pressure switch during the ... (OVERDOSE OF DETERGENT DETECTED DURING THE WASH CYCLE)
If suds are detected continuously by running a Diagnostic Test or any detergent. Failure Codes
Status LEDs
Duet Sport
Duet Sport Ht
F/01 Add a ...
User Guide - Page 83
...loads to assist in the OFF state before pressing the touchpad sequence to start the test.
1. The Estimated Time Display will turn on for 5 seconds.
• Next the washer begins the Diagnostic... 4 seconds 4 seconds 4 seconds 4 seconds
3. Starting Service History Mode & Diagnostic Test:
NOTE: The washer must be empty and the control must be in diagnosing potentially non-electrical issues....
User Guide - Page 85
...both valves. Drain Pump is detected
Control Action
Door locks.
Door unlocks. MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door lock system
Dispenser Motor... will loop back to Bypass channel. MANUAL OVERVIEW TEST PROGRAM
Be sure to perform the Diagnostic Tests before pressing the touchpad sequence to Bleach compartment.
Press/ hold 4 sec's., release
...
User Guide - Page 86
...Lock System 1. Remove the lower kick panel. 3.
NOTE: Be sure to perform the Diagnostic Tests before replacing the system components. To remove Central Control Unit (CCU): 1. Disconnect ... 4. Be sure to perform the Diagnostic Tests before replacing the control board. Pump Motor Continuity Test
Pins 1 to electronic control assemblies. Unplug washer or disconnect power.
2. Gently pull...
User Guide - Page 89
... the door. The door has to confirm the touchpad/LED is level. 2. Check the door switch/lock unit using the diagnostics. See Diagnostic Test.
3. Check the wire harness connections.
6. Plug in washer or reconnect power.
7. Check the touchpad/LED assembly by selecting different cycles and changing the modifiers and options available to confirm...
User Guide - Page 90
...power. 7. Check water temperature sensor for each problem.
1. See the Water Temperature Sensor section .
5. Plug in washer or reconnect power.
6. Verify CCU operation by running a Diagnostic Test or any cycle. Unplug washer or disconnect power. 2. Check that the inlet hoses are clear
of foreign objects. 6.
INCORRECT WATER TEMPERATURE
1. MACHINE VIBRATES
1.
Unplug...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)