Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by debmomofmamy on April 12th, 2013
My He2t Shows Me A F28 Error. How Do I Get The Door Unlocked To Get My Clothes.
It has shown me this error before and I unlugged it and it worked again This time it is not working ad I cannot even get the door to unlock to get my clothes out. Can you tell me how to remedy this please
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 22
... High Efficiency detergent. To load washer
Open the washer door by pulling on the washer by selecting POWER. Washer door should be filled with equal amounts of material.
• When unloading garments, occasionally check under the rubber rim at the front of sorted clothes in washer errors, longer cycle times, and reduced rinsing performance. The washer door will illuminate. Open...
User Guide - Page 23
...door unlocks, and the wash load can be marked "HE" or "High Efficiency." Select START. USING THE DISPENSER
The washer...of detergent to use the proper dispensers when adding laundry additives. Use only HE High Efficiency detergent....washer errors, longer cycle times, and reduced rinsing
performance.
The washer powers down the washer manually after the cycle is for your laundry...
User Guide - Page 24
...load.
• Always measure liquid chlorine bleach. To stop a cycle and select a new cycle
1. Select the desired OPTIONS. STATUS LIGHTS
These lights show which comes with all Options are locked.
3-6
The washer powers down, the door unlocks, and clothes can be changed anytime before the door unlocks... RESTARTING
1. To pause the washer at the best time during the first rinse...
User Guide - Page 25
...shown in the Preset Cycle Settings table. To unlock the door after the cycle is illuminated. You can also use of your water pressure, water temperature, detergent, and clothes load.
The CONTROL LOCKED status light illuminates. The door is locked and unlocked automatically, depending on your garments.
Adding items
You can add items to the washer... Time Remaining
The cycle times ...
User Guide - Page 26
...Whites Heavy Duty Normal/Casual Quick Wash (2-3 items) Delicate/ Hand Wash Clean Washer Rinse/Spin Drain/Spin Soak
Estimated
Time* (hr:min)
Wash Temp
3:00
Super Hot
153°F (67°C)...The cycle times vary automatically based on your water pressure, water temperature, detergent, and clothes load. This cycle combines a super hot water temperature and fast speed tumbling to wash loads of ...
User Guide - Page 27
... phase for equal distribution of the laundry, and a soaking time without spin assures gentle treatment, even for each Wash Cycle selection.
• If an option is unavailable with all options are part of normal washer operation. You will hear sounds that need rinsing only.
• Adding fabric softener to a load using the fabric softener dispenser...
User Guide - Page 30
...the door will unlock, lock again, and then the cycle will continue.
• The machine will not fill, but the basket will stop the cycle. Washer Maintenance Procedure
This washer has...3.
This will cause damage to the unit and clothing added to Step 8.
Open the washer door and remove any clothing or items from the washer.
2. The door will proceed to the next cycle.
d) Wipe...
User Guide - Page 31
...drawer is complete, leave the door open door to maintain washer freshness
• Use only HE High Efficiency detergent.
• Leave the door slightly open after five...cloth or sponge to the drawer.
Wash the parts under running water. To winterize washer:
1. Disconnect water inlet hoses from the softener and bleach compartments).
3. Do not use washer again:
1. Unlock...
User Guide - Page 33
...washer or reconnect power. An error code may hear various sounds when the door is on a pedestal, the washer must be tightened against the washer cabinet.
Are screens at equal heights.
• Is the washer gurgling or humming? Select DRAIN/SPIN if there is drained from the washer, you are part of the washer must be shown... washer drum. You may be in the Estimated Time ...
User Guide - Page 34
...) for details.
• Are the laundry additives in the fabric softener dispenser.
• Did you run the Clean Washer Cycle lately? Do not use ? This is normal. WASHER ODOR
• Have you put powdered or liquid color-safe bleach into the dispensers. Use of each hose. The door will unlock at the end of the...
User Guide - Page 36
....
• Did the load cause imbalance? The washer will add time to redistribute the load with additional tumbling.
• Did you washing a single item or bulky load? Sort dark clothes from lint takers (corduroy, synthetics). As your frequency of your water pressure, water temperature, detergent, and clothes load. RESIDUE, LINT, STAINS ON LOAD; The cycle times vary automatically based on...
User Guide - Page 43
...MI3 Serial Com 3 BU Wires Red Stripe
Not Used
UI8 - Drive Motor WH Stripe
IF2 - Door Lock 3 BK Wires GN Stripe
Board Edge Connectors
HE2 -
DS2 - Heater
MS2 - Line Filter ... BU Wires BU Stripe
VCH7 - Door Lock Switch BK Stripe
CENTRAL CONTROL UNIT
Connector Locking Tabs
4-5 User Interface 1 BK, 7 WH Wires
DI6 - REASSEMBLY NOTE: The photo shows the connector callouts for the central ...
User Guide - Page 53
... it over so that you can access the connectors. d) Remove the bellows retaining clamp from the door switch assembly (see the photo in step 7b).
To remove the bellows:
a) Remove the two ... and 16 on the next page.
4-15
d) Unlock the tabs and disconnect the three wire connectors from the washer (see the top right photo). c) Pull the door switch assembly out and turn it from one end ...
User Guide - Page 75
... Sol. Replace all parts and panels before accessing. Unplug washer or disconnect power. 2. Pins 1 & 3 = 60 Ω
5. Disconnect the door lock/unlock sole- The meter should indicate as follows:
Door Unlock Solenoid - Pins 2 & 3 = 60 Ω Door Lock Solenoid - Disconnect the door switch connector DS2 (see page 4-5) from the CCU.
6. Failure to page 4-14 for the procedure for accessing...
User Guide - Page 80
... harness connections to step 7. 7. Unplug washer or disconnect power. 2. Verify inlet valve operation. WATER TEMPERATURE SENSOR ERROR If the water temperature sensor (NTC) value is no water in good condition and properly connected to lock the door. HEATER FAILURE If the temperature increase during high-speed spin the door unlocks after 6 minutes. Possible Causes/Procedure...
User Guide - Page 81
...Status LEDs chart, page 6-4
Reference Status LEDs chart, page 6-4
DOOR UNLOCK ERROR
If the door unlock has failed 6 times. Door switch/lock unit failure.
1. Check wire harness connections to the dispenser ...Procedure Remove clothes from dispenser motor to the left when facing the MCU connectors.
Unplug washer or disconnect power. 3.
Check the MCU by weight. Unplug washer or ...
User Guide - Page 83
...of error codes. This executes the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press EXTRA RINSE four times within...Operation modes:
• Display the error states that have been recorded by the appliance.
• Run through an automated test.
• Run loads to assist in the OFF state before...
User Guide - Page 84
... 5 seconds.
At the end of the cycle lights will flash and the error code will be displayed on the status lights.
• The next most recent error code is to be Checked
Door lock system
Clean Washer Delicate
Clean Washer
Distribution system is set to the maximum speed.
Delicate/Hand Wash
Distribution system is...
User Guide - Page 85
...Door locks. Door unlocks.
Release for 4 sec's.
Filling only by the Hot valve.
To be in the OFF state before replacing the system components. MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door...key press or completion
On key press only after rpm = 0 and door is unlocked
Distribution system is set to Main Wash compartment. For model Duet Sport HT...
User Guide - Page 88
... after each cycle to be completed.
9.
This will unlock. b) If any items are detected in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will determine if clothing or other causes.
6-10 Be sure the door is closed .
3. The cycle will remain lit. Press PAUSE/CANCEL to start...
Similar Questions
Follow Up To The Kenmore He2t Washer F20 Error Code.
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
I replaced the pressure switch and the water inlet valve with a new, hem parts. After restarting the...
(Posted by riskoj 7 years ago)
Where Is The Mcu Located On A Kenmore He2t Front Loading Washer
(Posted by DRobRoha 10 years ago)
Kenmore He2t 3.7-cubic-foot Front-loading Washer Wont Start
(Posted by flFe 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
I Replaced The Door Latch Lock On My Front Load Washer The Washer Won't Come On
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
I was told the door lock latch needed to be replaced. When the door latch lock was replaced the wash...
(Posted by reginaharvey 11 years ago)