Kenmore HE2t Support Question
Kenmore HE2t Support Question
Find answers below for this question about Kenmore HE2t - 3.7 cu. Ft. Front Load Washer.Need a Kenmore HE2t manual? We have 1 online manual for this item!
Current Answers
Related Kenmore HE2t Manual Pages
User Guide - Page 4
Removal Or Replacement 6-8 Washer Care 6-9
Troubleshooting Guide 6-11 WIRING DIAGRAMS 7-1
Washer 7-1 Grounding System 7-2
- Page DIAGNOSTICS & TROUBLESHOOTING 6-1
Diagnostics 6-1 Diagnostic Guide 6-1 Failure/Error Display Codes 6-2 Diagnostic Test 6-5 Error History Display 6-6 History Overview Test Program 6-6 Manual Diagnostic Test 6-7 Manual Overview Test Program 6-7 Electronic ...
User Guide - Page 6
... NUMBER
MODEL NUMBER
W F W 8 3 00 S W 0
BRAND W = Whirlpool
ACCESS F = Front Loading
PRODUCT W = Washer
SERIES 5 = Whirlpool Leap 7 = 24˝ Front Load 9 = Duet Front Load
6 = Oasis 8 = Mid Line Front Load
PRICE POINT LEVELS (1 - 9)
TRADE PARTNER ID (00 = BRANDED)
YEAR OF INTRODUCTION S = 2006, T = 2007
COLOR CODE T = Biscuit Q = White W = White With Metallic Accent R = White With...
User Guide - Page 8
... Model Description
Color
Capacity (Cu.Ft. IEC) Temperature Control
Heater Sensors
Tumble Speed
Spin Speed
Motor Voltage Frequency Amps Water Consumption Average DOE (Gallons-Per-Cycle) Rated Load Load Pounds
Height Install Depth: Min - Max
Width Product Weight (approx)
WFW8300SW
WFW8500SW
WFW8500SR
Front Load Washer
Front Load Washer
Front Load Washer
White with Gray Accents
White...
User Guide - Page 10
... temperatures. You will need
• A water heater set to deliver 120°F (49°C) water to the washer.
• A grounded electrical outlet located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).
• A level floor with a total weight (water and load) of where...
User Guide - Page 13
Failure to follow these instructions can result in death, fire, or electrical shock.
• A 120 volt, 60 Hz., AC only, 15- WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer... codes and ordinances. For a permanently connected washer:
This washer ...
User Guide - Page 14
... valve. Once all 4 bolts are removed. Failure to the valves can result in back or other injury. Damage to do so can result. Excessive Weight Hazard Use two or more people to move it to the water faucets
Make sure the washer drum is within approximately 3 ft (90 cm) of the rear panel...
User Guide - Page 17
... Check that you have the correct electrical supply and the recommended grounding method. Failure to clean your tools.
4. To test and to follow these instructions can ...detergent into the detergent dispenser.
Check for a medium sized load. Select NORMAL/CASUAL, and then select START. Dispose of your washer, use
1/2 the manufacturer's recommended amount for leaks around ...
User Guide - Page 22
... laundry additives to use. See "Wash Cycles."
5. USING THE PROPER DETERGENT
Use only High Efficiency detergents. Close the washer door by pulling on the washer by turning the cycle selector. If desired, select the END OF CYCLE SIGNAL. Follow the manufacturer's instructions to determine the amount of detergent will illuminate. To load washer...
User Guide - Page 23
... slowly and
completely (to the wash cycle will likely result in component failures and noticeable mold or mildew. A C
MAX
DETERGENT
LIQUID BLEACH SOFTENER
... your laundry additives-one is for detergent, one is for liquid fabric softener. The washer powers down the washer manually ... and the wash load can be added to produce the right amount of water to the washer during Delay, before...
User Guide - Page 30
... unlock. The door will determine if clothing or other items are detected in the washer.
• Wear rubber gloves when cleaning for prolonged periods.
• Refer to check for stained areas.
Then repeat steps 1, 2 and 6 to cancel the failure code. b) Wipe the seal/bellow area with door open.
Press PAUSE/CANCEL to start...
User Guide - Page 32
... drain system and attach to rear panel clips.
4. Unit must be properly set up for a medium sized load. Run the washer through the Normal/Ca- Electrical Shock Hazard Plug into a grounded 3 prong outlet. Failure to clean the washer and remove the antifreeze, if used. Unplug the power cord.
3. IMPORTANT: Call service.
Use only HE...
User Guide - Page 33
...These new sounds and pauses are part of draining. Do not remove ground prong. Failure to follow these instructions can result in firm contact with any new product, ...? TROUBLESHOOTING
WASHER & COMPONENTS
ERROR CODES
When all four pedestal feet must be level. An error code may hear air being pulled through the pump. The washer must be tightened against the washer cabinet.
See...
User Guide - Page 80
.../Procedure 1. Check connection to step 7. 7. Check resistance of heating element, if present on the washer console by looking for possible leaks.
6. Check the water temperature sensor and connection to it is ...ashing and standing status lights. FAILURE/ERROR DISPLAY CODES
Communication of failure codes will be soldered or always open. - played on this
model. (abnormal = infinity...
User Guide - Page 81
... disconnect power.
2. Make sure all grounding switches are removed.
2. Plug in washer or reconnect power. 6. Check door switch/lock unit for drain pump failure.
6. NOTE: The door switch/lock unit can be driven to the top
of the CLEANING WASHER cycle a load is completely closed for proper shut off hot and cold water faucets...
User Guide - Page 82
... tumbling, the water will be drained and it is not plugged or kinked.
2. Check drain pump. 7.
Failure Codes
Status LEDs
Duet Sport
Duet Sport Ht
F/01 Add a Garment
Add a Garment
F/11 Add a Garment, ...or drain again. Plug in washer or reconnect power. 6. This should clear the unit of foreign objects. 5. Check wire harness connections to show the failure codes. Run the unit through ...
User Guide - Page 83
...; Run loads to reach the Diagnostic Test. This executes the automatic test but does not show the error history.
• Close the door.
• Push POWER.
• Select the CLEAN WASHER cycle.
• Press EXTRA RINSE four times within 5 seconds.
• Press EXTRA RINSE to advance to performing any more failure codes all console...
User Guide - Page 85
...the key):
Press/ hold 4 sec's.
Stop motor to Main Wash compartment. MANUAL DIAGNOSTIC TEST
The washer must be empty and the control must be Checked
Door lock system
Dispenser Motor Dispenser contact Cold and...
• To cancel out of the procedure the program will loop back to the next failure code.
• At the end of the Manual Test Mode press PAUSE/CANCEL.
To be in the ...
User Guide - Page 88
..., leave the door open after each cycle to allow for other items are in the washer, all cycle lights will flash and the WASH and CONTROLS LOCKED lights will determine... cycle to cancel the failure code.
b) If any clothing or items from the washer.
2. Open the washer door and remove any items are detected in the washer, it will rotate while the washer runs a short sensing ...
User Guide - Page 89
...Verify CCU operation by running a Diagnostic Test or
any cycle. Plug in washer or reconnect power. 6. this could indicate a failure
to confirm the touchpad/LED is level. 2. Check operating pressure switch....be performed in the sequence shown for a Fault/Error Code on the display. 2. See Diagnostic Test.
3. WON'T SHUT OFF 1. Plug in washer or reconnect power.
7. Check under Won't Dispense ...
User Guide - Page 90
... connections. 3. Check drain pump. 4.
INCORRECT WATER TEMPERATURE
1. Check water temperature sensor for each problem.
1. DISPLAY FLASHING
See Failure/Error Display Codes.
6-12 Plug in washer or reconnect power.
6. Remove shipping system. 2. Check leveling feet. Plug in washer or reconnect power. 7. Verify CCU operation by running a Diagnostic Test or any cycle. Unplug...
Similar Questions
What Is The Purpose Of Running A Diagnostic Test On Kenmore Front Load Washer
(Posted by dabawa 10 years ago)
Kenmore He2t Front Loading Washer Model# 110.4756
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
When I turn power on the front panel lights up, but when I push start it all shuts down. Tried unplu...
(Posted by cpcalder 11 years ago)
What Does It Mean When A Kenmore Front Load Washer Model # 48102 Turns Off And O
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
what does it mean when a kenmore front load washer model # 48102 turns off and on during the washing...
(Posted by kemackey86 11 years ago)
Why Front Load Washer 4044 Won't Start The Cycle?
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
Yesterday while my front load washer 4044 was starting to do its first normal cycle , which usually ...
(Posted by martinezmarly 12 years ago)
Does This Front Load Washer Need To Have Bolts Installed To Move From Another St
model#110.47571602 HE2t frontload washer locking bolts for moving?
model#110.47571602 HE2t frontload washer locking bolts for moving?
(Posted by donnasilver 12 years ago)