Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Question posted by landbbarber on September 13th, 2013
Flashing Spin Light
The machines spin light is flashing with 9 minutes left on cycle and the door is locked. I push the stop button to try to stop and nothing happens and I push the power button and nothing happens . I cannot get it to do anything. What can I do?i cannot get it to unlock or turn off.
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 8
... Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White...
User Guide - Page 19
...adapts to the load size and to the cycle selected to a load. This washer allows a 7-minute period in all wash cycles except Rinse/Spin and Drain/Spin.
ELECTRONIC CONTROLS
Flexible electronic controls are a beginner or an expert.
The motor can obtain the same results with traditional top load machines. You are evenly balanced.
3-1 For some cycles, the default spin speed can wash...
User Guide - Page 22
... the desired OPTIONS. Using regular detergent will illuminate. See "Options."
6. To load washer
Open the washer door by pulling on the washer by pushing it stops. The door can begin the wash cycle immediately
Select and hold START (for this type of choosing a cycle, the washer automatically shuts off.
3-4 Washer door should be marked "HE" or "High Efficiency." Press END OF...
User Guide - Page 23
.... 2.
Dispenser release lever B. Laundry additives are made to produce the right amount of suds for you to return to this type of water to remain in washer errors, longer cycle times, and reduced rinsing
performance.
• When the wash cycle is complete, the CYCLE COMPLETE status light illuminates, the door unlocks, and the wash load can be marked...
User Guide - Page 24
... use .
• Do not fill beyond the "MAX" level. To change Options after the wash cycle. To continue the cycle, select and hold START (for approximately 1 second). Select PAUSE/CANCEL once.
2. The washer powers down, the door unlocks, and clothes can add an additional item to begin the drain.
4.
Select PAUSE/CANCEL once.
2.
To...
User Guide - Page 25
.... The door is operating. Each cycle is designed for the cycle selected will be added.
2. Select and hold START (for approximately 1 second) to 30 minutes under extreme conditions. The washer will then power down. To continue the cycle, close the door and select and hold START (for approximately 1 second).
3. Door Locked
When the status light illuminates, the door is unbalanced...
User Guide - Page 26
...-speed spin, and a load cooling process to shorten drying times.
Delicate/Hand Wash
Use this cycle to ensure proper performance during this cycle to wash loads of heavy soils and stains.
This cycle combines a super hot water temperature and fast speed tumbling to wash loads of bleach. Whitest Whites
This cycle is recommended that are needed in the machine...
User Guide - Page 27
... all cycles.
• See the "Laundry Guide" section for an overview of set -in stains. You may hear various sounds when the door is useful for:
• Loads that option will be a short tone and the light for that need rinsing only.
• Adding fabric softener to a load using the fabric softener dispenser. Rinse & Spin is locked or...
User Guide - Page 28
... loads of heavily soiled garments that bleed or fade Light soils
In wash water temperatures colder than 60°F (15.6°C), detergents do not dissolve well. Wash Temp
Each cycle...garments. The washer continues automatically from the washer as soon as in "Cycles."
• ATC works for all rinse cycles is illuminated. To change the spin speed, select the SPIN SPEED button until the ...
User Guide - Page 29
... Washer No clothes
Rinse & Spin
All loads
Drain & Spin
All loads
Soak
All loads
Delay Wash
AVAILABLE OPTIONS
Extra Rinse
Pre
End of these washer cycles. Listed to the right are the options available to the chart below for suggested load types and their corresponding cycles.
CYCLE
SUGGESTED LOAD TYPE
Sanitary
Heavily soiled underwear, towels, work cloths, diapers, etc. LAUNDRY...
User Guide - Page 30
... the door will unlock, lock again, and then the cycle will continue.
• The machine will not fill, but the basket will remain lit. Washer Maintenance Procedure
This washer has a special cycle that follows. Then repeat steps 1, 2 and 6 to thoroughly clean the inside of warm tap water.
b) Wipe the seal/bellow area with door open.
c) Let stand 5 minutes...
User Guide - Page 33
... the cycle Unplug washer or disconnect power. If the washer is normal.
• Were the 4 shipping bolts in death, fire, or electrical shock. These new sounds and pauses are part of the machine removed? Do not use an extension cord. The washer must be tightened against the washer cabinet.
This happens during the washing, rinsing, or spinning process...
User Guide - Page 34
... the laundry additives in the dispenser compartment. Measure detergent and fabric softener. This is opened during the spin?
Press PAUSE/CANCEL once.
To avoid odors leave the door open after the start of the washer during "Add a garment"? Wipe up out of the drain.
• Is the door locked and is the "Add a garment" light on some...
User Guide - Page 36
....
Add items or try again.
• Did you wash a large load on your garments without increasing cycle times. Dye transfer can be balanced. The wash load must be fully loaded, but not tightly packed. The washer will start a Drain/Spin cycle. CLOTHES CARE
LOAD TOO WET
• Did you add detergent to redistribute the load. If the laundry is complete, then...
User Guide - Page 37
Unload the washer as soon as it stops.
• Did you use liquid detergent for small, lightly soiled loads. Add liquid fabric softener to reduce wrinkling.
• Did you using liquid detergent.
• Did you use the right cycle for the load being washed? Use the Delicate cycle or another cycle with this washer. The wash load must be balanced and...
User Guide - Page 80
...NO WATER DETECTED ENTERING MACHINE OR PRESSURE SWITCH ...minutes the water valves turn off. Possible Causes/Procedure Door lock mechanism is not a siphon problem.
2.
Refer to the Water Temperature Sensor section. FAILURE/ERROR DISPLAY CODES
Communication of failure codes will be displayed. Verify CCU operation by running a Diagnostic Test or any cycle. Unplug washer or disconnect power...
User Guide - Page 81
... cycle again.
6-3 Possible Causes/Procedure Door lock mechanism is cleared. Unplug washer or disconnect power. 3.
MCU FAILURE
If the heat sink gets too hot, the Motor Control Unit (MCU) will stop the motor, the MCU will communicate this failure to the Central Control Unit (CCU), then the CCU will show. Check wire harness connections to the left...
User Guide - Page 82
.... 8. Run the unit through a RINSE/SPIN cycle. - Check/clean drain pump filter of the excess detergent.
1. Verify CCU operation by the pressure switch during the drain or spin phases, the washer will fill 4 liters of water and during 5 minutes the unit will rest without adding any
cycle. Unplug washer or disconnect power. 3. Check wire harness connections to show...
User Guide - Page 83
....
• Run loads to start the test.
1. If there are any failure codes, all the lights on the console will turn on for Press/hold 4 seconds 4 seconds 4 seconds 4 seconds 4 seconds
3. This executes the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press...
User Guide - Page 84
... Duet Sport Ht
Rinse/Spin
Rinse/Spin
Control Action Door locks.
At the end of the cycle lights will flash and the error code will be displayed on the status lights.
• The next... seconds the lights will turn off for 0.5 seconds and then all turn off and the most recent error code is to be Checked
Door lock system
Clean Washer Delicate
Clean Washer
Distribution system ...
Similar Questions
Door Lock Light Does Not Come On
When starting a load of clothes to wash, it clicks several times and door lock light does not come o...
When starting a load of clothes to wash, it clicks several times and door lock light does not come o...
(Posted by mikeballard56 2 years ago)
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)